X-ray or UV adjustment of MOS threshold voltage: Analytical and numerical modeling

A model is formulated that describes how radiation-induced charge accumulates in the gate oxide of a MOS structure and how it decays through tunneling and thermal emission. The model is used in a numerical analysis of the x-ray or UV adjustment of threshold voltage in MOS-circuit manufacture. The limits of this process technique are evaluated.     

Using the magneto-optical Kerr effect to study magnetization processes in two-dimensional magnonic crystals based on YIG thin films

The magneto-optical Kerr effect for red (628 nm) and green (532 nm) light is used to study magnetization processes in 2D magnonic crystals obtained by etching pits with the diameter D ≈ 32 μm to a depth of t ≤ 2 μm in a 16.1-μm-thick film of yttrium iron garnet (YIG). Hysteresis loops obtained in the case of the inplane crystal magnetization at 628 nm are characterized by lower saturation fields H _s and higher remanent magnetizations than those obtained at 532 nm, a result that is attributed to different absorption coefficients of the YIG film at these wavelengths. This difference between the magnetization curves reflects the fact that the magnonic-crystal surface probed with the green light makes a greater contribution to the magneto-optical Kerr effect. Therefore, the green light is more sensitive to the demagnetizing fields, which govern magnetization processes in the magnonic crystals.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Analytic models for the latency and steady-state throughput of TCP Tahoe, Reno, and SACK

Continuing the process of improvements made to TCP through the addition of new algorithms in Tahoe and Reno, TCP SACK aims to provide robustness to TCP in the presence of multiple losses from the same window. In this paper we present analytic models to estimate the latency and steady-state throughput of TCP Tahoe, Reno, and SACK and validate our models using both simulations and TCP traces collected from the Internet. In addition to being the first models for the latency of finite Tahoe and SACK flows, our model for the latency of TCP Reno gives a more accurate estimation of the transfer times than existing models. The improved accuracy is partly due to a more accurate modeling of the timeouts, evolution of cwnd during slow start and the delayed ACK timer. Our models also show that, under the losses introduced by the droptail queues which dominate most routers in the Internet, current implementations of SACK can fail to provide adequate protection against timeouts and a loss of roughly more than half the packets in a round will lead to timeouts. We also show that with independent losses SACK performs better than Tahoe and Reno and, as losses become correlated, Tahoe can outperform both Reno and SACK.     

A VQ-based blind image restoration algorithm

Learning-based algorithms for image restoration and blind image restoration are proposed. Such algorithms deviate from the traditional approaches in this area, by utilizing priors that are learned from similar images. Original images and their degraded versions by the known degradation operator (restoration problem) are utilized for designing the VQ codebooks. The codevectors are designed using the blurred images. For each such vector, the high frequency information obtained from the original images is also available. During restoration, the high frequency information of a given degraded image is estimated from its low frequency information based on the codebooks. For the blind restoration problem, a number of codebooks are designed corresponding to various versions of the blurring function. Given a noisy and blurred image, one of the codebooks is chosen based on a similarity measure, therefore providing the identification of the blur. To make the restoration process computationally efficient, the principal component analysis (PCA) and VQ-nearest neighbor approaches are utilized. Simulation results are presented to demonstrate the effectiveness of the proposed algorithms.     

Effect of the Distribution of Manganese Ions on the Properties of Mn-Doped (Ba,Y)TiO3 PTCR Ceramics

The electrical properties and microstructure of (Ba,Y)TiO₃ PTCR ceramics were studied. The results indicate that the Mn ions increase the intergranular barrier height and produce a high-resistance layer on the grain surface. The temperature-dependent resistances of the grain bulk, surface layer, and grain boundaries, the temperature coefficient of resistance, and the magnitude of the varistor effect were assessed as a function of Mn content.     

On trading wavelengths with fibers: a cost-performance based study

We consider the effect of multiple fibers on wavelength division multiplexing networks without wavelength conversion. We study networks with dynamic wavelength routing and develop accurate analytical models to compare various possible options using single- and multiple-fiber networks. We use results of an analytical model and simulation-based studies to evaluate the blocking performance and cost of multifiber networks. The number of fibers required providing high performance in multifiber networks and their costs are compared. A case is made for using multiple fibers in each link with fewer wavelengths instead of using a single fiber with many wavelengths. In particular, we show that a network with four fibers per link and with four wavelengths on each fiber without any wavelength conversion on any node yields similar same performance as the networks with one fiber per link and 16 wavelengths per fiber on each link and with full wavelength conversion capability on all nodes. In addition, the multifiber network may also offer the cost advantage depending on the relative cost of components. We develop a parametric cost model to show that multiple fibers in each link are an attractive option. Finally, such multifiber networks also has fault tolerance, with respect to a single fiber failure, already built into the system.     

Derivation of a second-order switching surface in the boundary control of buck converters

A second-order switching surface in the boundary control of buck converters is derived in this letter. The formulated switching surface can make the overall converter exhibit better steady-state and transient behaviors than the one with a first-order switching surface. The switching surface is derived by estimating the state trajectory movement after a switching action, resulting in a high state trajectory velocity along the switching surface. This phenomenon accelerates the trajectory moving toward the target operating point. The proposed control scheme has been successfully applied to a 120-W buck converter. The large-signal performance and a comparison with the first-order switching surface have been studied.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Static energy reduction techniques for microprocessor caches

Microprocessor performance has been improved by increasing the capacity of on-chip caches. However, the performance gain comes at the price of static energy consumption due to subthreshold leakage current in cache memory arrays. This paper compares three techniques for reducing static energy consumption in on-chip level-1 and level-2 caches. One technique employs low-leakage transistors in the memory cell. Another technique, power supply switching, can be used to turn off memory cells and discard their contents. A third alternative is dynamic threshold modulation, which places memory cells in a standby state that preserves cell contents. In our experiments, we explore the energy and performance tradeoffs of these techniques. We also investigate the sensitivity of microprocessor performance and energy consumption to additional cache latency caused by leakage-reduction techniques.