A mixed-signal RAM decision-feedback equalizer for disk drives

A mixed-signal RAM decision-feedback equalizer (DFE) that operates at 90 Mb/s is described. In the analog domain, the DFE subtracts intersymbol interference caused by the past four outputs. The equalized signal is fed into a nonuniform flash analog-to-digital converter (ADC) to produce the decision output and error signal used to adapt the RAM contents in the digital domain. With a 5 V supply voltage, the power dissipation is 260 mW during steady-state operation. The active area is 4.5 mm² in a 1 μm CMOS process     

Technique for Producing Mullite and Other Mixed-Oxide Systems

Mixed-oxide systems are of interest in a variety of technical ceramic applications. The key in many systems is to achieve a high degree of homogeneity, approaching the molecular level. A technique for producing mixed oxides via direct oxidation of mixtures of organometallic compounds is discussed as a potential route. Preliminary work performed on producing mullite is discussed.     

Neural Network Feedback Control: Work at UTA’s Automation and Robotics Research Institute

This is an outline of research in neural networks for feedback control done since the mid 1990s at the Automation and Robotics Research Institute (ARRI) of The University of Texas at Arlington (UTA). It shows how the developments of Intelligent Control Systems based on neural networks have followed three main generations. This statement provides a short, broad-brush perspective on the development of intelligent neural feedback controllers.     

Contact areas in the thumb carpometacarpal joint

The thumb carpometacarpal joint is a common site of osteoarthritis. It has been hypothesized that peaks of localized stress on the dorsoradial or volar-ulnar regions, or both, of the articular surfaces of the trapezium and metacarpal lead to erosion of cartilage and may be responsible for the progression of the disease. The objective of this study was to determine the contact areas in this joint under the functional position of lateral (key) pinch and in the extremes of range of motion of the joint. These contact areas were assessed relative to the observed sites of cartilage thinning. Eight hands from cadavers of women and five from cadavers of men were tested in vitro with the thumb under a 25 N load in the lateral pinch position, and under small muscle loads (0-5 N) with the thumb in flexion, extension, abduction, adduction, and neutral positions. Contact areas of articular surfaces of the thumb carpometacarpal joint were determined for these positions using a stereophotogrammetric technique. The lateral pinch position produced contact areas predominantly on the central, volar, and volar-ulnar regions of the trapezium and the metacarpal. In three specimens, contact areas were distinctly separated between the dorsoradial and volar-ulnar regions, and in one specimen, from a man, contact occurred exclusively on the dorsoradial region of the trapezium. Using stereophotogrammetry, maps of cartilage thickness also were determined for a subset of nine specimens. The volar-ulnar, ulnar, and dorsoradial regions of the trapezium were the most common sites of thin cartilage, and these may be sites of cartilage wear.(ABSTRACT TRUNCATED AT 250 WORDS)     

CADRE: An Asynchronous Embedded DSP for Mobile Phone Applications

Asynchronous design techniques have a number of compelling features that make them suited for complex system on chip designs. However, it is necessary to develop practical and efficient design techniques to overcome the present shortage of commercial design tools. This paper describes the development of CADRE (Configurable Asynchronous DSP for Reduced Energy), a 750K transistor, high performance, low-power digital signal processor IP block intended for digital mobile phone chipsets. A short time period was available for the project, and so a methodology was developed that allowed high-level simulation of the design at the earliest possible stage within the conventional schematic entry environment and simulation tools used for later circuit-level performance and power consumption assessment. Initial modeling was based on C behavioral models of the various data and control components, with the many asynchronous control circuits required automatically generated from their specifications. This has enabled design options to be explored and unusual features of the design, such as the Register Bank which is designed to exploit data access patterns, are presented along with the power and performance results of the processor as a whole.     

Surface-acoustic-wave frequency-domain limiter

It is shown that, by exploiting the 2-dimensional structure of a SAW substrate to propagate different frequency components over distinct physical paths, the amplitude-limiting process that occurs at high power levels can be made `local? in the frequency domain. One application of such a frequency-domain limiter is to suppress CW interference in spread-spectrum communications.     

Heavy metal content of the hair of children in industrial cities

Nuchal screening has the following advantages: Non invasive. First trimester procedure. Results are obtained quickly. 80-90% detection rate for Down's Syndrome.