Optimal solutions for a dynamic bandwidth allocation scheme in high-speed networks

In this paper, we investigate the problem of determining the optimal bandwidth allocation for a Dynamic Bandwidth Allocation Scheme (DBAS). The objective is to minimize the total amount of bandwidth required to satisfy the Quality of Service (QoS) requirements of all traffic streams. It is shown that when the performance functions satisfy a certain number of conditions, there exists a unique optimal bandwidth allocation such that, for each traffic stream, either its QoS is just satisfied or its QoS is over-satisfied and it is allocated zero bandwidth. Such an allocation is said to be efficient. It is also shown that there exists a unique efficient allocation in the entire feasible region. An iterative algorithm is developed to compute the efficient allocation employing its special properties. Numerical examples are presented to demonstrate how the algorithm works. Future extensions of this work are also discussed.Partially supported by NSERC of Canada through grants OGP14020 and STRIN-200.     

Self-aligned offset gated poly-Si TFTs with a floating sub-gate

We have fabricated a self-aligned offset-gated poly-Si thin film transistor (TFT) by employing a novel photoresist reflow process. The gate structure of the new device is consisted of two unique patterns: A main-gate and a sub-gate. The new fabrication method extends the gate-oxide over the offset region. With the assistance of the sub-gate and reflowed photoresist a self-aligned offset region is successfully obtained due to the offset oxide acting as an implantation mask. The poly-Si TFT with symmetrical offsets is easily fabricated and the new method does not require any additional offset mask step. Compared with the misaligned offset gated poly-Si TFTs, excellent symmetric electrical characteristics are obtained     

Electrical properties and positron annihilation study of (Ba<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ho<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>)TiO<Subscript>3</Subscript> ceramics

DC resistivity, dielectric constant, dielectric loss and positron annihilation spectra of (Ba_1−x Ho _x )TiO₃ ceramics have been measured as a function of holmium concentration x. It has been found that the DC resistivity of (Ba_1−x Ho _x )TiO₃ is strongly dependent on the Ho content: it decreases three orders of magnitude and reaches a minimum at x = 0.4%. Doping with 0.6% holmium increases the permittivity of BaTiO₃ by approximately three times (from ∼1,300 to ∼4,000), with only a slight increase in the corresponding dielectric loss. The local electron density and defect concentration estimated using positron annihilation technique conforms well to the features found in the dielectric and resistivity measurements. The results have been discussed in terms of a mixed compensation model.     

Preliminary<Emphasis Type="Italic">in vitro</Emphasis> and<Emphasis Type="Italic">in vivo</Emphasis> characterizations of a sol-gel derived bioactive glass-ceramic system

This study investigates quantitatively and qualitatively the sol-gel derived bioactive glass-ceramic system (BGS)—apatite-wollastonite (AW) type granules in the size range of 0.5–1 mm, as an effective graft material for bone augmentation and restoration. Scanning electron micrographs (SEM) of the sintered granules revealed the rough material surface with micropores in the range 10–30 μm. X-ray diffraction (XRD) pattern of the granules revealed the presence of crystalline phases of the hydroxyapatite and wollastonite, and the functional groups of the silicate and phosphates were identified by Fourier transform infrared spectroscopy (FT-IR). Thein vitro cell culture studies with L929 mouse fibroblast cell line showed very few cells adhered on the BGS disc after 24 h. This could be due to the highly reactive surface of the disc concomitant with the crystallization but not due to the cytotoxicity of the material, since the cellular viability (MTT assay) with the material was 80‰ Cytotoxicity and cytocompatibility studies proved that the material was non-toxic and biocompatible. After 12 weeks of implantation of the BGS granules in the tibia bone of New Zealand white rabbits, the granules were found to be well osteointegrated, as observed in the radiographs. Angiogram with barium sulphate and Indian ink after 12 weeks showed the presence of microcapillaries in the vicinity of the implant site implicating high vascularity. Gross observation of the implant site did not show any inflammation or necrosis. SEM of the implanted site after 24 weeks revealed good osteointegration of the material with the newly formed bone and host bone. New bone was also observed within the material, which was degrading. Histological evaluation of the bone healing with the BGS granules in the tibial defect at all time intervals was without inflammation or fibrous tissue encapsulation. After 2 weeks the new bone was observed as a trabeculae network around the granules, and by 6 weeks the defect was completely closed with immature woven bone. By 12 weeks mature woven bone was observed, and new immature woven bone was seen within the cracks of the granules. After 24 weeks the defect was completely healed with lamellar bone and the size of the granules decreased. Histomorphometrically the area percentage of new bone formed was 67.77% after 12 weeks and 63.37% after 24 weeks. Less bone formation after 24 weeks was due to an increased implant surface area contributed by the material degradation and active bone remodeling. The osteostimulative and osteoconductive potential of the BGS granules was established by tetracycline labelling of the mineralizing areas by 2 and 6 weeks. This sol-gel derived BGS granules proved to be bioactive and resorbable which in turn encouraged active bone formation.     

Kinetics of chlorination of tantalum pentoxide in mixture with sucrose carbon by chlorine gas

The mechanism and kinetics of β-Ta₂O₅ chlorination, mixed with sucrose carbon, have been studied by a thermogravimetric technique. The investigated temperature range was 500 °C to 850 °C. The reactants and reaction residues were analyzed by scanning electronic microscopy (SEM), X-ray diffraction (XRD), and Brunauer-Emmett-Teller method for surface area (BET). The effect of various experimental parameters was studied, such as carbon percentage, temperature, chlorine partial pressure, and flow, use of the multiple sample method, and carbon previous oxidation. The carbon percentage and previous treatment have an effect on the system reactivity. The temperature has a marked effect on the reaction rate. In the 500 °C to 600 °C temperature interval, the apparent activation energy is 144 kJ/mol of oxide, while at higher temperatures, the activation energy decreases. With high chorine partial pressures, the order of reaction is near zero. The kinetic contractile plate model, X=kt, considering carbon oxidation as the controlling stage, is the one with the best fit to the experimental data. A probable mechanism for the carbochlorination of β-Ta₂O₅ is proposed: (1) activation of chlorine on the carbon surface, (2) chlorination of Ta₂O₅, (3) oxidation of carbon, and (4) recrystallization of β-Ta₂O₅.