Oxygen evolution anodes composed of anodically deposited Mn-Mo-Fe oxides for seawater electrolysis

Preparation of anodes for oxygen evolution in seawater electrolysis was carried out. Manganese-molybdenum double oxides, Mn_1−xMo_xO_2+x, prepared by anodic deposition from MnSO₄-Na₂MoO₄ solutions showed the 100% oxygen evolution efficiency at a current density of 1000 A m⁻² in 0.5 M NaCl at 30 °C and pH 12, but an increase in solution temperature resulted in dissolution of the oxides as molybdate and permanganate ions. In order to increase the stability of the electrodes at higher temperatures the addition of iron to the manganese-molybdenum oxides was performed by anodic deposition in MnSO₄-Na₂MoO₄-FeNH₄(SO₄)₂ solutions. The electrodes thus prepared showed the 100% oxygen evolution efficiency at 1000 A m⁻² in 0.5 M NaCl at 30-90 °C, when proper amounts of molybdenum and iron were contained. The iron addition also enhanced the oxygen evolution efficiency. The electrodes were not composed of oxide mixtures but triple oxides, Mn_1−x−yMo_xFe_yO_2+x−0.5y, consisting of Mn⁴⁺, Mo⁶⁺ and Fe³⁺. The formation of the triple oxides seemed responsible for enhancement of both oxygen evolution efficiency and stability.     

Free primary alcohols in oils and waxes from germs,kernels and other components of nuts,seeds, fruits and cereals

The composition of free primary alcohols in oils and waxes obtained from the germ, kernel, seed coat, shell and skin (peel) of various nuts, seeds, fruits and cereals and from the chrysalis of silkworm was examined. These alcohols are usually present in small amounts, along with large quantities of hydrocarbons, esters and glycerides in oils and waxes. Thus, it is necessary to remove hydrocarbons, esters and glycerides to analyze the alcohols. We found that preparative reverse-phase thin-layer chromatography (TLC) was the best way to isolate alcohols from oils and waxes. Gas liquid chromatography (GLC) then detected hexacosanol, octacosanol and triacontanol in the oils and waxes. Octacosanol usually was the predominant alcohol. Relationships between the organs from nuts, seeds, fruits and cereals and the contents of octacosanol are suggested. For example, degermed kernels contained two times more octacosanol than the germ, and the skin coat and shell contained one-half and one-fortieth the octacosanol of the germ, respectively.     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Application of pulse discharge sintering (PDS) technique to rapid synthesis of Ti3SiC2 from Ti/Si/C powders

To synthesize Ti₃SiC₂ samples, pulse discharge sintering (PDS) technique was utilized to sinter elemental powders of Ti/Si/C with stoichiometric and off-stoichiometric ratios in a temperature range of 1200–1500 °C. The results showed that high purity Ti₃SiC₂ could not be obtained from the Ti/Si/C powder with molar ratio of 3:1:2, and Ti₃SiC₂ preferred to form at relatively low sintering temperature for a short time. When 5Ti/2Si/3C and 3Ti/1.5Si/2C powders were sintered for 15 min, the TiC content was respectively decreased to 6.4 and 10 wt.% at 1250–1300 °C. The corresponding relative density of the samples sintered from 5Ti/2Si/3C powder was calculated to be as high as 99% at the temperature above 1300 °C. It is suggested that low-temperature rapid synthesis of Ti₃SiC₂ would be possible through the PDS technique, provided that the composition of the starting powders should be adjusted to be off-stoichiometric ratio from 3:1:2.     

Anodic characteristics of amorphous ternary palladium-phosphorus alloys containing ruthenium,rhodium, iridium,or platinum in a hot concentrated sodium chloride solution

Amorphous ternary palladium-based alloys containing platinum group metals as an additional element were prepared by rapid quenching from the molten state and their anodic characteristics were investigated in a 4 mol dm^?3 NaCl solution of pH 4 and 80° C. The amorphous alloys containing sufficient quantities of rhodium, platinum or iridium were passivated by anodic polarization and their corrosion rates at high current densities in the chlorine evolution region were extremely low. This fact was attributed to the formation of a highly protective passive film due to both the transformation to the amorphous structure and the addition of rhodium, platinum or indium. The electrocatalytic activities for chlorine evolution of amorphous alloys were higher than those of pure platinum group metals except palladium. In particular, the amorphous Pd₄₁Ir₄₀P₁₉ alloy had the desired stable, high electrocatalytic activity for chlorine evolution and the high overvoltage for oxygen evolution.     

Novel CO2 Absorbents Using Lithium-Containing Oxide

We have discovered a series of lithium-containing oxides that immediately react with ambient carbon dioxide (CO₂) up to 700°C. The products react and return reversibly to the oxides at a temperatures higher than about 700°C. The absorption capacity surpasses that of other CO₂ absorbents by a factor of 10. Utilizing these absorbents, the possibility of a CO₂ separation system that operates at around 500°C is proposed. It is generally believed that a CO₂ separation process operable at temperatures higher than 500°C has the special benefit of a small energy penalty. Moreover, the absorption also proceeds at ambient temperature in the atmospheric environment. This property offers the possibility of many other applications, such as air cleaners or cartridges. Therefore, we think these materials have the potential to make a valuable contribution to the realization of CO₂ emission control.     

Additional kernel observer: privilege escalation attack prevention mechanism focusing on system call privilege changes

International Journal of Information Security - Cyberattacks, especially attacks that exploit operating system vulnerabilities, have been increasing in recent years. In particular, if administrator...     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.