Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

Formation of the complex oxide NaNdTiO<Subscript>4</Subscript>

The processes of phase formation in the Na₂CO₃-TiO₂ and Na₂CO₃-TiO₂-Nd₂O₃ systems are investigated in the temperature range 600–900°C. The high-temperature solid-phase reactions underlying the process of formation of complex oxide NaNdTiO4 are studied. It is established that the synthesis of the NaNdTiO₄ compound occurs through the reaction of the intermediate product Na₈Ti₅O₁₄ with neodymium oxide in the temperature range 720–780°C. The optimum method is proposed for synthesizing NaNdTiO₄, which makes it possible to reduce the temperature of the synthesis, to avoid the formation of impurities, and to obtain the product in a finely dispersed state.     

Software for computing dusty air flows in ventilation systems

Programs are presented for calculating dusty air flow in ventilation systems, which have been derived from the method of singular integral equations. They allow one to construct flow lines and determine the velocity pattern for the air in a closed rectangular region with outlet, flow, and extraction holes; a study is made on the dust particle behavior in the aerodynamic field in which there may be a rotating cylinder or pumping cylinder; determinations are made of the concentration and grain-size composition of the dust in the extraction hole; one can construct flow lines and single-particle paths in multicoupled regions of potential flows containing any number of rotating cylinders and cylinder pumps. Translated from Novye Ogneupory, No. 5, pp. 53–58, May, 2008.     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

High-power 1.7–1.8 μm single-mode laser diodes

Separate confinement InGaAsP/InP laser heterostructures were grown by metalorganic-hydride vapor-phase epitaxy. High-power single-mode laser diodes of mesastripe design based on these heterostructures operate in a wavelength interval of 1.7–1.8 μm with a maximum continuous room temperature output power of 150 mW. The single-mode lasing regime is maintained up to an output power level of 100 mW.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

A rubber-modified thermoplastic where the morphology produced by phase-separation induced by polymerization disappears at high conversions

An unexpected experimental finding is reported where the primary morphology developed during polymerization-induced phase separation in a rubber-modified thermoplastic practically disappears at high conversions. This process was evidenced by light scattering (LS) and scanning electron microscopy (SEM) for a particular composition of solutions of polyisobutylene oligomers (PIB) in isobornylmethacrylate (IBoMA), during the free-radical polymerization of the monomer. The primary phase separation produced a dispersion of domains rich in PIB containing significant amounts of the monomer (IBoMA). Polymerization of the monomer in these domains occurred at high overall conversions producing the filling of dispersed domains with a PIBoMA-PIB blend that could not be distinguished from the matrix. Under these conditions the final material had the appearance of a homogeneous blend.