Crystal orientation of β-phase isotactic polypropylene induced by magnetic orientation of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide

Melt crystallization of isotactic polypropylene (iPP), containing crystallites of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide (DCNDCA) as a nucleating agent of the the β-phase iPP crystal, is carried out under a magnetic field (6 T) to obtain the alignment of the iPP crystal induced by magnetic alignment of DCNDCA. In a previous paper, DCNDCA was reported to undergo magnetic alignment in a liquid suspension. The obtained iPP sample exhibits alignment of the β-phase crystal with the c-axis aligned perpendicular to the magnetic field. The comparison of this alignment of iPP with the reported magnetic alignment of DCNDCA indicates that the β-phase crystal grows epitaxially on the DCNDCA crystal. The (330)_β plane of the iPP crystal lies on the bc-plane of the DCNDCA crystal in which the direction of the c-axis of the iPP coincides with the direction of the b-axis of the DCNDCA crystal.     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002     

FEATURE SOLID MODELING TOOL SYSTEM:FSMTS

In conformity with the principle of Design for Manufacture,feature-based design strate-(?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NCprograms”,obviously,“feature”is beyond the power of conventional solid modellers.Neverthe-less,substantial breakthrough has not been made in the solid modeling field,except“feature at-taching”or“feature recognizing”methods have been taken on.In this paper,the theory,concepts,system architecture,and algorithm principles of solid modeling tool system have beenrepresented.The practice of Feature Solid Modeling Tool System (FSMTS) developed atHuazhong University has proved that the tool may be a new foundation of Feature-Based Design.     

Embedded deterministic test for low-cost manufacturing

You have probably heard that BIST takes too long and its fault coverage is low, and that deterministic test requires too many patterns. This article shows how on-chip compression and decompression techniques provide high fault coverage with low test times.     

试论入世对中国氧化铝工业的影响

随着中国加入WTO，给企业带来了发展的机会，也带来了挑战。本文通过对中国氧化铝工业的现状及其与世界水平的差距的分析，阐明了入世后随着关税等贸易壁垒的消除，国内、国际市场的竞争更加激烈。明确指出了我国氧化铝工业面临的多重挑战，以及给中国氧化铝工业带来的机遇。强调充分利用WTO给企业创设的权利，借入世东风，促进我国氧化铝工业快速发展，只有发展，中国氧化铝工业才有出路。     

Continuous Separation of Inclusions from Aluminum Melt Flowing in a Circular Pipe using a High Frequency Magnetic Field

The continuous separation of inclusions from aluminum melt flowing in a circular pipe using a high frequency magneticfield was investigated both theoretically and experimentally The separation efficiency was calculated based on thetrajectory method and compared with experimental results. It is found that the separation efficiency is a functilnondimensional parameters t_i·d_p~2B_e~2/μ_fμ_eα~2 and α/δ.The effective way to improve the separation efficiency is to increasethe effective magnetic flux density and decrease the pipe radius. and the value of α/δ should be kept about 2 in orderto obtain the optimum separation efficiency.     

硅化腐植酸钠GFN-1的研制

针对目前生产腐植酸硅化产品原料受限的缺点,在大量试验的基础上,确定了一条以腐植酸和硅化剂为主要原料的生产工艺,合成了一种与有机硅腐植酸钾(OSAM-K)性能相当的硅化腐植酸钠产品GFN-1,对其常规性能指标和在清水及无固相聚合物钻井液体系中、在膨润土浆和低固相钻井液体系中应用指标,耐温性能进行了对比实验。实验结果表明,GFN-1作为钻井液添加剂,具有良好的降滤失、降黏、耐温及热稳定性,并兼有优良的控制页岩分散能力,其大多数应用性能相当于或略优于OSAM-K,作为替代品完全能够满足油田现场应用的需要。GFN-1的硅化原料性质稳定、来源广泛,生产工艺简单易行,产品质量稳定,具有较好的推广价值。     

Tb掺杂对纳米TiO_2光催化活性的影响

以溶胶-凝胶法制备了纳米TiO2和掺杂Tb的TiO2(Tb-TiO2),用X射线衍射、示差扫描量热、热重分析、红外光谱和荧光光谱等技术对纳米TiO2和Tb-TiO2的结构进行了表征;考察了以纳米TiO2及Tb-TiO2为催化剂光催化氧化环己烷合成环己酮和环己醇的情况。表征结果表明,掺杂Tb后明显抑制了TiO2中锐钛矿相向金红石相的转变,提高了TiO2催化剂的热稳定性,晶格发生了膨胀现象,晶格膨胀可有效降低光生载流子的复合几率,减小晶粒尺寸,提高光催化活性;光催化氧化环己烷的实验结果表明,与TiO2催化剂相比,Tb-TiO2催化剂的环己烷转化率和环己酮、环己醇的选择性大幅度提高,表明Tb-TiO2催化剂的光催化活性和光催化效率提高。     

海水注入开发中剩余油饱和度评价研究

剩余油饱和度评价是油田水淹层测井评价中的重点和难点。当油田发生水淹后,储层的润湿性、地层水电阻率都将发生较大的变化,因此剩余油饱和度评价所需的处理参数必须重新确定。以南中国海某河流相沉积油田的储层在水淹后的剩余油饱和度评价中的关键参数研究为例,通过模拟油藏条件下的岩电实验和地层混合水矿化度与实际含水率的关系,研究探索求取剩余油饱和度评价关键参数的有效方法,应用中与实际生产符合较好,为此类开发油田的剩余油饱和度的精确评价奠定了基础。