汽车涂装车间产品一次交检合格率提升方法

阐述了强化过程质量控制,提升产品一次交检合格率对汽车生产企业的重要性.以某车间为例,就人、机、料、法、环五个方面影响汽车涂装生产最终产品质量的因素进行了分析,列举了各项问题的解决措施.     

纯铝等径角挤技术（I）——显微组织演化

研究了纯铝在 3种 (A、B和C)不同等径角挤工艺中的显微组织演化。结果表明 :纯铝经过等径角挤压变形后 ,其显微组织特征与加工路线有很大的关系。提出了立方元素扭转模型 ,分析了 3种不同加工路线的剪切面和剪切方向 ,较好地解释了采用 3种不同路线挤压后材料显微组织的演化规律。在路线C(各道次挤压间试样旋转 180°)中 ,每次挤压样品总是在相同的剪切面上发生剪切 ,每相邻道次之间的剪切方向相反 ,前一次变形产生的剪切应变被随后紧接着的下一次挤压所抵消 ,这导致了多余的剪切应变 ;在路线A(各道次挤压间试样不旋转 )中 ,有两个相交成 6 0°的剪切面 ,剪切交替地在两个剪切面上进行 ;在路线B(各道次挤压间试样旋转 90°)中 ,存在 4个不同的剪切面和剪切方向 ,挤压交替地在 4个剪切面上进行 ,X ,Y和Z平面上的晶粒都发生了剪切 ,这有利于等轴晶结构的形成     

Effects of can parameters on canned—forging process of TiAl base alloy（Ⅱ）——Mechanical behavior

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＡｌａｌｌｏｙｈａｓｌｏｎｇｂｅｅｎｃｏｎｓｉｄｅｒｅｄａｓａｐｒｏｍｉｓ ｉｎｇｍａｔｅｒｉａｌｆｏｒｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎ ,ｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｈｉｇｈｔｅｍｐｅｒａｔｕｒｅ ｐ     

冷却强度及变形程度对挤压AZ31镁合金组织性能的影响

选择AZ31镁合金为原材料,在400℃下挤压散热片型材,就冷却强度及变形程度对制品的性能(抗拉强度和导电率)及组织结构的影响进行研究。结果显示:挤压温度为400℃,制品经水冷却,变形程度大的型材具有更高的抗拉强度和导电率。     

铝合金牺牲阳极电流效率损耗的微观分析

探针（EPMA）和能谱分析技术(EDAX)，考察了铝合金牺牲阳极的显微结构和腐蚀后的边缘形貌，讨论了电流效率和显微组织之间的关系.结果表明：晶界腐蚀引起的晶粒脱落是铝合金牺牲阳极电流效率损耗的重要原因.      

FS-1化学镀Ni-P镀层的性能研究

采用XRD与SEM分析技术、电化学阳极极化曲线测试和 摩擦磨损试验等，系统地研究了FS-1化学镀Ni-P镀层的结构和性能.结果表明：该镀层具有 优良的耐蚀和耐磨性能，热处理虽可以显著地提高镀层的耐磨性能，但使其耐蚀性能有所降 低.     

非晶态Pd—Cu—Si合金的晶化动力学研究

本文应用DSC研究了非晶态Pd-Cu-Si合金的晶化过程动力学.根据Kissinger峰移法和Arrhenius方程分别计算了晶化激活能,发现等温晶化动力学在0.15相似文献   

Kinetics of synthesis of Li4Ti5O12 through solid-solid reaction

1. Introduction The solid-solid reaction used in synthesizing various kinds of electrochemical materials has many advantages, such as simple process, without using solvent, saving energy, friendly to the environment and easy to obtain good quality materials like nano-size materials. Recently, the manufacturing of electrochemistry materials has been paid more atten- tion due to its increasing needs. Therefore it is a natural interest to study the synthesis of electro- chemical materials by usin…     

Effect of sintering process on microstructure and magnetic properties of high frequency power ferrite

An oxide ceramic process was adopted to prepare high frequency manganese-zinc (MnZn) power ferrite. In combination with the microstructure analysis of material, the influences of sintering process on initial permeability (μi) and high frequency loss in unit volume (Pcv) of MnZn power ferrite were investigated. The results show that in order to obtain fine microstructure and high frequency properties, the preferable sintering temperature and atmosphere are 1230 ℃ and oxygen partial pressure ( PO2) of 4%, respectively.     

Microstructure and magnetic performance of Ni-substituted high density MnZn ferrite

The effects of NiO on microstructure and magnetic properties of Mn-Zn ferrite with a nominal composition of Zn0.32Mn0.60-xNixFe2.08O4 were investigated. The calcined powder of Mn-Zn ferrite was characterized by X-ray diffraction (XRD), the fracture surface of Mn-Zn ferrite was checked by scanning electronic microscope (SEM), and then the magnetic properties were measured. As a result, the substitution of Ni can cause the crystallattice constant of MnZn ferrite to decline, and the grain size to decrease, therefore improve the magnetic performance of MnZn ferrite whose density exceeds 5.0 g·cm-3.