Optimization of the sputter-deposited platinum cathode for a direct methanol fuel cell

The electrodes prepared by a sputtering method were evaluated as the cathodes for direct methanol fuel cells (DMFCs). Pt loading below 0.25 mg cm⁻² achieved higher mass activities than that of 0.5 mg cm⁻² prepared by the paste method, which was general conventional method. However, an increase in Pt loading reduced the catalyst activity for the oxygen reduction reaction (ORR). This result may suggest an increase in only electrochemically inactive Pt. Pt utilization efficiency can be found about ten times higher at Pt loading of 0.04 mg cm⁻². Moreover, addition of Nafion to sputter-deposited Pt cathodes is found possible to improve the catalyst activity for the ORR, but the excess Nafion over the optimum condition reduces the active sites.     

Sintering Kinetics at Isothermal Shrinkage: II, Effect of Y2O3 Concentration on the Initial Sintering Stage of Fine Zirconia Powder

The shrinkage behavior of fine zirconia powders containing 2.9 and 7.8 mol% Y₂O₃ was investigated to clarify the effect of Y₂O₃ concentration on the initial sintering stage. The shrinkage of powder compact was measured under both conditions of constant rates of heating (CRH) and constant temperatures. CRH measurements revealed that when the Y₂O₃ concentration of fine zirconia powder increased, the starting temperature of shrinkage shifted to a high temperature. Isothermal shrinkage measurements revealed that the increase in Y₂O₃ concentration causes the shrinkage rate to decrease. The values of activation energy ( Q ) and frequency-factor term (β₀) of diffusion at initial sintering were estimated by applying the sintering-rate equation to the isothermal shrinkage data. When the Y₂O₃ concentration increases, both Q and β₀ of diffusion increase. It is, therefore, concluded that the increase in Y₂O₃ concentration of fine zirconia powder decreases the shrinkage rate because of increasing Q of diffusion at the initial stage of sintering.     

Temperature Dependence of Young's Modulus and Internal Friction in Alumina, Silicon Nitride, and Partially Stabilized Zirconia Ceramics

The temperature dependence of Young's modulus and internal friction (Q⁻¹)in alumina, silicon nitride, and partially stabilized zirconia (Y-PSZ) ceramics was studied. Little change in Q⁻¹ was found for alumina, whereas Q⁻¹ for silicon nitride ceramics increased above 700°C. The Q⁻¹ of Y-PSZ increased markedly with increasing temperature up to a peak at ∼200°C.     

Reaction products of α-tocopherol with methyl linoleate-peroxyl radicals

α-Tocopherol was reacted with methyl linoleateperoxyl radicals at 37°C. The peroxyl radicals were generated by the reaction of methyl linoleate with a free radical initiator, 2,2′-azobis(2,4-dimethylvaleronitrile). The primary products of α-tocopherol with methyl linoleate-peroxyl radicals were isolated by reversephase and normal-phase high performance liquid chromatography (HPLC), and their structures were characterized by ultraviolet (UV), infrared (IR),¹H and¹³C nuclear magnetic resonance (NMR) and mass spectrometry (MS). There were four stereoisomers of methyl 13-(8a-peroxy-α-tocopherone)-9(Z),11(E)-octadecadienoate and four stereoisomers of methyl9-(8a-peroxy-α-tocopherone)-10(E),12(Z)-octadecadienoate.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

Liquid crystalline side-chain polysiloxanes containing mesogenic groups attached by esterification

Summary Liquid crystalline side-chain polysiloxanes were prepared without metal complex catalyst. Mesogenic groups such as cholesteryl, 4-cyano-4-biphenyl and 4-methoxy-4-biphenyl group were introduced into polysiloxane by esterification and from DSC measurements they were compatible with other liquid crystalline polysiloxanes reported previously.     

Hot dip fine Zn and Zn-Al alloy double coating for corrosion resistance at coastal area

A new hot dip Zn-7Al alloy coating was performed on a structural steel by double coating of fine Zn and Zn-7 wt.% Al alloy, to prevent severe corrosion in coastal area. The alloy-coated steels were exposed to seaside, quasi-industrial, and rural districts to compare with conventional Zn coating. Double coating was significantly effective in preventing corrosion, particularly in a seaside. It was estimated from the exposure test for 10 years that the life of the Zn-7Al alloy-coated steel would be almost four times that of the Zn-coated steel in the seaside. A bending test showed that no exfoliation occurred at the interface between the coated alloy and substrate steel. TEM observation revealed that the excellent adhesiveness of the doubly coated fine Zn and Zn-7Al alloy to the steel substrate was due to formation of the interface region consisting of heterogeneous fine phase mixture of zinc, aluminium and iron.     

Two‐way multi‐view 2‐D/3‐D display combining LC lens and HVxDP panel using novel pixel arrangement

We have developed a two‐way multi‐view 2‐D/3‐D display combining a liquid crystal lens and horizontally and vertically x times‐density pixels (HVxDP) arrangement. The two‐way multi‐view display features the same display resolution in 2‐D and 3‐D modes and a quite small color moiré for landscape and portrait, respectively, when using the HVxDP arrangement. In this paper, we realized suitable 3‐D properties for achieving a good balance between 3‐D moiré and 3‐D crosstalk for landscape and portrait by a two‐way liquid crystal lens with two kinds of focal lengths for the edge part and the center part of the lens.     

Parallelized fusion visualization system

The speed-up of supercomputers has increased the complexity of simulations. To analyze such kind of data, we believe that new types of visualization software are needed. Therefore, we have been developing a visualization system called “Fusion Visualization”, and the progresses were reported in the AROB 18th and 19th International Symposiums. We introduced the overall concept at the AROB 18th International Symposium, and then demonstrated a sample of flow visualization in a blood vessel in the AROB 19th International Symposium. To extend our system to enable the handling of larger data, we have implemented the proposed system on a parallelized visualization system; AVS/Express PCE (Parallel Cluster Edition). This paper describes the implementation and the benchmark results.