High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.     

Effect of irradiation with low-energy Ar ions on the characteristics of the working and rear sides of single-crystal GaAs substrate

Contactless methods were used to study the characteristics of the front and rear sides of single-crystal GaAs wafers whose rear side was irradiated with low-energy Ar ions. Variations in the optical and photoelectric properties of irradiated and unirradiated sides were detected. A solitonic mechanism for the penetration of defects into the crystal bulk is suggested.     

Wavelength stabilizer for telecommunication lasers: design and optimization

We introduce a novel method for the wavelength stabilization of semiconductor lasers for telecommunications. The approach is based on a wavelength-sensitive photodetector which, in a feedback system, generates an error signal apt to tune the source to the desired value. We extensively investigate the influence of various design parameters on performance figures such as tunability, steady-state error, and temperature dependence, as well as fabrication tolerances. The results are compared with standard specifications for wavelength-division-multiplexed optical communications with various channel spacings.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

QoS enhancement for adaptive streaming services over WCDMA

This paper presents a new method to adapt the quality-of-service (QoS) in a wideband code-division multiple-access (WCDMA) system, called radio network feedback (RNF). The concept of RNF is in general applicable to all the services requiring a minimum quality (i.e., non best effort) and in this paper, the focus is on streaming. In this context, RNF makes it possible for a streaming server to adapt its source bit rate to a WCDMA radio link, whose bandwidth may vary in time due, for example, to decongestion/congestion situations over the air interface or to handover. This is very beneficial for the end user as it allows to increase the bandwidth (i.e., the quality) when possible and to decrease it (instead of just dropping the service) when needed. RNF was compared with Client-based adaptation solutions. Simulation results show that RNF is fast and accurate and performs better than Client-based adaptation. For example, rebuffering occurs only with Client-based method. Moreover, with RNF the up-switch is performed only when needed, whereas the up-switch performed by means of the Client-based method is often erroneous and may annoy the end user.     

High voltage (>1kV) and high current gain (32) 4H-SiC power BJTs using Al-free ohmic contact to the base

This letter reports the design and fabrication of 4H-SiC bipolar junction transistors with both high voltage (>1kV) and high dc current gain (/spl beta/=32) at a collector current level of I/sub c/=3.83A (J/sub c/=319 A/cm/sup 2/). An Al-free base ohmic contact has been used which, when compared with BJTs fabricated with Al-based base contact, shows clearly improved blocking voltage. A specific on-resistance of 17 m/spl Omega//spl middot/cm/sup 2/ has been achieved for collector current densities up to 289 A/cm/sup 2/.     

Design of radiation-emission measurements of an air-traffic surveillance radar

The current work presents the procedure of designing and carrying out measurements of radiation emission from an air-traffic surveillance radar. The system requirements are first given, and then the equipment used is described. The steps to determine the operating characteristics of the radar are specified in detail. The necessary methods for manual power measurements and calculations are next explained. Since the final measurement system was fully automated, its main features (topology, protocol of operation) are also given. Finally, some measurement results taken during the initial phase of system operation are presented and discussed.     

An adaptive Gaussian model for satellite image deblurring

The deconvolution of blurred and noisy satellite images is an ill-posed inverse problem, which can be regularized within a Bayesian context by using an a priori model of the reconstructed solution. Since real satellite data show spatially variant characteristics, we propose here to use an inhomogeneous model. We use the maximum likelihood estimator (MLE) to estimate its parameters and we show that the MLE computed on the corrupted image is not suitable for image deconvolution because it is not robust to noise. We then show that the estimation is correct only if it is made from the original image. Since this image is unknown, we need to compute an approximation of sufficiently good quality to provide useful estimation results. Such an approximation is provided by a wavelet-based deconvolution algorithm. Thus, a hybrid method is first used to estimate the space-variant parameters from this image and then to compute the regularized solution. The obtained results on high resolution satellite images simultaneously exhibit sharp edges, correctly restored textures, and a high SNR in homogeneous areas, since the proposed technique adapts to the local characteristics of the data.     

The Effect of Moisture Content on the Conversion of Ergosterol to Vitamin D in Shiitake Mushrooms

The distribution of ergosterol in different parts of shiitake mushrooms was studied in order to optimize the conversion of ergosterol to vitamin D₂ during drying. The effect of moisture on the conversion of ergosterol to vitamin D₂ was also investigated by adjusting the moisture content of fresh mushrooms to different levels in a large vacuum desiccator and subjecting them to UV irradiation at 290-320 nm wavelength, for 2 h. The moisture, ergosterol and vitamin D₂ contents were determined using standard procedures. It was found that the ergosterol content on a dry matter basis of fresh shiitake mushroom was highest in the gills (10.6 ± 0.99 mg/g DM), followed by the cap or pileus (5.34 ± 0.64 mg/g DM) and was least in the stalk or stipe (2.97 ± 0.56). The moisture content had a marked influence on the conversion of ergosterol to vitamin D₂, the best conversion taking place at a moisture content of about 70% on a wet basis.