Electron‐beam deposition of MgO on plastic substrate and manufacturing flexible flat fluorescent lamp

Abstract— A flexible fluorescent lamp that utilizes the same plasma discharge mode as in PDPs has been manufactured. The structure of the flexible lamp is simple and easy to manufacture. All‐plastic materials including plastic substrates, barrier ribs (spacers), and sealants for low‐temperature manufacturing processing have been adopted except for the phosphor and MgO thin film. The MgO thin films were coated on the plastic substrates as a protection layer against the plasma discharge. The adhesion and biaxial texture of MgO thin film deposited on the plastic substrates, poly‐ethyle‐nenaphthalate (PEN) and polycarbonate (PC), at low temperature (100–180°C) has been characterized. The MgO film on PEN shows good adhesion under a repeated bending test. The manufactured flexible lamp consists of two plastic substrates of about 3 in. on the diagonal, barrier rib (spacer), and external ITO electrodes. The Ne‐Xe (5%) gas mixture at 100–200 Torr was used for the discharge gas. A maximum surface luminance of about 100 cd/m² was achieved for a 1 ‐kHz AC pulse.     

Preparation and characterization of nanoporous polyimide films from triblock copolyimides

Nanoporous polyimide films were prepared from triblock copolyimides. A thermally labile polymer, poly(propylene glycol), was incorporated into polyimides based on 4,4-(hexafluoroisopropylidene)diphthalic anhydride to obtain triblock copolyimides. Nanofoams were formed by thermolysis of the labile block. The thermal properties of the copolymers were investigated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The nanopores were characterized by scanning electron microscopy (SEM).     

Effect of deposition temperature on dielectric properties of PECVD Ta2O5 thin film

Tantalum oxide film formation by plasma-enhanced chemical vapour deposition (PECVD) using TaCl₅ as a source material was examined. The effects of deposition temperature on the formation, structure and electric properties of the Ta₂O₅ film were investigated for Al/Ta₂O₅/ p-Si (MTS) capacitors. The deposition rate and refractive index increased with increasing deposition temperature. It was found that the structure of Ta₂O₅ deposited by PECVD was amorphous as-deposited. However, crystalline -Ta₂O₅ of hexagonal structure was formed by a 700 °C, 1 h heat treatment in argon. Capacitance and relative dielectric constant of the PECVD Ta₂O₅ were found to be 2.54 fF m^–2 and 23.5, respectively. The PECVD films obtained in this study have higher dielectric constants and remarkably better general film characteristics than those obtained by other deposition methods.     

Implementation of mmWave long-range backhaul for UAV-BS

Uncrewed aerial vehicles (UAVs) have become a vital element in nonterrestrial networks, especially with respect to 5G communication systems and beyond. The use of UAVs in support of 4G/5G base station (uncrewed aerial vehicle base station [UAV-BS]) has proven to be a practical solution for extending cellular network services to areas where conventional infrastructures are unavailable. In this study, we introduce a UAV-BS system that utilizes a high-capacity wireless backhaul operating in millimeter-wave frequency bands. This system can achieve a maximum throughput of 1.3 Gbps while delivering data at a rate of 300 Mbps, even at distances of 10 km. We also present the details of our testbed implementation alongside the performance results obtained from field tests.     

Effects of material combination on laser beam drilling of a metal foil using a cover plate

This research investigated the microdrilling characteristics of metal foils depending on the materials of the cover plates and metal foils in the cover plate-laser beam machining (c-LBM) process, which is a method to achieve better quality in metal foil machining with a given piece of equipment. Laser beam drilling using a nanosecond pulsed laser was carried out on 10-µm-thick stainless steel 304 (STS304), nickel, and copper foils with 100-µm-thick cover plates of each material. Consequently, STS304 was found to be an effective cover plate material for reducing the hole diameter and spatter deposition on metal foils. Compared to the results without using a cover plate, the average hole diameter and the area of spatter deposition decreased by up to 77% and 96%, respectively, by using the STS304 cover plate. Meanwhile, the thermal deformation of the STS304 and nickel foils was prevented by using a cover plate, while the copper foil was barely deformed even without a cover plate. Lastly, it was remarkable that the copper foil was drilled with approximately 67% lower pulse energy than the effective minimum pulse energy required to drill it by using the STS304 cover plate, resulting in a smaller hole with little spatter.     

Carbon Nanodot‐Sensitized Modulation of Alzheimer's β‐Amyloid Self‐Assembly,Disassembly, and Toxicity

The self‐assembly of amyloidogenic peptides into β‐sheet‐rich aggregates is a general feature of many neurodegenerative diseases, including Alzheimer's disease, which signifies the need for the effective attenuation of amyloid aggregation toward alleviating amyloid‐associated neurotoxicity. This study reports that photoluminescent carbon nanodots (CDs) can effectively suppress Alzheimer's β‐amyloid (Aβ) self‐assembly and function as a β‐sheet breaker disintegrating preformed Aβ aggregates. This study synthesizes CDs using ammonium citrate through one‐pot hydrothermal treatment and passivates their surface with branched polyethylenimine (bPEI). The bPEI‐coated CDs (bPEI@CDs) exhibit hydrophilic and cationic surface characteristics, which interact with the negatively charged residues of Aβ peptides, suppressing the aggregation of Aβ peptides. Under light illumination, bPEI@CDs display a more pronounced effect on Aβ aggregation and on the dissociation of β‐sheet‐rich assemblies through the generation of reactive oxygen species from photoactivated bPEI@CDs. The light‐triggered attenuation effect of Aβ aggregation using a series of experiments, including photochemical and microscopic analysis, is verified. Furthermore, the cell viability test confirms the ability of photoactivated bPEI@CDs for the suppression of Aβ‐mediated cytotoxicity, indicating bPEI@CDs' potency as an effective anti‐Aβ neurotoxin agent.     

Viscosity of high-entropy melts in the Cu—Bi—Sn—In—Pb system

High-entropy melts in the Cu—Bi—Sn—In—Pb system have been studied by viscosity measurements during heating and subsequent cooling. The experimental data have been used to determine the temperatures at which microinhomogeneities in the melts irreversibly disappear.     

Silver Nanoflower Decorated Graphene Oxide Sponges for Highly Sensitive Variable Stiffness Stress Sensors

Soft conductive materials should enable large deformation while keeping high electrical conductivity and elasticity. The graphene oxide (GO)‐based sponge is a potential candidate to endow large deformation. However, it typically exhibits low conductivity and elasticity. Here, the highly conductive and elastic sponge composed of GO, flower‐shaped silver nanoparticles (AgNFs), and polyimide (GO‐AgNF‐PI sponge) are demonstrated. The average pore size and porosity are 114 µm and 94.7%, respectively. Ag NFs have thin petals (8–20 nm) protruding out of the surface of a spherical bud (300–350 nm) significantly enhancing the specific surface area (2.83 m² g^?1). The electrical conductivity (0.306 S m^?1 at 0% strain) of the GO‐AgNF‐PI sponge is increased by more than an order of magnitude with the addition of Ag NFs. A nearly perfect elasticity is obtained over a wide compressive strain range (0–90%). The strain‐dependent, nonlinear variation of Young's modulus of the sponge provides a unique opportunity as a variable stiffness stress sensor that operates over a wide stress range (0–10 kPa) with a high maximum sensitivity (0.572 kPa^?1). It allows grasping of a soft rose and a hard bottle, with the minimal object deformation, when attached on the finger of a robot gripper.