Virtual circuit connection method for RSVP multicasting supportingheterogeneous receivers on the ATM network

The authors suggest a novel virtual circuit connection method based on the reverse traversing technique to minimise the waste of network bandwidth resources, when the Internet protocol multicast is interoperated using the resource reservation protocol over an asynchronous transfer mode network. Simulation results show that, as the number of receivers increases, the bandwidth requirements on all links of the network of the proposed scheme become more advantageous than those of other conventional methods     

Directly Compressible Acetaminophen Compositions Prepared by Fluidized-Bed Granulation

Polyvinylpyrrolidone (PVP) in aqueous solution was used as a binding agent in a fluidized-bed system to agglomerate acetaminophen powder into directly compressible granules. It was found that a minimal amount of 5% w/w PVP in a concentration of 7.5% w/v or less was needed to produce granules with an acceptable flow and the corresponding tablets having enough hardness without capping. There was a strong correlation between the time for 80% dissolved (T₈₀) and the logarithm of granule volume-surface mean diameter. A directly compressible acetaminophen composition to manufacture tablets having a T₈₀ value less than 30 min can be prepared simply by adding an appropriate amount of disintegrant (crospovidone, sodium starch glycolate, or pregelatinized starch) to the agglomerated granules.     

An in vitro model of traumatic neuronal injury: loading rate-dependent changes in acute cytosolic calcium and lactate dehydrogenase release

We developed a new in vitro model of neuronal injury using NT2-N cells to examine the effects of hydrodynamic loading rate on intraneuronal calcium dynamics and lactate dehydrogenase (LDH) release. Our apparatus consisted of a parallel disk viscometer which induced fluid shear stress with well-defined magnitudes and loading rates to cultured cells. We found that the deformation response of the cells was dependent on the severity of the insult, with increased cellular strains generated for higher shear stresses at a constant loading rate. Peak intracellular free calcium concentration correlated with strain, suggesting that mechanical deformation may regulate calcium response. Slowly applied fluid shear stress elicited no response, whereas high loading rates resulted in peak calcium increases 2.9 to 3.6 times baseline values as injury severity was increased. LDH release measured within 5 min after the insult correlated with loading rate. In addition, LDH release continued to increase out to 24 h following high loading rate conditions, demonstrating that the application of fluid shear stress led to prolonged cell damage. The acute response in NT2-N cells subjected to an insult with the CSID is dependent on the loading rate, and these results suggest that initial membrane deformation may trigger subsequent events.     

Interfacial reactions in the squeeze-cast (SAFFIL+C)/SAE 329 Al composite

Interfacial reactions in the squeeze-cast SAE 329 Al alloy reinforced with SAFFIL and carbon fibers were investigated using scanning and transmission electron microscopy and secondary ion mass spectroscopy. The SiO₂ layer added as a binder for the preform of SAFFIL fiber appeared to prevent excessive reaction between the fiber and the molten Al alloy during casting. In the as-cast composite, the reaction between the SiO₂ layer and the Al alloy is considered to produce MgO crystals in the vicinity of SAFFIL fiber. With subsequent heat treatment of the composite to the T6 condition, small crystals of MgO and MgAl₂O₄ were found to form at the surface of SAFFIL fiber as a result of interfacial reaction between the SiO₂ layer and the Al alloy. Even at the T6 condition, significant reactions between the Al alloy and SAFFIL fiber itself were not observed, indicating the effective role of the binder layer in suppressing the degradation of SAFFIL fiber by reaction with the Al alloy.     

Functional topography of cat primary auditory cortex: response latencies

Minimum onset latency (Lmin) of single- and multiple-unit responses were mapped in the primary auditory cortex (AI) of barbiturate-anesthetized cats. Contralateral Lmin for multiple units was non-homogeneously distributed along the dorso-ventral/isofrequency axis of the AI. Responses with shorter latencies were more often located in the central, more sharply tuned region while longer latencies were more frequently encountered in the dorsal and ventral portions of the AI. For single units, a large scatter of Lmin values was found throughout the extent of the AI including cortical depth. The relationship between Lmin and previously reported spectral, intensity and temporal parameters was analyzed and revealed statistically significant correlations between minimum onset latency and the following response properties in some but not all studied animals: sharpness of tuning of a frequency response area 10 dB above threshold, broadband transient response, strongest response level, monotonicity of rate/level functions, dynamic range, and preferred frequency modulation sweep direction. This analysis suggests that Lmin is determined by several independent factors and that the prediction of Lmin based on relationships with other spectral and temporal response properties is inherently weak. The spatial distribution and the functional relationship between these response parameters may provide an important aspect of the time-based cortical representation of specific features in the animal's natural environment.     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators     

Micromachined piezoelectric force sensors based on PZT thin films

A micromachined lead zirconate titanate (PZT) force sensor for scanning force microscope (SFM) is conceptualized by its piezoelectricity. The fabrication procedure is interpreted, and mechanical characteristics of the micromachined PZT force sensors with various lengths are studied in this paper. A compact SFM is constructed by using the piezoelectric PZT sensor. A very clear image is taken by this SFM. The current study of the micromachined PZT force sensor can be considered as a breakthrough of design of SFM as well as a good example of integrated piezoelectric microdevices     

Modified atmosphere packaging of a mixed prepared vegetable salad dish

The aim of this study was to design a modified atmosphere package for a mixed vegetable salad consisting of 75 g of cut carrot, 55 g of cut cucumber, 20 g of sliced garlic and 50 g of whole green pepper. Respiration data of all the components were combined with film permeability data to predict package atmospheres and design optimal packages for experimental testing for improved shelf-life of the produce. The optimal package avoided minimum O₂ and maximum CO₂ tolerance limits, and chilling injury temperatures for any component. A pouch form package made of 27 mm low density polyethylene developed a modified atmosphere of 2.0–2.1% O₂ and 5.5–5.7% CO₂, which was beneficial for all components and provided better quality retention than other test packages.