Application results of a prototype ultrasonic liquid film sensor to a 7 MPa steam–water two-phase flow experiment

A prototype ultrasonic liquid film sensor was applied to a high-temperature steam–water two-phase flow experiment. The liquid film sensor was vertically installed in a loop which was connected to HUSTLE, a multi-purpose steam source test facility. The hydraulic diameter of the measurement section was 9.4 mm. The output waveforms of the sensor were acquired with a digital oscilloscope. The fluid temperature and system pressure were kept at 288 °C and 7.2 MPa, respectively, during the experiment. The pulse-echo method was used to calculate the liquid film thickness. The cross-correlation calculation was utilized to determine the time difference between the pulse reflected at the sensor surface and the pulse reflected at the liquid film surface. The time-averaged liquid film thicknesses were less than 0.055 mm in the annular flow condition. The increase of the time-averaged thickness was small with the change of the gas momentum flux. The film thicknesses measured with the sensor were compared with the past experimental results; the former were smaller than one-fourth of the thickness estimated as the mean film thickness. The comparison results suggested that the continuous liquid sublayer thickness was measured with the liquid film sensor.     

Structural characterization of photoreduced complete and incomplete cubane-type molybdenum oxide clusters in CO and their catalytic behavior in propene metathesis reaction

SiO2-impregnated complete and incomplete cubane-type molybdenum oxide clusters such as [(RhCp*)₄Mo₄O₁₆] (I) and [(RhCp*)₂Mo₃O₉(OMe)₄] (II) were photoreduced with a UHP-Hg lamp (> 365 nm) in CO, resulting in the formation of catalytically active species for propene metathesis at 300 K. The CO-photoreduced Mo oxide clusters were characterized by EXAFS, IR, XPS and TPD technique. The results suggest that the Mo-O_4c (four-centered bridging oxygens) in I were specifically reduced with CO under the illumination to produce two sets of subcarbonyl species, e.g., those characteristic of the IR bands at 2061 and 2021 cm^–1, which were thermally inactive for the¹³CO exchange reaction but very active under illumination at 300 K, possibly assignable to Mo(CO)x (x = 2, 3), whereas those at 2092 and 2035 cm^–1 due to Rh(CO)₂, which were readily exchangeable with¹³CO at 300 K in dark. Removal of both carbonyls attached on Rh and Mo in photoreduced I and II by evacuation at 375–440 K led to the formation of oxygen-deficient Mo⁴+/Mo⁵⁺ sites, which exhibited high catalytic activities in propene metathesis at 300 K to produce an equimolar mixture of ethene and 2-butenes. The CO-photoreduced incomplete cubane Mo oxide cluster (II) exhibited higher activities and higher trans/cis ratios of 2-butenes in the reaction, compared with those on the photoreduced I.     

Combustion synthesis of LaSi3N5:Eu2+ phosphor powders

LaSi₃N₅:Eu²⁺ phosphor powders were prepared by a highly efficient combustion synthesis method. It was found that the compositions of the raw powder mixtures had great influences on the phase compositions and particle morphologies of the synthesized powders. By selecting appropriate starting compositions and combustion parameters, single phase LaSi₃N₅:Eu²⁺ phosphors could be synthesized. When excited by a UV light, the LaSi₃N₅:Eu²⁺ phosphors emitted green light. The wavelength and intensity of the emission spectra were affected by the amount of Eu²⁺ dopant. With increasing amount of Eu²⁺ dopant, concentration quenching could occur and emission spectra shifted to longer wavelengths.     

The effect of lutein supplementation on visual fatigue: A psychophysiological analysis

We used psychophysiological technology to examine the effect of an oral supplement, a combination of lutein, zeaxanthin and blackcurrant extract (LUT), on visual fatigue, within the context of a randomized, double-blind, placebo-controlled cross-over trial. The LUT supplement and placebo samples were randomly assigned to thirteen participants, who took the samples for two LUT (and vice versa) for another 2 week. Each participant completed visual proof reading tasks for 2 h during each of four testing sessions. Saccade tests were administered before and after the proof reading task, during which the participants moved their eyes back and forth between two targets positioned in the center of two checkerboards. We recorded EEG, EOG, heart rate, and facial muscle potential/performance during the saccade tests. Blood pressure was measured and subjective fatigue and stress scores were collected before and after the proof reading task. We averaged EEG starting at saccade offset in order to analyze eye fixation related potentials (EFRP). Our results suggested that the proof reading task induced visual fatigue. An analysis of EFRP and other psychophysiological data revealed significant differences between the LUT and placebo conditions. These results suggest that supplementation with LUT could help to reduce symptoms of visual fatigue.     

Decomposition and regeneration of methane in the absence and the presence of a hydrogen-absorbing alloy CaNi5

Suitable catalysts for the decomposition of methane into carbon and hydrogen and for the regeneration of methane by hydrogenation of the carbon have been looked for in a series of transition metals and precious metals supported on various carriers. The most active catalyst for both reactions was Ni/SiO₂. The carbon formed on this catalyst was thermodynamically less stable than graphite. The different rate equations for the decomposition of methane obtained for the fresh and carbon deposited Ni/SiO₂ suggest that the rate-determining steps are different for the two catalysts. The highest number of carbon atoms deposited per one Ni atom was 31 at 773 K. However, the number of methane molecules recovered easily at 773 K was limited to 1.5 per Ni atom.

A physical mixture of Ni/SiO₂ and CaNi₅, a hydrogen-absorbing alloy, enhanced the decomposition rate of methane, enabling the complete conversion of methane at 773 K beyond the thermodynamic limitation. The presence of CaNi₅ at 273 K separated from the catalyst in a reaction system further enhanced the decomposition of methane due to an increased hydrogen-absorbing capacity of the CaNi₅ at low temperatures. The carbon deposited on Ni/SiO₂ in this case was reactive to be hydrogenated back to methane at 773 K, giving an average 7.5 CH₄ molecules per one Ni atom.     

Microstructural Design of Silicon Nitride with Improved Fracture Toughness: II, Effects of Yttria and Alumina Additives

Significant improvements in the fracture resistance of self-reinforced silicon nitride ceramics have been obtained by tailoring the chemistry of the intergranular amorphous phase. First, the overall microstructure of the material was controlled by incorporation of a fixed amount of elongated ß-Si₃N₄ seeds into the starting powder to regulate the size and fraction of the large reinforcing grains. With controlled microstructures, the interfacial debond strength between the reinforcement and the intergranular glass was optimized by varying the yttria-to-alumina ratio in the sintering additives. It was found that the steady-state fracture toughness value of these silicon nitrides increased with the Y:Al ratio of the oxide additives. The increased toughness was accompanied by a steeply rising R -curve and extensive interfacial debonding between the elongated ß-Si₃N₄ grains and the intergranular glassy phase. Microstructural analyses indicate that the different fracture behavior is related to the Al (and O) content in the ß´-SiAlON growth layer formed on the elongated ß-Si₃N₄ grains during densification. The results imply that the interfacial bond strength is a function of the extent of Al and Si bonding with N and O in the adjoining phases with an abrupt structural/chemical interface achieved by reducing the Al concentration in both the intergranular phase and the ß´-SiAlON growth layer. Analytical modeling revealed that the residual thermal expansion mismatch stress is not a dominant influence on the interfacial fracture behavior when a distinct ß´-SiAlON growth layer forms. It is concluded that the fracture resistance of self-reinforced silicon nitrides can be improved by optimizing the sintering additives employed.     

Advanced grid connected PV system with functions to suppress disturbance by PV output variation and customer load change

The PV array has unstable output patterns dependent on weather conditions. Therefore, assuming high-density grid connection in the future, these unstable output patterns can be one of the main reasons to cause power disturbances such as the voltage variation, the frequency variation and the harmonic voltage generation into utility. And also it should be considered that a sudden customer load change is one of those reasons. Therefore, this study suggested a PV system with suppression functions against such disturbances in the side of amicable relationship with utility and verified the validity of the proposed system by EMTP and ACSL-based analysis.     

Contact force detection on a minute aperture mounted optical contact slider using an acoustic emission sensor

Advances in the digital network society require both higher density and higher transfer rates in all sorts of storage systems. Especially in optical recording, the trend toward higher density and larger capacity requires novel surface-recording technologies that can drastically diminish head-to-medium spacing, resulting in an improvement in spatial resolution and, finally, a higher recording density. To this end, we have already proposed a novel contact optical head slider that is able to almost cancel the suspension load by generating hydrodynamic pressure, thus realizing a lower net contact force. Evaluating the dynamic contact force is requisite in realizing its stable sliding operation and higher signal readout performance. In this study, a continuous acoustic emission (AE) signal was utilized to detect the dynamic contact force. AE signal modulation was compared with the applied out-of-plane acceleration on a medium generated by a spindle combined piezo-electric actuator. It was clarified that the detected AE modulation amplitude was approximately proportional to the applied acceleration, and that utilizing AE modulation will be a useful method for evaluating dynamic contact force.     

Preparation of Aluminum Nitride–Silicon Carbide Nanocomposite Powder by the Nitridation of Aluminum Silicon Carbide

Aluminum nitride (AlN)–silicon carbide (SiC) nanocomposite powders were prepared by the nitridation of aluminum-silicon carbide (Al₄SiC₄) with the specific surface area of 15.5 m²·g⁻¹. The powders nitrided at and above 1400°C for 3 h contained the 2H-phases which consisted of AlN-rich and SiC-rich phases. The formation of homogeneous solid solution proceeded with increasing nitridation temperature from 1400° up to 1500°C. The specific surface area of the AlN–SiC powder nitrided at 1500°C for 3 h was 19.5 m²·g⁻¹, whereas the primary particle size (assuming spherical particles) was estimated to be ∼100 nm.     

Enantioselective addition Of diketene to aldehydes promoted by chiral schiff base—titanium alkoxide complex. Application to asymmetric synthesis of potential inhibitors of HMG coenzyme reductase

Highly enantioselective addition of diketene to aldehydes was achieved by using novel Schiff base—titanium alkoxide complexes. Up to 92% ee of 5-hydroxy-3-oxoesters was obtained. This procedure provides an efficient method for the asymmetric synthesis of potential inhibitors of HMG coenzyme reductase.