A simple one-cycle power supply for approach to saturation studiesin soft magnetic polycrystalline toroidal samples

The ring shape is a good solution to the study of the magnetization processes of magnetic materials because demagnetizing fields are easily avoided. However, when small samples are investigated, the magnitude of the field applied is necessarily limited by the low number of primary winding turns, and by the cross section of the wire itself. The use of sequential-type techniques for high current supply allows this problem to be avoided. One-cycle power production from the 50 Hz AC-line voltage is a simple example of such techniques. An electronic device designed around a commercial integrated circuit is described. A full period of current of 20-ms duration is applied to the load with a magnitude ranging from 0 to 100 A. Magnetization parameters of soft polycrystalline ring ceramics approaching the saturation region are studied as an application. The fitness to measure such characteristic parameters as saturation magnetization and magnetic hardness is shown     

Plastic flow and fracture of Pd40Ni40P20 metallic glass under an indentor

The geometry of plastic flow under spherical and Vickers indentors in Pd₄₀Ni₄₀P₂₀ metallic glass has been investigated by sectioning and etching. The surface pile-ups and slip lines around the indentations are found to be only a small part of the total deformation. Beneath the surface extensive plastic zones are formed in which material is moved radially away from the indentor, but this movement is produced by slip on surfaces of high shear stress rather than by direct radial flow or compaction. Networks of cracks or incipient cracks also form around an indentation but are not normally visible until the material is etched.     

Wide frequency range sine wave VCO with a tunable inductor andcapacitor

A voltage-controlled oscillator (VCO) with sine wave output has been built using a tunable inductor along with a tunable capacitor to operate at frequencies ranging from 100 kHz to over 20 MHz. The method of tuning the inductor by changing the permeability of its ferrite core and the ability to extend the frequency response of the core are discussed. Dynamic characteristics of the VCO are explained with examples of a parallel and series tank implementation     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Imperfections and impurity phases in flux grown RCrO3 (R = La,Yb) single crystals

Results of scanning electron microscopy (SEM) and energy dispersive X-ray analytical (EDAX) investigations, conducted on some elevated structures displayed by flux grown rare earth orthochromite, RCrO₃ (R = La, Yb) crystals, are presented. The peculiar structures exhibited by crystal surfaces indicate imperfections and impurity phases. EDAX of elevated structures reveals the various phases to be composed of lead associated materials which may probably be either Pb₂CrO₅ or Pb₂OF₂ (flux). Other secondary crystallization of impurity phases, ROF (R = La, Yb) is illustrated in the case of RCrO₃ (R = La, Yb) crystals. The elevated structures illustrate their non-stoichiometric behaviour. Precipitation of impurity phases and formation of imperfections during the growth of RCrO₃ (R = La, Yb) crystals and their effect on the crystalline quality is discussed.     

Influence of ash deposits on the heat resistance of materials for gas turbine engine blades

Leningrad. Translated from Problemy Prochnosti, No. 1, pp. 71–76, January, 1989.     

Random errors caused by temperature in magnitude of principal strains evaluated ith 3-element strain gauge rosettes

The effects of the uncertainties associated ith the apparent strain and gauge factor data, given by the manufacturer, in the evaluation of principal strains are examined. Principal strains are obtained by a reduction of the strains measured ith electrical resistance strain gauge rectangular or delta rosettes. The theoretical analysis points out the relevance of the effects caused.