Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Structural system identification: from reality to models

The paper is an expository contribution on the subject of structural system identification, measured signal processing and their applications to model-based structural health detection. The materials covered in this paper are by and large extracted from the three theses of the first three authors. The paper focuses on the state-space oriented system identification theory as specialized to structural dynamics governing equations of motion, a judicious use of wavelet transformation techniques for extracting impulse response functions, various input-output combinations for multi-input and multi-output problems, robust ways of identifying both proportional and non-proportional damping parameters, and the use of localized identification theory for damage detection from measured response data. The authors then offer several outstanding challenges in structural system identification theory and their applications.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

540kN力基准机砝码摆动的研究

日本国家计量研究院(National Research Laboratory of Metrology)540kN静重式力基准机中的振荡分量主要是由于砝码的摆动引起的。本文对砝码的动态特性做了详细的分析，给出了其摆动的轨迹图，并对由于砝码摆动引起的相对不确定度进行了评估。提出了一类采用传感器并联的叠加系统(以下称叠加系统)输出的力值信号来评估砝码动态特性的信号处理方法。它对研究静重式测力机砝码摆动提供了有效的分析方法。     

Epitaxial growth of GaN on (0001) Al<Subscript>2</Subscript>O<Subscript>3</Subscript> via solution-cast seed layer formation process using Ga(mDTC)<Subscript>3</Subscript>

This paper reports an alternative method for the growth of GaN epitaxial layer on (0001) Al₂O₃ substrate by hot-wall vapor phase epitaxy technique. Tris (N,N-dimethyldithiocarbamato)-gallium (III), Ga(mDTC)₃ was introduced as a precursor material for the seed layer formation in the growth of GaN. Optimal growth conditions with seed layers formed by the Ga(mDTC)₃ concentration of 0.047 mol/L were identified: Growth temperature was found to be 850 °C, and optimal distance between the reactant outlet and substrate was determined to be 12.5 cm. Characterization results showed that this growth method produce high-crystallinity GaN epitaxial layers at a relatively lower growth temperature compared to the existing growth techniques and simplify the growth process.     

Nucleoside-diphosphate kinase-mediated signal transduction via histidyl-aspartyl phosphorelay systems in Escherichia coli

Nucleoside-diphosphate kinase (NDP kinase), a key enzyme in nucleotide metabolism, is also known to be involved in growth and developmental control and tumor metastasis suppression. Interestingly, we find that coexpression of NDP kinase with Taz1, a Tar/EnvZ chimera, in the absence of its native signal, can activate a porin gene ompC-lacZ expression in Escherichia coli. Further studies show that NDP kinase can act as a protein kinase to phosphorylate histidine protein kinases such as EnvZ and CheA which are members of the His-Asp phosphorelay signal transduction systems in E. coli. Instead of ATP, the exclusive phosphodonor for histidine kinases, GTP can be utilized in vitro in the presence of NDP kinase to phosphorylate EnvZ and CheA, which then transfer the phosphoryl group to OmpR and CheY, the respective response regulators. The direct involvement of GTP for the phosphorylation of EnvZ through NDP kinase was further demonstrated by the use of a mutant EnvZ, which lost ability to be autophosphorylated with ATP. Phospho-OmpR thus formed can bind specifically to an ompF promoter sequence. These results suggest that NDP kinase may play a physiological role in signal transduction.     

Nicalon-fibre-reinforced silicon-carbide composites via polymer solution infiltration and chemical vapour infiltration

A new, faster process was developed for the fabrication of Nicalon-fibre-reinforced SiC composites by combining polymer solution infiltration (PSI) and chemical vapour infiltration (CVI). The process led to the near-net-shape fabrication of fibre-reinforced ceramic-matrix composites and reduced infiltration time. Typical flexural strength and fracture toughness of these composites were 296 MPa and 10.9 MPa m^1/2 at room temperature (RT) and 252 MPa and 9.6 MPa m^1/2 at 1000 °C, respectively. The composites exhibited load-carrying capability after crack initiation.     

Identification of urinary dipeptidase as the released form of renal dipeptidase

Beckwith-Wiedemann syndrome (BWS) comprises of a number of childhood abnormalities, often associated with one or more tumors. Thirty-eight patients were investigated to determine clinical and/or biological signs associated with a tumor presence. Our patients exhibited a higher incidence of tumor development (21%) than that previously reported, underlying the care with which such patients should be followed, when particular clinical features are observed: visceromegaly affecting three organs (liver, kidney, spleen), and also family history with sign of BWS such as macroglossia, omphalocele, hemihypertrophy, embryonic tumor), high body weight at birth (> or = +2 standard deviations and diastasis recti.