Preparation of lithium-ion polymer battery using LiNi1/3Co1/3Mn1/3O2 as a cathode material and its electrochemical properties

In this work, LiNi_1/3Mn_1/3Co_1/3O₂ powders were synthesized from co-precipitated spherical metal hydroxide. In the voltage range of 2.8–4.2, 2.8–4.4, and 2.8–4.6 V, the discharge capacities of LiNi_1/3Mn_1/3Co_1/3O₂ electrode were 163, 177, and 193 mAh⋅g⁻¹, respectively. A gel polymer electrolyte (GPE) was also prepared using polyoxyalkylene glycol acrylate (POAGA) as a macromonomer. LiNi_1/3Mn_1/3Co_1/3O₂/GPE/graphite cells were prepared and their electrochemical properties were evaluated at various current densities and temperatures. The ionic conductivity of the GPE was more than 6.2 × 10⁻³ S⋅cm⁻¹ at room temperature. POAGA-based cells were showed good electrochemical performances such as rate capability, low-temperature performance, and cycleability.     

Preparation of a sensor substrate using functionalized mesoporous silica on a gold film for surface plasmon resonance (SPR) spectroscopy

The use of surface plasmon resonance (SPR) spectroscopy has been applied to a wide variety of fields such as biosensors and surface analysis instruments. In general, a SPR substrate is prepared using self-assembled monolayer (SAM) method of organic molecules as receptor for the target on a layer of gold or silver. However, mesoporous inorganic materials such as SBA-15 have benefits as sensor substrate for SPR. Mesoporous silica has a large surface area which receptor molecule can be attached and has a rigid body which has an excellent stability in the extreme condition compared to organic sensing layer. We prepared an organic modified mesoporous silica and successfully immobilized it on a gold surface, in an attempt to use as a substrate for SPR spectroscopy. For the comparison of sensitivity of prepared substrate, Pt²⁺ detection was selected as a model system. Substrate prepared in this study exhibited the capability of selective sensing for Pt²⁺ ions.     

High performance series-resonance energy-recovery circuit for plasma display panel

A new high performance series-resonance energy-recovery circuit (ERC) for a plasma display panel (PDP) is proposed. Two different ERCs are used for both sides of the PDP, and the slow falling and fast rising times are employed. Therefore, it features the zero voltage switching, low electromagnetic interference, low current stress, no severe voltage notch, and high energy-recovery capability.     

A simple receding horizon control for state delayed systems and its stability criterion

In this paper, a simple receding horizon (or model predictive) control for state delayed systems is presented and its solution is given in a closed form by a reduction method. While the control for a time-delay system is usually complex, the proposed controller is simple to construct and therefore can be simply implemented in real applications. To check the closed-loop stability of the proposed controller, a sufficient condition is provided by linear matrix inequalities. In addition, a numerical algorithm is presented for computing the eigenvalues of systems with distributed time delays, which can be used as a necessary and sufficient condition to check closed-loop stability. It is shown by simulation that this simple control can be a stabilizing control for time-delay systems.     

Scalability analysis of declustering methods for multidimensionalrange queries

Efficient storage and retrieval of multi-attribute data sets has become one of the essential requirements for many data-intensive applications. The Cartesian product file has been known as an effective multi-attribute file structure for partial-match and best-match queries. Several heuristic methods have been developed to decluster Cartesian product files across multiple disks to obtain high performance for disk accesses. Although the scalability of the declustering methods becomes increasingly important for systems equipped with a large number of disks, no analytic studies have been done so far. The authors derive formulas describing the scalability of two popular declustering methods-Disk Module and Fieldwise Xor-for range queries, which are the most common type of queries. These formulas disclose the limited scalability of the declustering methods, and this is corroborated by extensive simulation experiments. From the practical point of view, the formulas given in the paper provide a simple measure that can be used to predict the response time of a given range query and to guide the selection of a declustering method under various conditions     

Exact static element stiffness matrices of non‐symmetric thin‐walled curved beams

An evaluation procedure of exact static stiffness matrices for curved beams with non‐symmetric thin‐walled cross section are rigorously presented for the static analysis. Higher‐order differential equations for a uniform curved beam element are first transformed into a set of the first‐order simultaneous ordinary differential equations by introducing 14 displacement parameters where displacement modes corresponding to zero eigenvalues are suitably taken into account. This numerical technique is then accomplished via a generalized linear eigenvalue problem with non‐symmetric matrices. Next, the displacement functions of displacement parameters are exactly calculated by determining general solutions of simultaneous non‐homogeneous differential equations. Finally an exact stiffness matrix is evaluated using force–deformation relationships. In order to demonstrate the validity and effectiveness of this method, displacements and normal stresses of cantilever thin‐walled curved beams subjected to tip loads are evaluated and compared with those by thin‐walled curved beam elements as well as shell elements. Copyright © 2004 John Wiley & Sons, Ltd.     

Microstructural Factors Controlling Blunt- and Sharp-Notch Toughness in La-Added 8Ni-13Co Secondary Hardening Steel

Toughness variations of sharp and blunt notches were studied. For the quantitative analysis of various particles, small-angle neutron scattering was conducted. Under the 1323 K (1050 °C), and the 1473 K/1323 K and 1473 K/1173 K (1200 °C/1050 °C and 1200 °C/900 °C) (high-temperature initial step and low-temperature final step) austenitizing conditions, the impact toughness underwent changes as follows: 30→30→43 J. In contrast, the fracture toughness underwent variations as follows: 90.5→120→114 MPa $ \sqrt {\text{m}} $ m . Blunt- and sharp-notch toughness parameters were found to be mainly dependent on grain size and primary particles, respectively. The microstructural dependence of toughness with notch acuity is discussed in detail.     

Advances in Soft Materials for Sustainable Electronics

In the current shift from conventional fossil-fuel-based materials to renewable energy,ecofriendly mate-rials have attracted extensive research interest due to ...     

The effect of substrate temperature on Al-doped ZnO characteristics for organic thin film transistor applications

The influence of substrate temperature on the structural, electrical, and optical properties of aluminum-doped zinc oxide (AZO) films fabricated by radio frequency (RF) magnetron sputtering was investigated. The AZO films were deposited at various substrate temperatures, and the effect of AZO gate electrode conductivity on organic thin film transistor (OTFT) performance was examined. While an increase in the substrate temperature from 100 °C to 300 °C led to an improvement in crystallinity, substrate temperatures over 300 °C caused degradation of the electrical and surface properties. We fabricated OTFTs using AZO films prepared at various substrate temperatures and obtained good device performance. Thus, the performance of an OTFT can be determined by the conductivity of the AZO gate electrode.     

Polymeric (SU-8) optical microscanner driven by electrostatic actuation

A torsional micromechanical scanner was fabricated using photosensitive polymer (SU-8). The proposed polymer-based optical microscanner with reduced torsional stiffness offers a new approach to increase scanning angles. The scanner consists of two parts; the top layer (micro mirror and electrodes) and the bottom layer (anchors and electrodes). The SU-8 scanner is actuated by electrostatic force generated by gap-closing electrodes. For the fabricated optical scanner with the mirror size of 3 × 3 mm², the experimentally obtained scanning angles were 0.43° for 60 Hz (non-resonant) and 1.54° for 1.13 kHz (resonant) at the input voltage of 160 V. This paper also proposes a simple and new fabrication method, which can effectively control the stiffness of the torsional springs by molding SU-8 photoresist through V-groove on the silicon substrate, thereby increasing the scanning angles.