Response analysis for identifying the origin of photo-modulated current contrasts in scanning tunneling microscopic imaging semiconductor surfaces

Inhomogeneities in semiconductor solids can be imaged by two-dimensional mapping of the amplitude of periodically modulated tip current in scanning tunneling microscopy that is induced by illumination of semiconductor samples with a chopped light. It has been shown that it is possible to distinguish between plural origins of the photo-modulated current by analyzing the response properties of the current signal. A judicial choice of the modulation frequency is important for the required contrasts to be obtained.     

Dielectric Dispersion of Polycrystalline Aluminum Nitride at Microwave Frequencies

Complex permittivity of polycrystalline AlN was measured over the frequency range 100 MHz to 13 GHz using reflection coefficient and cavity resonator methods. Dielectric relaxation peaks of loss tangent were observed in the frequency range 200 MHz to 3 GHz. The maximum value of loss tangent was ∼200 × 10⁻⁴. Relative permittivities decreased by ∼4% with increased frequency at the region of relaxation peaks. It was shown that these dispersion frequencies were inversely proportional to the grain sizes of AlN and independent of purities and processes. Model calculations for elastic vibration of a single-crystal grain of AlN were performed to investigate the origin of the dielectric dispersion due to piezoelectric effect. The calculated results of elastic sphere and 14-faced-polyhedron models showed a good quantitative agreement with the observed dispersion frequencies, which suggested that the dispersion was due to a piezoelectric vibration of a single grain of AlN ceramics at microwave frequencies.     

Effects of heated seats in vehicles on thermal comfort during the initial warm-up period

Eight subjects participated in a subjective experiment of eight conditions to investigate the effects of heated seats in vehicles on skin temperature, thermal sensation and thermal comfort during the initial warm-up period. The experimental conditions were designed as a combination of air temperature in the test room (5, 10, 15, or 20 °C) and heated seat (on/off). The heated seat was effective for improving thermal comfort during the initial warm-up period when air temperature was lower than 15 °C. Use of heated seats prevented decreases in or increased toe skin temperature. Heated seats also increased foot thermal sensation at 15 and 20 °C. Optimal thermal sensation in contact with the seat was higher when air temperature was lower. Optimal skin temperature in contact with the seat back was higher than that with the seat cushion. Moreover, these optimal skin temperatures were higher when air temperature was lower.     

A facile synthesis of hydro- and vinyl-functionalized di- and tetrasiloxanes and polyaddition via hydrosilylation

Summary Hydro- and vinyl-bifunctionalized di- or tetrasiloxane were synthesized by degradative cleavage of functional cyclic siloxanes with methyllithium followed by quenching with a functional chlorosilane, or by ring-opening of hexamethylcyclotrisiloxane (D₃) by functional alkyllithium followed by quenching with a functional chlorosilane. These bifunctionalized siloxanes were used as monomers in polyaddition with transition metal catalysts.     

Formation of Zirconia Solid Solutions Containing Alumina Prepared by New Preparation Method

In the system ZrO₂–Al₂O₃, a new method for preparing ZrO₂ solid solutions from ZrCl₄ and AlCl₃ using hydrazine monohydrate is investigated. c -ZrO₂ solid solutions containing up to ∼40 mol% Al₂O₃ crystallize at low temperatures from amorphous materials. The formation mechanism is discussed from IR spectral data. The values of the lattice parameter α increase linearly from 0.5072 to 0.5105 nm with increasing Al₂O₃ content. At higher temperatures, transformation of the solid solutions proceeds as follows: c ( SS ) → t ( ss ) → t ( ss ) +α-Al₂O₃→ m +α-Al₂O₃. m -ZrO₂–α-Al₂O₃ composite ceramics are fabricated by hot isostatic pressing for 2 h at 1250°C and 196 MPa. Microstructures and mechanical properties are examined, in connection with increasing Al₂O₃ content.     

Agglomeration control of hydroxyapatite nano-crystals grown in phase-separated microenvironments

Materials synthesis processes that require high temperatures consume large quantities of energy that generate an environmental burden. We attempted to synthesize hydroxyapatite (HAp) nano-crystals without firing or melting. “Water in oil” (W/O) emulsions were employed as microreactors for HAp formation. The surfactant-bounded water mediated HAp crystal nucleation, and HAp nano-crystallites were obtained. The obtained particles were aggregates composed of plate-like nano-crystals and monodisperse tiny crystals. Utilization of the W/O emulsions resulted in tunable nucleation frequency and the reactant provision, and yielded HAp nano-crystals with characteristic agglomeration properties.     

Study on high performance ice slurry formed by cooling emulsion in ice storage (discussion on adaptability of emulsion to thermal storage material)

This study focuses on an emulsion as a new thermal storage material for ice storage. Two types of emulsions were formed using an oil–water mixture with a small amount of additive. A silicone, light and lump oils were used. The water contents of the emulsions were 70, 80 and 90%. The additive was an amino group modified silicone oil. No depression of freezing point was observed for the emulsions because of their hydrophobic properties. In order to determine the structure of the emulsions, their electrical resistances were measured. Moreover, components of the liquids separating from the emulsions were analyzed. The results indicated that one emulsion was a W/O type emulsion, while the other was an O/W type. Finally, adaptability of the two emulsions to ice storage was discussed, it was concluded that a high performance ice slurry could be formed by the W/O type emulsion.     

Crystal orientation changes of Ag thin films on the Si(111) substrate due to tribo-assisted recrystallization

Crystal orientation changes of Ag thin films due to the tribo-assisted recrystallization have been studied using grazing incidence X-ray diffraction with synchrotron radiation. After preparation of an Si(111) √3 × √3-Ag surface, a 5-nm-thick Ag film was deposited on the surface at the substrate temperature of 303 K in an ultra-high vacuum chamber. The friction experiments were carried out using a diamond pin-on-plate type tribometer just after the Ag deposition in the same UHV chamber. We found that the coefficient of friction of the Ag films on the Si(111) √3 × √3-Ag surface decreases from 0.07 to 0.03, with increasing reciprocal sliding cycles. In synchronization with the coefficient change, Ag{100} grains are gradually disappearing. As a result, the Ag{111} grains cover the entire surface after 50 sliding cycles. Moreover, we found that the domain size of the Ag{111} grains increases with increasing reciprocal sliding cycles by measuring the rocking curve width. These results directly show that the Ag(111) plane is the sliding plane of friction and the coefficient of friction of Ag films is determined by the fraction of the Ag(111) grains in the Ag films. Moreover, to clarify the reaction between the Ag film and the Si substrate due to the tribo-assisted recrystallization, the substrate strain has been studied by an extremely asymmetric X-ray diffraction technique using synchrotron radiation.     

Enhanced dielectric properties of bismuth titanate/silver composites

Bismuth titanate (BiT) based composites containing silver particles are fabricated by a solution chemical process. Incorporation of silver particles does not result in unwanted reaction phase. SEM micrographs reveal fine silver particles distribute at BiT grain boundaries and into larger BiT plate-like grains. With the addition of silver, the dielectric constant increases up to ∼10 times higher than that of pure BiT ceramic, which can be attributed to the effective electric fields developed around the dispersed metal particles and the percolation effect. Additionally, the dielectric losses are significantly reduced by incorporating silver particles, and the values of BiT/Ag composites are lower than 0.5%. The dielectric properties of BiT/Ag composites are nearly frequency independent in the measured frequency range (1 kHz to 1 MHz).     

Effect of gravity on InGaSb crystal growth

The effect of gravity on dissolution of GaSb in InSb melt and growth of InGaSb was experimentally investigated. Experiments were carried out in a GaSb(seed)/InSb/GaSb(feed) sandwich system under an imposed temperature gradient. In the experiments, the GaSb feed crystal dissolved into the InSb melt to supply the required GaSb component for the growth of In_0.1Ga_0.9Sb crystal. Two parameters were considered: (1) the inclination angle (θ) of the sample for gravity as 0° and 53°, and (2) the sample diameter (D) as 9 mm and 5mm. When θ was 0°, the interface was almost flat, indicating that convection was axisymmetric and stable. Whereas the interface was distorted towards gravitational direction when θ was 53°, indicating that solutal convection was dominant. The decrease of growth temperature and sample diameter reduced the distortion of interface and the dissolution amount of GaSb feed. The homogeneous crystals were grown at the initial growth stage by supplying the GaSb component during growth.