Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Application of pulse discharge sintering (PDS) technique to rapid synthesis of Ti3SiC2 from Ti/Si/C powders

To synthesize Ti₃SiC₂ samples, pulse discharge sintering (PDS) technique was utilized to sinter elemental powders of Ti/Si/C with stoichiometric and off-stoichiometric ratios in a temperature range of 1200–1500 °C. The results showed that high purity Ti₃SiC₂ could not be obtained from the Ti/Si/C powder with molar ratio of 3:1:2, and Ti₃SiC₂ preferred to form at relatively low sintering temperature for a short time. When 5Ti/2Si/3C and 3Ti/1.5Si/2C powders were sintered for 15 min, the TiC content was respectively decreased to 6.4 and 10 wt.% at 1250–1300 °C. The corresponding relative density of the samples sintered from 5Ti/2Si/3C powder was calculated to be as high as 99% at the temperature above 1300 °C. It is suggested that low-temperature rapid synthesis of Ti₃SiC₂ would be possible through the PDS technique, provided that the composition of the starting powders should be adjusted to be off-stoichiometric ratio from 3:1:2.     

Anodic characteristics of amorphous ternary palladium-phosphorus alloys containing ruthenium,rhodium, iridium,or platinum in a hot concentrated sodium chloride solution

Amorphous ternary palladium-based alloys containing platinum group metals as an additional element were prepared by rapid quenching from the molten state and their anodic characteristics were investigated in a 4 mol dm^?3 NaCl solution of pH 4 and 80° C. The amorphous alloys containing sufficient quantities of rhodium, platinum or iridium were passivated by anodic polarization and their corrosion rates at high current densities in the chlorine evolution region were extremely low. This fact was attributed to the formation of a highly protective passive film due to both the transformation to the amorphous structure and the addition of rhodium, platinum or indium. The electrocatalytic activities for chlorine evolution of amorphous alloys were higher than those of pure platinum group metals except palladium. In particular, the amorphous Pd₄₁Ir₄₀P₁₉ alloy had the desired stable, high electrocatalytic activity for chlorine evolution and the high overvoltage for oxygen evolution.     

Additional kernel observer: privilege escalation attack prevention mechanism focusing on system call privilege changes

International Journal of Information Security - Cyberattacks, especially attacks that exploit operating system vulnerabilities, have been increasing in recent years. In particular, if administrator...     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.     

Materials for global carbon dioxide recycling

CO₂ emissions, which induce global warming, increase with the development of economic activity. It is impossible to decrease the CO₂ emissions by suppression of the economic activity. Global CO₂ recycling can solve this problem. The global CO₂ recycling consists of three district: The electricity is generated by solar cells on deserts. At desert coasts, the electricity is used for H₂ production by seawater electrolysis and H₂ is used for CH₄ production by the reaction with CO₂. CH₄ which is the main component of liquefied natural gas is liquefied and transported to energy consuming districts where CO₂ is recovered, liquefied and transported to the desert coasts. A CO₂ recycling plant for substantiation of our idea has been built on the roof of the Institute for Materials Research in 1996. Key materials necessary for the global CO₂ recycling are the anode and cathode for seawater electrolysis and the catalyst for CO₂ conversion. All of them have been tailored by us. They have very high activity and selectivity for necessary reactions in addition to excellent durability. A pilot plant consisting of minimum units in an industrial scale is going to be built in three years.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Bright-field scanning confocal electron microscopy using a double aberration-corrected transmission electron microscope

Scanning confocal electron microscopy (SCEM) offers a mechanism for three-dimensional imaging of materials, which makes use of the reduced depth of field in an aberration-corrected transmission electron microscope. The simplest configuration of SCEM is the bright-field mode. In this paper we present experimental data and simulations showing the form of bright-field SCEM images. We show that the depth dependence of the three-dimensional image can be explained in terms of two-dimensional images formed in the detector plane. For a crystalline sample, this so-called probe image is shown to be similar to a conventional diffraction pattern. Experimental results and simulations show how the diffracted probes in this image are elongated in thicker crystals and the use of this elongation to estimate sample thickness is explored.