Detection of wide-band E-M signals emitted from partial dischargeoccurring in GIS using wavelet transform

Recently, diagnostic techniques have been investigated to detect a partial discharge (PD) associated with a dielectric material defect in a high-voltage electrical apparatus. Gas insulated switchgear (GIS) is an important equipment in a substation, it is highly desirable to measure a partial discharge (PD) occurring in GIS which is a symptom of an insulation breakdown. As it is important to develop a noncontact method for detecting the insulation fault, this paper proposes a new method to detect the wide-band electromagnetic (E-M) wave emitted from PD using the Wavelet transform. The Wavelet transform provides a direct quantitative measure of spectral content, “dynamic spectrum”, in the time-frequency domain. This paper experimentally shows the “dynamic spectrum” of the wide-band E-M wave emitted from PD in the time-frequency domain. This method is shown to be useful for detecting the symptom of the insulation breakdown occurring in GIS     

Use of multivariate analysis for the improvement in prediction accuracy of bacterial aerobic plate count by flow cytometry

Flow cytometry (FCM) and aerobic plate count (APC) by the culture method were performed on green tea samples spiked with Escherichia coli type strain NCTC9001 (ATCC11775) solutions of different concentrations. In FCM, fluorescence signals from multiple stained bacteria and other fluorophores are detected using detector channels, and recorded as events with a voltage at each channel. FCM data were analyzed in two ways: conventional and multivariate analysis. In the former, the number of events with voltages larger than the defined threshold values was regarded as the predicted APC. In the latter, voltage histograms of all channels were obtained and merged horizontally to serve as explanatory variables. Then a partial least squares regression (PLSR) model was built to predict APC from the histogram data. The coefficient of determination (R²) and the root mean square error (RMSE) between APC by the culture method and that predicted by conventional FCM were 0.916 and 1.08 cfu/ml². The APC values predicted by the PLSR model and those measured were in good agreement with R² of 0.982 and RMSE of 0.417 cfu/ml, which verified the potential of the proposed method for improving APC prediction accuracy by FCM.     

RADIOLYTIC DEGRADATION OF A CROWN ETHER FOR EXTRACT ABILITY OF STRONTIUM

ABSTRACT

Dicyclohexano- 18-crown-6 (DC18C6), dissolved in chloroform, 1-octanol, toluene or cyclohexane, was irradiated by ⁶⁰Co γ-rays. Radiolytic destruction of DC18C6, measured by gas chromatography, decreased in the order: chloroform > cyclohexane > 1-octanol > toluene. Distribution coefficients in the solvent extraction of strontium from nitric acid solution were measured. These distribution coefficients were minimally affected by γ-irradiation in toluene solution, but decreased with the absorbed dose in chloroform solution. It was suggested that the distribution coefficient for the liquid-liquid extraction system was influenced by radiolytic products. The effect of radiolytic products on the distribution coefficients was evaluated by considering DC18C6 remaining in the organic phase after irradiation. The distribution coefficient measured for the organic phase with radiolytic products was larger than that without radiolytic products. The radiolytic products were thus shown to contribute to the increase in the distribution coefficient.     

Effect of different copper fillers on the electrical resistivity of conductive adhesives

The effects of different copper fillers with different morphology and particle size have been studied in terms of electrical resistivity and thermal stability on the electrically conductive adhesives. The copper fillers used in this study were prepared by wet chemical reduction, electrolytic and gas atomization method, respectively. The as cured ECAs filled with different type of Cu fillers showed significant difference in electrical resistivity. Cu filler with smaller particle size showed higher packing density and larger surface area, which would enhance formation of conductive channels and increased conductive network in the ECAs, leading to a lower electrical resistivity. In addition, thermal stability of the ECAs were investigated under high temperature exposure at 125 °C and high humidity aging at 85 °C/85% RH for 1,000 h. Results showed that ECAs with Cu fillers of relatively small particle size and rough particle surface have excellent thermal stability due to enhanced adhesion and contact area between Cu fillers and the polymer matrix. A very low resistivity at an order of magnitude of 10^?4 ?? cm could be maintained for these ECAs after 1,000 h at 125 and 85 °C/85% RH.     

Ultrasonic-Assisted Soldering of 5056 Aluminum Alloy Using Quasi-Melting Zn-Sn Alloy

To obtain sound butt-joints of 5056 aluminum alloy rods, ultrasonic-assisted soldering was conducted using Zn-18Sn and Zn-60Sn alloys. Each solder foil was inserted between rods of 5056 aluminum alloy. Ultrasonic vibration was propagated to faying surfaces at soldering temperatures below the liquidus temperature of the solder alloys, and then the samples were air cooled to room temperature. The optimum vibration time at the soldering temperature must be more than 2 seconds to have complete wetting and less than 4 seconds to avoid excessive dissolution of the 5056 alloy. The 5056 alloy joints soldered using quasi-melting. Zn-Sn alloys showed greater strength than the joints soldered at the temperatures over its respective liquidus temperature. As the soldering temperature was increased, the increased formation of the intermetallic compound Mg₂Sn or phases containing Mg generated by dissolution of 5056 into the solder layer decreased the joint strength. Ultrasonic-assisted soldering at an optimum temperature between solidus and liquidus of the Zn-Sn alloys is an important consideration for producing sound joints with sufficient strength.     

Heat transfer characteristics of a reservoir embedded loop heat pipe (Heat transfer characteristics of a deployable radiator for use on the ETS‐VIII satellite while in orbit)

As heat generation in satellites increases, ensuring that they are provided with sufficient radiator panel area is an important problem. Deployable radiators, with radiator panels that are deployed post‐launch in space to increase the satellite's effective radiator panel area of the satellite, are becoming an important thermal control technology. A reservoir embedded loop heat pipe (RELHP) is used in deployable radiators as a heat transport device. A deployable radiator of this type was mounted on the ETS‐VIII satellite, which was launched on December 18, 2006 and injected into a geostationary orbit. The satellite is still operating without any significant issues over two years later. This paper investigates the heat transport characteristics of an RELHP system used in a deployable radiator in a geostationary orbital environment. This system can be successfully started up in a micro gravity environment. We also found that the sub‐cooling region is shorter in a micro gravity environment than in a terrestrial gravity environment, because there is less heat leakage into the reservoir in a micro gravity environment. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20346     

Low-temperature thermionic emission from nitrogen-doped nanocrystalline diamond films on n-type Si grown by MPCVD

Temperature-dependent emission current–voltage measurements were carried out for nitrogen (N)-doped nanocrystalline diamond (NCD) films grown on n-type Si substrates by microwave plasma-assisted chemical vapor deposition (MP-CVD). Low threshold temperature (~ 260 °C) and low threshold electric field (~ 5 × 10^− 5 V/µm) were observed. Both the temperature dependence and the electric field dependence have shown that the obtained emission current was based on electron thermionic emission from N-doped NCD films. We have also studied the relation between nitrogen concentration and the saturation emission current. The saturation current obtained was as high as 1.4 mA at 5.6 × 10^− 3 V/µm at 670 °C when the nitrogen concentration was 2.4 × 10²⁰ cm^− 3. Low value of effective work function (1.99 eV) and relatively high value of Richardson constant (~ 70) were estimated by well fitting to Richardson–Dushman equation. The results of smaller φ and larger A′ suggest that N-doped NCD has great possibility of being a highly efficient thermionic emitter material.     

Thermal performance of a packed bed reactor for a high‐temperature chemical heat pump

The thermal performance of a chemical heat pump that uses the reaction system of calcium oxide/lead oxide/carbon dioxide, which is developed for utilization of high‐temperature heat above 800°C, is studied experimentally. The thermal performance of a packed‐bed reactor of a calcium oxide/carbon dioxide reaction system, which stores and transforms a high‐temperature heat source in the heat pump operation, is examined under various heat pump operation conditions. The energy analysis based on the experiment shows that it is possible to utilize high‐temperature heat with this heat pump. This heat pump can store heat above 850°C and then transform it into a heat above 900°C under an approximate atmospheric pressure. An applied system that combines the heat pump and a high‐temperature process is proposed for high‐efficiency heat utilization. The scale of the heat pump in the combined system is estimated from the experimental results. Copyright © 2001 John Wiley & Sons, Ltd.