Mechanical properties and morphology of crosslinked PP/PE blends and PP/PE/propylene–ethylene copolymer blends

Blending is an effective method for improving polymer properties. However, the problem of phase separation often occurs due to incompatibility of homopolymers, which deteriorates the physical properties of polyblends. In this study, isotactic polypropylene was blended with low-density polyethylene. Crosslinking agent and copolymers of propylene and ethylene (either random copolymer or block copolymer) were added to improve the interfacial adhesion of PP/LDPE blends. The tensile strength, heat deflection temperature, and impact strength of these modified PP/PE blends were investigated. The microstructures of polyblends have been studied to interpret the mechanical behavior through dynamic viscoelasticity, wide-angle X-ray diffraction, differential scanning calorimetry, picnometry, and scanning electron microscopy. The properties of crosslinked PP/PE blends were determined by the content of crosslinking agent and processing method. For the material blended by roll, a 2% concentration of peroxide corresponded to a maximum tensile strength and minimum impact strength. However, the mechanical strength of those products blended by extrusion monotonously decreased with increasing peroxide content because of serious degradation. The interfacial adhesion of PP/PE blends could be enhanced by adding random or block copolymer of propylene and ethylene, and the impact strength as well as ductility were greatly improved. Experimental data showed that the impact strength of PP/LDPE/random copolymer ternary blend could reach as high as 33.3 kg · cm/cm; however, its rigidity and tensile strength were inferior to those of PP/LDPE/block copolymer blend.     

The morphology and conductivity of polypyrrole/polyurethane alloy films

Polymeric composites with conductivities ranging from 10^–4 to 1 S cm^–1 were prepared by electrochemically polymerizing pyrrole in a matrix of polyurethane. The polypyrrole/polyurethane alloy films obtained were characterized by element analysis, electron microscopy and electrical conductivity measurements. The morphology of the films depended on the solvent, the electrolyte and the current density. The mechanism of the electrochemical polymerization showed that PPy grew in a treelike structure, with molecular chains extending from the electrode surface into the solution. The transition temperature of the PPy/PU increased with the PPy content.     

Graft polymerization of vinyl acetate onto granular starch: Comparison on the potassium persulfate and ceric ammonium nitrate initiated system

This work was undertaken to discuss in depth the vital differences in the morphological development during synthesis, and properties of starch‐g‐poly‐(vinyl acetate) copolymers using two different initiators, potassium persulfate (KPS) and ceric ammonium nitrate (CAN). KPS‐initiated system gave relatively low values of grafting ratio and grafting efficiency, indicating a great tendency for the formation of poly(vinyl acetate) homopolymer (PVAc). Yet, higher values were seen for the CAN‐initiated system. Transmission electron microscope observations indicated a relatively broad distribution of latex particles for the KPS‐initiated system. The surface potential of latex particles was about ?3.5 mV, which turned out to be insufficient to maintain stability of latex particles. On the other hand, a uniform particle size distribution was found for the CAN‐initiated system, as the surface potential of latex particles was 21.5 mV. Moreover, radicals on starch molecules were generated directly through a redox reaction with positively charged ceric ion. The hydrophobic PVAc chains were thus grafted on starch, resulting in an amphiphilic graft copolymer, which provides a sufficient stabilization degree as a role of surfactant to render a relatively uniform distribution of latex particles. The synthesized starch‐g‐poly(vinyl acetate) copolymers were further converted to starch‐g‐poly(vinyl alcohol) through saponification, which were subjected to evaluations regarding the biodegradation and cell culture capability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3017–3027, 2006     

Morphology and characterization of conductive films based on polyaniline‐coated polystyrene latexes

The polyaniline (PANI)‐coated polystyrene (PS) latexes were synthesized, and the electrically conductive films were prepared thereafter. The weight ratio of PANI was 5%. Thermal analysis of the latices was performed using DSC and TGA. In this study, the electrically conductive films were prepared above the PS glass transition temperature (T_g). During the film formation, the effects of the annealing temperature and atmosphere (air or N₂) on the film resistance were investigated. In addition, the film morphology was observed utilizing scanning electron microscopy. The film resistance decreased in the initial heating stage due to the increasing temperature and the compaction of film. Then the film resistance increased with further annealing due to the aging of PANI. Typically, the film resistance was about 6000 Ω/sq, and the conductivity was 0.3 S/cm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5406–5413, 2006     

The Effects of Experience and Strategy on Visual Attention Allocation in an Automated Multiple-Task Environment

Operators and users interacting with computer environments often have to deal with multiple tasks at once, responding to each in series. Diagnostic automation, that is, automation that alerts users when and where to look, has been suggested to support the unique challenges of multiple task environments: activating tasks, switching between tasks, and tasks interfering with each other. Automation is not always reliable, however. Because of the common interaction with novel systems and the importance of training, the Simultaneous Task Environment Platform program—a multiple-task environment—was developed to understand the effects of experience on interaction with these automation-supported systems, as well as what strategies were developed. It was found that participants became more efficient with experience only when they interacted with higher reliability automation. Furthermore, the strategies participants developed focused on the differences between tasks and patterns across those tasks. Automated systems training should be sure to employ these findings.     

Lamellar Morphology of Poly(3-hydroxybutyrate)/Poly(ethylene oxide) Blends as Studied via Small Angle X-ray Scattering

The lamellar morphology of a melt-miscible blend consisting of two crystalline constituents, poly(3-hydroxybutyrate) (PHB) and poly(ethylene oxide) (PEO) have been investigated by means of small angle X-ray scattering (SAXS). The blend was a crystalline/amorphous system when temperatures lay between the melting point of PEO (ca. T _m ^PEO=60C) and that of PHB (ca. T _m ^PHB=170C), while it became a crystalline/crystalline system below T _m ^PEO. The crystalline microstructures of the blends were induced by two types of crystallization history, i.e. one-step and two-step crystallizations. In the one-step crystallization, the blends were directly quenched from the melt to room temperature to allow simultaneous PHB and PEO crystallization. The two-step crystallization involved first cooling to 70C to allow PHB crystallization for 72 h followed by cooling to room temperature (ca. 19C) to allow PEO crystallization. In the crystalline/crystalline state, two scattering peaks have been observed in the Lorentz-corrected SAXS profiles, irrespective of the crystallization histories, meaning that crystallization created separate PHB and PEO lamellar stack domains. One-step crystallization yielded lamellar stack domains containing almost pure PHB and PEO lamellae. Two-step crystallization generated almost pure PHB lamellar domains and the PEO lamellar domains with inserted PHB lamellae. In the crystalline/amorphous state, the composition dependence of the amorphous layer thickness (l _a), the presence of zero-angle scattering, and the volume fraction of the PHB lamellar stack (_s) revealed that both one-step and two-step crystallizations, generated the interfibrillar segregation morphology, where the extent of interfibrillar segregation of amorphous PEO increased with increasing PEO content.     

Preparation and properties of nadic‐end‐capped cyclotriphosphazene‐containing polyimide/carbon fiber composites

New novel fire‐resistant and heat‐resistant cyclotriphosphazene‐containing polyimide resins were prepared in situ by the polymerization of (p‐aminophenoxy)(phenoxy)cyclotriphosphazenes with 3,3′,4,4′‐benzophenonetetracarboxylic acid or 3,3′,4,4′‐diphenylsulfonetetracarboxylic acid and a crosslink agent, 5‐norbornene‐2,3‐dicarboxylic acid and were used as polymer matrix compositing with a woven carbon fiber to prepare nadic‐end‐capped cyclotriphosphazene‐containing polyimide/carbon fiber composites. The thermal stability, flame retardance, morphology of the surface fracture, and some physical properties of the composites were investigated by thermogravimetric analysis, scanning electron microscopy, and a material testing system, respectively. The composites had good thermal stability, flame retardance, and mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 810–818, 2003     

Dispersion of carbon nanotubes in low pH aqueous solutions by means of alumina-coated silica nanoparticles

A novel noncovalent and inorganic method was used to disperse multiwalled carbon nanotubes (MWCNTs) in aqueous solutions through alumina-coated silica (ACS) nanoparticle halos. MWCNTs were directly dispersed into a highly charged ACS nanoparticle aqueous solution without functionalization of their surfaces. The dispersed MWCNTs were characterized by transmission electron microscopy and atomic force microscopy. Raman spectroscopy of MWCNTs prepared from dispersion in the ACS solution revealed reduced bundling compared to the corresponding untreated MWCNTs. The characteristic Raman peak at about 1570 cm⁻¹, corresponding to the G band, shifted to a higher wavenumber with a narrower peak. It was possible to disperse up to 20 mg/mL of MWCNTs in a 1 wt% ACS nanoparticle aqueous solution at pH 2. This homogeneous MWCNT-ACS aqueous solution was stable for weeks after ultrasonication.     

Effects of oxidation and particle shape on critical volume fractions of silver‐coated copper powders in conductive adhesives for microelectronic applications

The effects of oxidation and particle shape on critical volume fractions of silver‐coated copper powders in conductive adhesives are investigated. Silver‐coated copper powders with spherical and flake‐shaped particles were oxidized at temperatures of 30°C, 175°C and 240°C for two hours and dispersed in an epoxy matrix. As silver‐coated copper powders are oxidized at 30°C and 175°C, the critical volume fractions of the conductive adhesives are slightly affected by oxidation and particle shape at these temperatures. As the oxidation temperature approaches 240°C, the critical volume fractions of the conductive adhesives are strongly affected by oxidation temperature and particle shape, owing to the formation of oxides such as Cu₂O on the surface of silver‐coated copper powder—Cu diffuses from the interior to the surface of silver‐coated copper powder and reacts with the oxygen in the air. Silver‐coated copper powder with flake‐shaped particles shows lower critical volume fractions in conductive adhesives than silver‐coated copper powder with spherically shaped particles. Polym. Eng. Sci. 44:2075–2082, 2004. © 2004 Society of Plastics Engineers.     

A study of optimal viewing distance in a parallax barrier 3D display

The optimal viewing distance was proposed as a parameter for designing a parallax barrier 3D display. It can be designed based on simple geometric method and by considering the pitches of image display pixels and parallax barrier, or even including the aperture ratios of the image display pixels and parallax barrier. It can be analyzed by using ray tracing method. By considering the optical refraction index of the cover glass, the angular behavior of the system becomes more realistic; however, the geometric method is difficult to be used. We propose a revised method for estimating the view distance and angular behavior. In this paper, we have demonstrated a designated eye position (DEP) for each view and shown that multiple DEPs make a circular curve around the center of the display. We prove the new concept by comparing the optical ray tracing calculations and optical measurement.