Calibrating high-vacuum gauges

Translated from Izmeritel'naya Tekhnika, No. 6, pp. 19–20, June, 1989.     

Craze yielding and fracture mechanism in PE/PS/PE laminated films

The change in polystyrene (PS) layer thickness, which has been simultaneously determined during post-yield deformation, shows that crazing is the basic mechanism of toughening in all laminated films, and that shear deformation supplements the contribution of crazing especially for samples with high polyethylene (PE) volume fractions. Crazes formed in PS layers in the laminated films are slender and regular compared with the short and lenticular crazes formed in bulk PS film. When PE volume fraction increased, craze advance speed decreased because of the reduction of the stress concentration effect at craze tips. The life-time of the first mature craze to be formed at a given strain rate increased with PE volume fraction because the PE supporting the mature crazes could effectively inhibit craze rupture and blunt out the propagating crack by absorbing the stored elastic energy in the PS layer that would have been dissipated as fracture surface energy.     

Wide frequency range sine wave VCO with a tunable inductor andcapacitor

A voltage-controlled oscillator (VCO) with sine wave output has been built using a tunable inductor along with a tunable capacitor to operate at frequencies ranging from 100 kHz to over 20 MHz. The method of tuning the inductor by changing the permeability of its ferrite core and the ability to extend the frequency response of the core are discussed. Dynamic characteristics of the VCO are explained with examples of a parallel and series tank implementation     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Imperfections and impurity phases in flux grown RCrO3 (R = La,Yb) single crystals

Results of scanning electron microscopy (SEM) and energy dispersive X-ray analytical (EDAX) investigations, conducted on some elevated structures displayed by flux grown rare earth orthochromite, RCrO₃ (R = La, Yb) crystals, are presented. The peculiar structures exhibited by crystal surfaces indicate imperfections and impurity phases. EDAX of elevated structures reveals the various phases to be composed of lead associated materials which may probably be either Pb₂CrO₅ or Pb₂OF₂ (flux). Other secondary crystallization of impurity phases, ROF (R = La, Yb) is illustrated in the case of RCrO₃ (R = La, Yb) crystals. The elevated structures illustrate their non-stoichiometric behaviour. Precipitation of impurity phases and formation of imperfections during the growth of RCrO₃ (R = La, Yb) crystals and their effect on the crystalline quality is discussed.     

Influence of ash deposits on the heat resistance of materials for gas turbine engine blades

Leningrad. Translated from Problemy Prochnosti, No. 1, pp. 71–76, January, 1989.     

Near-resonance oscillations of a nonsymmetric nonlinear system with a crack

The Malkin method, which was developed to construct a single unique resonance solution of nonlinear equations, is generalized for the case of the derivation of all stationary solutions in the near-resonance zone, and also for transient oscillations.Kiev Polytechnic Institute. Translated from Problemy Prochnosti, No. 10, pp. 108–112, October, 1989.     

Toughening of Dental Porcelain by Tetragonal ZrO2 Additions

The effect on mechanical behavior of ZrO₂ additions to a dental porcelain was investigated. The ZrO₂ was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO₂ was retained in the tetragonal form after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance.