Measurement method of plasma current and density in atmospheric pressure plasma jet

We present a measurement method of the plasma current and density in an atmospheric‐pressure plasma generated using a quartz tube, helium gas, and copper foil electrode by applying a high RF voltage. The plasma in the form of a bullet is released as a plume or jet into the atmosphere. To study the characteristics of the atmospheric‐pressure plasma, the plasma current is measured using a current probe, and the drift velocity of plasma plume is measured using a photodetector. The current of the plasma plume is estimated by subtracting the ground line current from the power line current in the circuit. The density of plasma plume n is estimated from the plasma plume current I and the drift velocity v as I = envS, where S is the cross section of plasma plume. The density of the released plasma into the atmosphere is estimated as ∼10¹⁸ m⁻³ by the method. © 2015 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Selective preparation of oligomeric naphthylene ether and its applications to epoxy resin for silicon carbide power semiconductor device materials

In this study, a novel method for selective synthesis of naphthylene ether trimers by self‐condensation of 2,7‐dihydroxynaphthalene in the presence of catalytic amount of potassium hydroxide was reported. An epoxy resin from the trimers was prepared and properties of the cured epoxy resin were examined. The cured resin showed not only good physical thermal stability, such as high glass transition temperature and low thermal expansion coefficient, but also good chemical thermal stability like high thermal decomposition temperature. Additionally, low moisture absorption of the cured resin was confirmed. From these results, the newly prepared epoxy resin with naphthylene ether skeletons was considered to be suitable for advanced applications such as silicon carbide power semiconductor device. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43339.     

Characterization of alternative plasticizers in poly(vinyl chloride) sheets for blood containers

This study aimed to optimize the ratio of dioctyl 4‐cyclohexene‐1,2‐dicarboxylate (DOTH) and di‐isononyl‐cyclohexane‐1,2‐dicarboxylate (DINCH^®) for use as plasticizers in poly(vinyl chloride) (PVC) sheets. We also evaluated the biological safety of DOTH for its potential to be part of a safe PVC‐based blood container. The suppression of hemolysis in mannitol‐adenine‐phosphate / red cell concentrates (MAP/RCC) with DOTH/(DINCH^®‐PVC) sheets and the elution of plasticizers from the sheets increased with higher DOTH compositions. The properties of the PVC sheet containing DOTH and DINCH^® in the ratio of 25:33 parts against PVC 100 parts as a weight were almost identical to the PVC sheet made of di(2‐ethylhexyl) phthalate. From a subchronic toxicity test, DOTH did not show any adverse effects on all organs, including the testes, epididymis, liver, and kidneys. The no‐observed‐adverse‐effect level was 300 mg/kg body weight/day in a rat. These results suggest that DOTH/DINCH^® (25:33) is a promising candidate for the replacement of di(2‐ethylhexyl) phthalate in blood containers. J. VINYL ADDIT. TECHNOL., 22:520–528, 2016. © 2015 Society of Plastics Engineers     

Photoacoustic Spectroscopy of Some Energetic Materials

To find an effective laser source to ignite energetic materials, the absorption spectra of some energetic materials are obtained by means of a photoacoustic spectroscopy (PAS). In this experiment, PAS covers the wavelength region of 400 nm-1600 nm in which no other conventional method can take absorption spectra for powdered energetic materials. Photoacoustic spectra of 18 energetic materials are reported. In general, energetic materials tested showed peaks in 600 nm–800 nm and 1400 nm–1600 nm ranges. It is found that the energy required to initiate explosives in the case of ruby laser initiation were correlated with their photoacoustic signal intensities.     

Kinetic Study of the Prooxidant Effect of α-Tocopherol. Hydrogen Abstraction from Lipids by α-Tocopheroxyl Radical

A kinetic study of the prooxidant effect of α-tocopherol was performed. The rates of allylic hydrogen abstraction from various unsaturated fatty acid esters (ethyl stearate 1, ethyl oleate 2, ethyl linoleate 3, ethyl linolenate 4, and ethyl arachidonate 5) by α-tocopheroxyl radical in toluene were determined, using a double-mixing stopped-flow spectrophotometer. The second-order rate constants (k _p) obtained are <1 × 10⁻² M⁻¹ s⁻¹ for 1, 1.90 × 10⁻² M⁻¹ s⁻¹ for 2, 8.33 × 10⁻² M⁻¹ s⁻¹ for 3, 1.92 × 10⁻¹ M⁻¹ s⁻¹ for 4, and 2.43 × 10⁻¹ M⁻¹ s⁻¹ for 5 at 25.0 °C. Fatty acid esters 3, 4, and 5 contain two, four, and six –CH₂– hydrogen atoms activated by two π-electron systems (–C=C–CH₂–C=C–). On the other hand, fatty acid ester 2 has four –CH₂– hydrogen atoms activated by a single π-electron system (–CH₂–C=C–CH₂–). Thus, the rate constants, k _abstr/H, given on an available hydrogen basis are k _p/4 = 4.75 × 10⁻³ M⁻¹ s⁻¹ for 2, k _p/2 = 4.16 × 10⁻² M⁻¹ s⁻¹ for 3, k _p/4 = 4.79 × 10⁻² M⁻¹ s⁻¹ for 4, and k _p/6 = 4.05 × 10⁻² M⁻¹ s⁻¹ for 5. The k _abstr/H values obtained for 3, 4, and 5 are similar to each other, and are by about one order of magnitude higher than that for 2. From these results, it is suggested that the prooxidant effect of α-tocopherol in edible oils, fats, and low-density lipoproteins may be induced by the above hydrogen abstraction reaction.     

Reduction and unusual recovery in the reversible hydrogen storage capacity of V1−xTix during hydrogen cycling

The effect of the vanadium content on the cyclic stability of V–Ti binary alloys was investigated. V_1−xTi_x, x = 0.2 and 0.5 samples were hydrogenated and dehydrogenated at 410 K and 553 K respectively, for more than 100 times. During hydrogen cycling, reduction in the reversible hydrogen storage capacity was clearly observed from both samples. No prominent V-effect was found. In fact, the reduction rates of two samples were similar; both samples showed a ∼25% reduction in the reversible hydrogen storage capacity after 100 cycles. In addition, the shape of the pressure–composition-isotherm (PCT) curves was significantly altered over the testing cycle period; the absorption and desorption plateaus got markedly inclined and the hysteresis became evidently smaller. We found that even after the hydrogen storage capacity of V_1−xTi_x was significantly reduced, at low enough temperature V_1−xTi_x was able to absorb hydrogen as much as it did at the first cycle. Furthermore, the reversible hydrogen storage capacity of V_0.8Ti_0.2 at 410 K was recovered to a certain degree after hydrogenating the sample at low temperatures.     

Low cycle fatigue behaviors of elbow pipe with local wall thinning

Low cycle fatigue tests were conducted using 100A elbow specimens made of STPT410 carbon steel with local wall thinning. Local wall thinning by erosion/corrosion was simulated by machined pipe wall thinning. The local wall thinning areas were located at three different areas, called extrados, crown and intrados. The elbow specimens were subjected to cyclic in-plane bending under displacement control without internal pressure. The effects of eroded conditions, such as eroded ratio, eroded angle and position, on the low cycle fatigue behavior and fatigue life were discussed by using experimental results and finite element analyses. Also the location of crack initiation and the crack growth direction could be predicted by three dimensional elasto-plastic finite element analyses. In addition, the safety margin of eroded elbows against seismic loading was discussed by comparing the fictitious stress of elbows with the allowable stress limit demanded by the design code.     

Investigation for Necessity of Dispersivity and Tortuosity in the Dusty Gas Model for a Binary Gas System in Soil

Diffusion, dispersion, and advection are important processes in multi-gas systems in soils. To date, both Fick's model and the Dusty Gas (DG) model have been used to model the movement of gases in these systems. Dispersion is included in the dispersion-advection equation with Fick's Model for the movement of gases in gas-phase of soil, yet the movement of gases in multi-component gas-soil systems is considered to be expressed more accurately by the DG model than by Fick's model. However to date, no study has investigated the necessity of considering dispersion in the Dusty Gas (DG) model. We carried out column experiments for nitrogen-methane, nitrogen-carbon dioxide, and carbon dioxide-methane binary gas systems in sandy soil, and also did simulations on the same systems using both Fick's model and the DG model. A comparison of the results of the column experiments with our simulations confirmed that there was no need to consider the dispersion in the advection-diffusion equations with the DG model when the velocity of gas was 0.05-0.4 cm/s in Toyoura sand. Furthermore, our experiments and simulations with the DG model showed that, rather than dispersion, tortuosity should be taken into account in application of the DG model to the above condition.