High-cycle fatigue characteristics of quasi-isotropic CFRP laminates over 10 cycles (Initiation and propagation of delamination considering interaction with transverse cracks)

High-cycle fatigue features of over 10⁸ cycles, particularly the initiation and propagation of edge delamination considering the effects of transverse cracks, were investigated using quasi-isotropic carbon-fiber-reinforced plastic (CFRP) laminates with a stacking sequence of [45/0/−45/90]_s in this study. In the relationship between a transverse crack density and initiation and growth of edge delamination, it was found that fatigue damage growth behavior varied depending on applied stress. It was observed that edge delamination initiated and grew at parts where transverse cracks were dense at ordinary applied stress, whereas it was observed that edge delamination grew before or simultaneously with transverse crack propagation at a low applied stress and high-cycle loading. In addition, the critical transverse crack density where delamination begins growing was calculated to evaluate the interaction between transverse crack and edge delamination growth.     

Local changes in blood flow within the preovulatory follicle wall and early corpus luteum in cows

Haemodynamic changes are involved in the cyclic remodelling of ovarian tissue that occurs during final follicular growth, ovulation and new corpus luteum development. The aim of this study was to characterize the real-time changes in the blood flow within the follicle wall associated with the LH surge, ovulation and corpus luteum development in cows. Normally cyclic cows with a spontaneous ovulation (n = 5) or a GnRH-induced ovulation (n = 5) were examined by transrectal colour and pulsed Doppler ultrasonography to determine the area and the time-averaged maximum velocity (TAMXV) of the blood flow within the preovulatory follicle wall and the early corpus luteum. Ultrasonographic examinations began 48 h after a luteolytic injection of PGF(2alpha) analogue was given at the mid-luteal phase of the oestrous cycle. Cows with spontaneous ovulation were scanned at 6 h intervals until ovulation occurred. Cows with GnRH-induced ovulation were scanned just before GnRH injection (0 h), thereafter at 0.5, 1, 2, 6, 12, 24 h and at 24 h intervals up to day 5. Blood samples were collected at the same time points for oestradiol, LH and progesterone determinations. Cows with both spontaneous and GnRH-induced ovulation showed a clear increase in the plasma concentration of LH (LH surge) followed by ovulation 26-34 h later. In the colour Doppler image of the preovulatory follicle, the blood flow before the LH surge was detectable only in a small area in the base of the follicle. An acute increase in the blood flow velocity (TAMXV) was detected at 0.5 h after GnRH injection, synchronously with the initiation of the LH surge. At 12 h after the LH surge, the plasma concentrations of oestradiol decreased to basal concentrations. The TAMXV remained unchanged after the initial increase until ovulation, but decreased on day 2 (12-24 h after ovulation). In the early corpus luteum, the blood flow (area and TAMXV) gradually increased in parallel with the increase in corpus luteum volume and plasma progesterone concentration from day 2 to day 5, indicating active angiogenesis and normal luteal development. Collectively, the complex structural, secretory and functional changes that take place in the ovary before ovulation are closely associated with a local increase in the blood flow within the preovulatory follicle wall. The result of the present study provides the first visual information on vascular and blood flow changes associated with ovulation and early corpus luteum development in cows. This information may be essential for future studies involving pharmacological control of blood flow and alteration of ovarian function.     

Application of a novel technique for band sawing using a tip-inserted saw regarding surface profiles

One way of achieving a successful forest management leading to biodiversity conservation is to ensure that wood is processed in an efficient manner. The authors succeeded in developing a new technology for bandsawing using a tip-inserted saw. The material used for the tipped edge was High Speed Steel (HSS) of designation SHK 51 according to the Japan Industrial Standard (JIS). The efficiency of the tip-inserted saw was investigated considering its effectiveness in controlling tooth marks and washboarding patterns that sometimes occur during bandsawing. The surface profile of the workpiece generated after sawing with 700 mm and 1100 mm diameter bandmills of the laboratory and industrial type respectively were determined using a CCD laser displacement sensor of scanning length 250 mm and scanning speed of 3 mm/sec at a sampling rate of 50 Hz. Under a setup wheel rotation speed of 200 rpm and feed speed of 1 m/min, washboardings were induced during sawing with the tip-inserted saw of uniform pitch. Thereafter, a tip-inserted saw of random pitch was constructed without removing the saw from the pulley and cutting tests were performed under the same cutting conditions when washboardings were induced during sawing with the uniform pitch tipped-inserted saw. It was observed that the washboarding pattern disappeared completely. Thus the tip-inserted saw of random pitch was very effective in controlling the washboarding pattern. Comparisons of the surface profiles of the workpiece generated by sawing with uniform pitch tip-inserted and stellite-tipped saws under both laboratory and industrial conditions indicate that regardless of the type of bandmill used, the surface profile measured with the laser displacement sensor was smoother for tip-inserted saws than stellite-tipped saws.     

Shear properties of metal-free wooden load-bearing walls using plywood jointed with a combination of adhesive tape and wood dowels

In this study, the potential of wood-only (metal-free) load-bearing walls was proposed and tested based on the idea of using the same type of material throughout wherever possible while improving basic properties such as strength, sound insulation, and heat insulation. Specifically, a technique was tested of combining pressure sensitive adhesive tape and wood dowels in place of nails for load-bearing structures with panel reinforcement represented by wood-frame construction. For this paper, its strength was evaluated by conducting in-plane shear tests, which revealed that the initial rigidity and maximum load of the proposed test specimens were greater than that of specimens using nails for jointing. However, the shear load factor, which is calculated based on some strength parameters and which forms the foundation of housing strength design, was slightly lower than that of the nail-jointed specimen. This was because there was a large decline in post-collapse resistance and a lower calculated absorbed energy caused by brittleness. The early detachment of panels was also revealed as a problem in the tests.     

Novel episomal vectors and a highly efficient transformation procedure for the fission yeast Schizosaccharomyces japonicus

Schizosaccharomyces japonicus is a fission yeast for which new genetic tools have recently been developed. Here, we report novel plasmid vectors with high transformation efficiency and an electroporation method for Sz. japonicus. We isolated 44 replicating segments from 12 166 transformants of Sz. japonicus genomic fragments and found a chromosomal fragment, RS1, as a new replicating sequence that conferred high transformation activity to Sz. japonicus cells. This sequence was cloned into a pUC19 vector with ura4⁺ of Sz. pombe (pSJU11) or the kan gene on the kanMX6 module (pSJK11) as selection markers. These plasmids transformed Sz. japonicus cells in the early‐log phase by electroporation at a frequency of 123 cfu/µg for pSJK11 and 301 cfu/µg for pSJU11, which were higher than previously reported autonomously replicating sequences. Although a portion of plasmids remained in host cells by integration into the chromosome via RS1 segment, the plasmids could be recovered from transformants. The plasmid copy number was estimated to be 1.88 copies per cell by Southern blot analysis using a Sz. pombe ura4⁺ probe. The plasmid containing ade6⁺ suppressed the auxotrophic growth of the ade6‐domE mutant, indicating that the plasmid would be useful for suppressor screening and complementation assays in Sz. japonicus. Furthermore, pSJU11 transformed Sz. pombe cells with the same frequency as the pREP2 plasmid. This study is a report to demonstrate practical use of episomal plasmid vectors for genetic research in Sz. japonicus. RS1 has been submitted to the DDBJ/EMBL/GenBank database (Accession No. AB547343). Copyright © 2010 John Wiley & Sons, Ltd.     

Zur Strukturaufklärung der Bromierungsprodukte von N-Aryl-2,4-dimethyl-buta-1,3-dien-sultamen-1,4

Structure Elucidation of Bromination Products of N-Aryl-2, 4-dimethyl-buta-1,3-diene-sultames-1, 4 The structure of bromination products of N-aryl-2, 4-dimethyl-buta-1, 3-diene-sultames-1, 4 1a–d , f is determined by 13-C-n.m.r. spectroscopy. As mono bromination product of N-phenylsultam 1a the 4-bromomethyl derivative 2a was isolated. Dibromination of sultames 1 yields 1-brom-4-brommethyl-sultames 3 and by tribromination 1,3-dibrom-4-brommethyl-sultames 4 are obtained.     

Transmission electron microscope observation of organic–inorganic hybrid thin active layers of light-emitting diodes

Low-resistivity indium tin oxide [ITO] film was successfully deposited on oxygen plasma-treated polyethylene terephthalate [PET] surfaces at room temperature. X-ray diffraction [XRD] measurements demonstrated that the film deposited on the PET surface that had not been treated with oxygen plasma had an amorphous structure. In contrast, after the low-power oxygen plasma treatment of the PET surface, the ITO film deposited on the PET surface had a poly-crystalline structure due to interactions between electric dipoles on the PET surface and electric dipoles in the ITO film. The minimum resistivity of the poly-crystalline ITO was about 3.6 times lower than that of the amorphous ITO film. In addition, we found that the resistivity of ITO film is proportional to the intensity of the (400) line in the film's XRD spectra.     

Novel synthesis of microcrystalline titanium(IV) oxide having high thermal stability and ultra-high photocatalytic activity: thermal decomposition of titanium(IV) alkoxide in organic solvents

Thermal decomposition of titanium(IV) tetra-tert-butoxide (TTB) in inert organic solvents at 573 K yielded microcrystalline anatase (titanium(IV) oxide, TiO₂) powders with a crystallite size of ca. 9 nm and a surface area of <100 m² g^-1. Primary and secondary alkoxides of titanium(IV), however, were not decomposed under similar conditions, indicating that the thermal stability of C-O bonds in the alkoxides was a decisive factor for their decomposition. The TiO₂ prepared from TTB by this manner was thermally stable upon calcination in air and retained high surface area of ca. 100 m² g^-1 even after calcination at 823 K. The as-prepared TiO₂ powders, without calcination, exhibited much higher rate of carbon dioxide formation than any other active photocatalysts such as Degussa P-25 and Ishihara ST-01 in the photocatalytic mineralization of acetic acid in aerated aqueous solutions. The higher activity of the present TiO₂ photocatalysts is attributed to both high crystallinity and large surface of the present product. The calcination of the as-prepared TiO₂ in air reduced the photocatalytic activity, but it was still higher than the other commercially available TiO₂'s. This revised version was published online in July 2006 with corrections to the Cover Date.     

High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.