螺杆压缩机性能模拟的误差分析及稳定性判据

在螺杆压缩机作动室的压力脉动模拟分析中,针对采用的数值计算方法———Rouge＿Kutta法可能由于计算舍入误差累积而造成计算发散,提出导入Simpson误差评价公式,建立了评价作动室排气过程中的计算误差的数学模型.同时针对排气行程中,由于作动室压力和排气室压力非常接近,造成计算误差增大的倾向,通过数学推证,得到对处于排气行程的作动室的压力脉动进行数值计算的稳定性判据,对模拟计算结果的收敛性提供保障.     

Czochralski growth of Yb doped oxyapatite for high power laser application

Ca₈(La,Yb)₂(PO₄)₆O₂ (Yb:CLPA) single crystals with the apatite-type structure could be grown from the melt using the Czochralski method. Grown crystal was 18 mm in diameter and 110 mm in length. It is transparent with slightly blue color. Neither visible inclusion nor crack was observed. Thermal conductivity of Yb:CLPA was calculated from the values of thermal diffusivity, heat capacity measurement and density. Luminescent characterization was carried out from the results of emission, absorption and Raman spectrum.     

Leak-tightness characteristics concerning the containment structures of the HTTR

The containment structures of the HTTR consist of the reactor containment vessel, the service area, and the emergency air purification system, which minimise the release of fission products in postulated accidents, which lead to fission product release from the reactor facilities. The reactor containment vessel is designed to withstand the temperature and pressure transients and to be leak-tight in the case of a rupture of the primary concentric hot-gas duct, etc. The pressure inside the service area is maintained at a negative pressure by the emergency air purification system. The emergency air purification system will also remove airborne radioactivity and will maintain a correct pressure in the service area.The leak-tightness characteristics of the containment structures are described in this paper. The measured leakage rates of the reactor containment vessel were enough less than the specified leakage limit of 0.1%/d confirmed during the commissioning tests and annual inspections. The service area was kept in a way that the design pressure becomes well below its allowable limitation by the emergency air purification system, which filters efficiency of particle removal and iodine removal well over the limited values.The obtained data demonstrate that the reactor containment structures were fabricated to minimise the release of fission products in the postulated accidents with fission product release from the reactor facilities.     

Nonmagnetic indenter-type high-pressure cell for magnetic measurements

An indenter-type high-pressure cell has been developed for electric and magnetic measurements in low-temperature and high-magnetic-field environments. The maximum pressure achieved at low temperatures is more than 4.5 GPa, which is higher than that of a conventional piston-cylinder cell. The typical sample space at maximum pressure is 1.6 mm in diameter and approximately 0.7 mm in depth, and magnetic measurements such as ac-susceptibility and nuclear magnetic resonance can be performed using a miniature coil. All the components of the indenter cell are made of nonmagnetic materials that have enough thermal conductivity for low-temperature experiments using a 3He/4He dilution refrigerator. Another indenter-type cell designed for a commercial superconducting quantum interference device magnetometer is also reported.     

Martensitic stabilization and defects induced by deformation in TiNi shape memory alloys

Martensitic stabilization caused by deformation in a TiNi shape memory alloy was studied.Special attention was paid to the deformed microstructures to identify the cause of martensitic stabilization.Martensitic stabilization was demonstrated by differential scanning calorimetry for the tensioned TiNi shape memory alloy.Transmission electron microscopy revealed that antiphase boundaries were formed because of the fourfold dissociation of[110]B19'super lattice dislocations and were preserved after reverse transformation due to the lattice correspondence.Martensitic stabilization was attributed to dislocations induced by deformation,which reduced the ordering degree of the microstructure,spoiled the reverse path from martensite to parent phase compared with thermoelastic transformation,and imposed resistance on phase transformation through the stress field.     

Investigations on welding residual stresses in penetration nozzles by means of 3D thermal elastic plastic FEM and experiment

Recent discoveries of stress corrosion cracking (SCC) in weldments including penetration nozzles at pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It is well known that welding residual stress is an important factor resulting in SCC in weldments. In the present work, both experimental method and numerical simulation technology are used to investigate the characteristics of welding residual stress distribution in penetration nozzles welded by multi-pass J-groove joint. An experimental mock-up is fabricated to measure welding residual stress at first. In the experiment, each weld pass is performed using a semi-circle balanced welding procedure. Then, a corresponding finite element models with considering moving heat source, deposition sequence, inter-pass temperature, temperature-dependent thermal and mechanical properties, strain hardening and annealing effect is developed to simulate welding temperature and residual stress fields. The simulation results predicted by the 3D model are generally in good agreement with the measurements. Meanwhile, to clarify the influence of deposition sequence on the welding residual stress, the welding residual stress field in the same geometrical model induced by a continuous welding procedure is also calculated. Finally, the influence of a joint oblique angle on welding residual stress is investigated numerically. The numerical results suggest that both deposition sequence and oblique angles have effect on welding residual stress distribution.     

Development of correlation-based clustering method and its application to software sensing

The individuality of production devices should be taken into account when soft-sensors are designed for parallelized devices. Since it is expressed as differences of the correlation among measured variables, it is useful to cluster samples on the basis of the correlation among variables for adopting a multi-model approach. In addition, changes in process characteristics can be coped with in the same way. In the present work, a new clustering method, referred to as NC-spectral clustering, is proposed by integrating the nearest correlation (NC) method and spectral clustering. Spectral clustering is a graph partitioning method that can be used for sample classification when an affinity matrix of a weighted graph is given. The NC method can detect samples that are similar to the query from the viewpoint of the correlation without a teacher signal. In the proposed method, the NC method is used for constructing the weighted graph that expresses the correlation-based similarities between samples and the constructed graph is partitioned by using spectral clustering. In addition, a new soft-sensor design method is proposed on the basis of the proposed NC-spectral clustering. The usefulness of the proposed methods is demonstrated through a numerical example and a case study of parallelized batch processes. The performance of the proposed correlation-based method is better than that of the conventional distance-based methods.     

Psychological Stress Exacerbates Inflammation of the Ileum via the Corticotropin-Releasing Hormone-Mast Cell Axis in a Mouse Model of Eosinophilic Enteritis

The effects of psychological stress on eosinophilic gastrointestinal disorders have not been elucidated. This study investigated the effects of psychological stress in a mouse model of eosinophilic enteritis (EoN). BALB/c mice were treated with ovalbumin (OVA) to create an EoN model and subjected to either water avoidance stress (WAS) or sham stress (SS). Microscopic inflammation, eosinophil and mast cell counts, mRNA expression, and protein levels of type 2 helper T cell (Th2) cytokines in the ileum were compared between groups. We evaluated ex vivo intestinal permeability using an Ussing chamber. A corticotropin-releasing hormone type 1 receptor (CRH-R1) antagonist was administered before WAS, and its effects were analyzed. WAS significantly increased diarrhea occurrence and, eosinophil and mast cell counts, and decreased the villus/crypt ratio compared to those in the SS group. The mRNA expression of CRH, interleukin IL-4, IL-5, IL-13, eotaxin-1, and mast cell tryptase β2 significantly increased, and the protein levels of IL-5, IL-13, and OVA-specific immunoglobulin E (IgE) also significantly increased in the WAS group. Moreover, WAS significantly increased the intestinal permeability. The CRH-R1 antagonist significantly inhibited all changes induced by WAS. Psychological stress exacerbated ileal inflammation via the CRH-mast cell axis in an EoN mouse model.     

Correlation investigation between contact approach speed of handheld metal rod and discharge parameters from charged human body

Characteristic measurement of contact discharge currents are made through a hand-held metal rod from charged human body. Correlation coefficients are obtained, through Statistic Package for Social Science （SPSS）, for various charge voltages, which is based on the effect test of electrode contact approach speeds on discharge current parameters of current peaks, maximum rising slope and spark lengths. Discharge parameters at charge voltage 300V are independent on approach speed. For charge voltages equal to and higher than 500V, the contact approach speed has strong positive correlation with discharge parameters of the peak current and the maximum rising slope, whereas has strong negative correlation with the spark length.