Resistance Degradation in Y(Cr,Mn)O3–Y2O3 Composite NTC Ceramics in Hostile Environments

A series of composite, negative temperature coefficient (NTC) ceramics were carefully processed with compositions based on the Y(Cr,Mn)O₃+Y₂O₃ system and these were investigated for resistance stability in hostile environments. This specific system is of interest for high-temperature automobile thermistors, however either through the processing or in use of these, materials can be exposed to reducing atmospheres at temperatures around 900°–1000°C. The thermochemical processes at intermediate temperatures and low     <10⁻¹⁰atm can influence the resistance of the given ceramics. Through an impedance analysis it is determined that the resistance increase is associated primarily with a grain boundary resistance increase. The grain and grain boundary elements are modeled through parallel constant phase element and resistance equivalent circuits connected in series. Possible origins of the defect chemistry being controlled through high-temperature processes at the sintering are partial Schottky reactions that are compensated through a superoxidation reaction on cooling and aging. The reduction process reversed the superoxidation reaction and transited the grain boundary surfaces to ionically compensated B-site vacancies with oxygen vacancies.     

Sample preparation of GaN-based materials on a sapphire substrate for STEM analysis

In this work, a detailed TEM sample preparation recipe based on a wedge polishing technique for GaN-based materials is presented. The obtained samples have atomically flat surfaces without any obvious surface damages such as the formation of amorphous layers. A composition estimation of Al(x)Ga(1-x)N from Z-contrast STEM imaging is carried out using these samples. The results are in good accord with the nominal composition.     

Use of mild-heat treatment following high-pressure processing to prevent recovery of pressure-injured Listeria monocytogenes in milk

This study examined the inactivation of Listeria monocytogenes in milk by high-pressure processing (HPP) and bacterial recovery during storage after HPP. We developed a technique to inhibit the bacterial recovery during storage after HPP (550 MPa for 5 min) using a mild-heat treatment (30-50 degrees C). Various mild-heat treatments were conducted following HPP to investigate the condition on which the bacterial recovery was prevented. Immediately after HPP of 550 MPa at 25 degrees C for 5 min, no L. monocytogenes cells were detected in milk regardless of the inoculum levels (3, 5, and 7 log(10)CFU/ml). However, the number of L. monocytogenes cells increased by >8 log(10)CFU/ml regardless of the inoculum levels after 28 days of storage at 4 degrees C. Significant recovery was observed during storage at 25 degrees C; the bacterial number increased by >8 log(10)CFU/ml after 3 days of storage in the case of an initial inoculum level of 7 and 5 log(10)CFU/ml. Even in the case of an initial inoculum level of 3 log(10)CFU/ml, the bacterial number reached the level of 8 log(10)CFU/ml after 7 days of storage. No bacterial recovery was observed with storage at 37 degrees C for 28 days. Milk samples were treated by various mild-heat treatments (30-50 degrees C for 5-240 min) following HPP of 550 MPa at 25 degrees C for 5 min, and then stored at 25 degrees C for 70 days. The mild-heat treatment (e.g., 37 degrees C for 240 min or 50 degrees C for 10 min) inhibited the recovery of L. monocytogenes in milk after HPP. No recovery of L. monocytogenes in milk was observed during 70-day storage at 25 degrees C in samples that received mild-heat treatments such as mentioned above following HPP (550 MPa for 5 min). Moreover, the mild-heat treatment conditions (temperature and holding time) required to inhibit the recovery of L. monocytogenes in milk was modelled using a logistic regression procedure. The predicted interface of recovery/no recovery can be used to calculate the mild-heat treatment condition to control bacterial recovery during storage at 25 degrees C after HPP (550 MPa for 5 min). The results in this study would contribute to enhance the safety of high-pressure-processed milk.     

Dynamic profile calculation of deposition resolution by high-energy electrons in electron-beam-induced deposition

The effect of the accelerating voltage of incident electrons on the resolution of electron-beam-induced deposition was investigated by a dynamic Monte Carlo profile simulator which includes the electron scattering in the already grown deposit structure. By simulating the deposition at two different accelerating voltages of 20 and 200 kV with an idealistic zero-diameter incident probe on a bulk substrate, it was revealed that the smaller size structures were attainable by 200 keV than by 20 keV. The effect of the substrate was also argued by comparing the above results with the simulation results obtained for a point-like starting substrate. Surprisingly, the shapes of the deposits grown on bulk substrates were reproduced well by the simulations starting from point-like substrates indicating the small effect of the substrate on the shape of deposits.     

Measurement of axial neutral density profiles in a microwave discharge ion thruster by laser absorption spectroscopy with optical fiber probes

In order to reveal the physical processes taking place within the "μ10" microwave discharge ion thruster, internal plasma diagnosis is indispensable. However, the ability of metallic probes to access microwave plasmas biased at a high voltage is limited from the standpoints of the disturbance created in the electric field and electrical isolation. In this study, the axial density profiles of excited neutral xenon were successfully measured under ion beam acceleration by using a novel laser absorption spectroscopy system. The target of the measurement was metastable Xe I 5p(5)((2)P(0) (3/2))6s[3/2](0) (2) which absorbed a wavelength of 823.16 nm. Signals from laser absorption spectroscopy that swept a single-mode optical fiber probe along the line of sight were differentiated and converted into axial number densities of the metastable neutral particles in the plasma source. These measurements revealed a 10(18) m(-3) order of metastable neutral particles situated in the waveguide, which caused two different modes during the operation of the μ10 thruster. This paper reports a novel spectroscopic measurement system with axial resolution for microwave plasma sources utilizing optical fiber probes.     

Electrodeposition of amorphous gold alloy films

The process for electroplating amorphous gold-nickel-tungsten alloy that we developed previously based on the addition of a gold salt to a known amorphous Ni-W electroplating solution was investigated further using the X-ray diffraction (XRD) method for the purpose of quickly surveying the effects of various experimental variables on the microstructure of the alloy. In this system the gold concentration in the plating bath was found to be critical; i.e., when it is either very low or very high, the deposit becomes crystalline to XRD. The deposit composition varies linearly with the mole ratio of Au to Ni in solution, and the alloy deposit is amorphous to XRD when the atomic ratio of Au/Ni in the deposit is between 0.5 and 1.5. At suitable concentrations of the metal ions, the deposit contains essentially no tungsten. By extending the work on the Au-Ni-W system, an amorphous Au-Co alloy plating process was also developed.     

Decolorization of beads-milled TiO2 nanoparticles suspension in an organic solvent

In this paper, a new method is proposed for the decolorization of a yellow-hued suspension of rutile TiO₂ nanoparticles in an organic solvent (diethylene glycol dimethylether). The presence of color has always been undesirable in a suspension of nanoparticles filler used for industrial needs, particularly for optical applications.A colorless suspension was achieved by irradiating well-dispersed TiO₂ nanoparticles in an organic solvent with UV-light (λ = 254 nm) for 5 h. TiO₂ nanoparticles of 1 and 5 wt.% were dispersed using a beads mill method. Trimethoxytrifluor(propyl) silane was used as a dispersant to achieve stability. The effect of the UV-light irradiation on the TiO₂ nanosuspension was investigated by means of a Fourier transform nuclear magnetic resonance analyzer (FT-NMR). The dispersant was partially desorbed due to the interaction of UV light and the TiO₂/dispersant complex. Thus, an enhanced transparency and the absence of color were obtained for well-dispersed TiO₂ nanoparticles in an organic solvent.     

Effect of High-Pressure Torsion Processing and Annealing on Hydrogen Embrittlement of Type 304 Metastable Austenitic Stainless Steel

The effect of high-pressure torsion (HPT) and annealing on hydrogen embrittlement (HE) of a type 304 stainless steel was studied by metallographic characterization and tensile test after hydrogen gas charging. A volume fraction of ~78 pct of the austenite transformed to α′ martensite by the HPT processing at an equivalent strain of ~30. Annealing the HPT-processed specimen at a temperature of 873 K (600 °C) for 0.5 hours decreased the α′ martensite to ~31 pct with the average grain size reduced to ~0.43 μm through the reverse austenitic transformation. Hydrogen charge into the HPT-processed and the HPT+annealed specimens in the hydrogen content of ~10 to 20 ppm led to no severe HE but appeared in the solution-treated specimen. Especially the 873 K (600 °C) annealed specimen had the ~1.4 GPa tensile strength and the ~50 pct reduction of area (RA) despite the hydrogenation.     

Breeding of a high tyrosol‐producing sake yeast by isolation of an ethanol‐resistant mutant from a trp3 mutant

A novel breeding strategy for a high tyrosol‐producing sake yeast was developed by isolating an ethanol‐resistant mutant from a tryptophan auxotrophic mutant of a sake brewery yeast. Since tyrosol has antioxidant, cardioprotective and taste‐sharpening effects, increasing the tyrosol level of alcohol beverages could be beneficial in alcohol production. Since the transporters of aromatic amino acids are degraded by several stresses and mutants defective in the synthesis of aromatic amino acids are sensitive to ethanol, it was hypothesized that the degradation of these transporters should be inhibited in ethanol resistant mutants isolated from the auxotrophic mutants of aromatic amino acids, and that the uptake of aromatic amino acids would be increased in the mutants. Consistent with this hypothesis, sake was brewed with the ethanol‐resistant mutant of a tryptophan auxotrophic mutant and the sake was found to contain a lesser content of tyrosine and a higher content of tyrosol relative to the sake brewed with the parental strains. The taste of the sake brewed with the mutant strain could be discriminated from the sake brewed with the parental strains, probably because of the altered concentrations of tyrosol and certain amino acids and organic acids. The results suggest that combining the isolation of an ethanol‐resistant mutant and an auxotrophic mutant is an effective method to breed a brewing strain with a modified metabolism of these substances. Copyright © 2012 The Institute of Brewing & Distilling