Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

Heat Transfer by Radiation through a Vapor Gap under Conditions of Film Boiling of Liquid

Theoretical models of heat transfer by radiation through a vapor gap under conditions of film boiling of liquid are treated, namely, a general wave model for a gap of arbitrary thickness and an approximate model of geometrical optics. Calculations are performed of heat transfer by radiation under conditions of film boiling of water on hot surfaces of refractory metal and molten oxide. Practical recommendations are given to calculate the distribution of the power of absorbed radiation in a water layer.     

A novel driver assist stability system for all-wheel-drive electric vehicles

A novel driver-assist stability system for all-wheel-drive electric vehicles is introduced. The system helps drivers maintain control in the event of a driving emergency, including heavy braking or obstacle avoidance. The system comprises a fuzzy logic system that independently controls wheel torque to prevent vehicle spin. Another fuzzy wheel slip controller is used to enhance vehicle stability and safety. A neural network is trained to generate the required reference for yaw rate. Vehicle true speed is estimated by a sensor data fusion method. The intrinsic robustness of fuzzy controllers allows the system to operate in different road conditions successfully. Moreover, the ease of implementing fuzzy controllers gives a potential for vehicle stability enhancement.     

Robust dual-quantisation multibit sigma-delta modulator

A new dual-quantisation sigma-delta modulator is proposed, which introduces an additional feedback path in the input of the second integrator. In this way, unlike other dual-quantisation architectures, larger signal-to-noise ratios can be obtained by means of aggressive noise-shaping, like in a conventional multibit modulator. The proposed modulator is also shown to be more robust against non-idealities than other dual-quantisation architectures.     

Optimal space-time constellations from groups

We consider the design of space-time constellations based on group codes for fading channels with multiple transmit and receive antennas. These codes can be viewed as multiantenna extensions of phase-shift keying (PSK), in the sense that all codewords have equal energy, all are rotations of a fixed codeword, and there is a simple differential transmission rule that allows data to be sent without channel estimates at the transmitter or receiver. For coherent detection, we show that all optimal full-rank space-time group codes are unitary (each code matrix has equal-energy, orthogonal rows). This leads to a simpler code design criterion and suggests that unitary codes may play an important role in coherent as well as noncoherent communication. For any number of transmit antennas t, we then use the design criterion to characterize all full-rank unitary space-time group codes of minimum block length (also t) which have 2/sup p/ codewords. These results allow us to characterize all optimal 2/sup p/-ary unitary group codes with square code matrices. This restricted class of block codes matches the class proposed for differential modulation by Hughes (see IEEE Trans. Inform. Theory, vol.46, p.2567-78, Nov. 2000), and by Hochwald and Sweldens (see IEEE Trans. Commun., vol.48, p.2041-2052, Dec. 2000).     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed