Muscular fatigue and maximum endurance time assessment for male and female industrial workers

A single arm pushing experiment was conducted in an electronic factory in Yantai, China to assess muscular fatigue using the theoretical models of muscular strength and maximum endurance time (MET) developed by Ma et al. (2009). Seventy seven workers, including 38 males and 39 females, participated in the study. The muscular strength of pushing was measured after the subject pushed a stick, with a force of 2.5 kgf, for 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 min. Fatigue rate was determined based on a regression approach. In addition to the theoretical model, the MET for such a pushing task was also determined using four empirical models in the literature. The results indicated that females were more resistant to muscular fatigue than males in the pushing task. The results of the muscular strength prediction show that the predictability of the muscular strength model is acceptable. The prediction errors for muscular strength for female subjects were significantly lower than those of the male subjects. The predicted MET using the theoretical model, with a group constant k, was highly correlated with those using the empirical models compared in the current study.     

硼酚醛树脂在涂料中的应用

通过将硼酚醛树脂和环氧树脂进行混用,利用硼酚醛树脂优异的耐酸、碱腐蚀性能以及耐高温性能和环氧树脂可以常温固化成膜的特点,制备常温固化的耐高温防腐蚀涂料。     

纳米TiO_2改性苯丙乳液内墙涂料的研究

采用物理掺和法,在苯丙乳液中加入锐钛型纳米TiO2,制成内墙涂料,进行抑菌试验和甲醛降解实验研究,分析了纳米TiO2的光催化原理和抗菌机理。结果表明,随着TiO2含量增加,甲醛降解能力和抗菌性能增强,当TiO2含量为4%时效果最好。     

如何提高预焙铝电解槽阳极质量

预焙阳极的质量已严重制约铝电解技术的发展，必须予以足够的重视．国外在提高阳极质量方面的有效措施，可以供国内阳极工厂技术改造及科研攻关借鉴．     

PC／PA1010共混物的热行为

利用热失重、微分热失重和显示扫描量热法研究了聚碳酸酯／尼龙１０１０共混物的热行为和解降解过程。结果表明：共混物在６００℃以下分两步降解，降解温度随尼龙１０１０用量增加有下降趋势；共混物的熔点随尼龙１０１０用量增加而升高。     

聚丙烯酸钾与腐植酸复合高吸水性树脂的合成研究

以腐植酸与丙烯酸聚合制备了高吸水性树脂,讨论了交联剂、引发剂以及KOH用量对聚丙烯酸与腐植酸高吸水性树脂吸水率的影响,结果显示在n(MBA)∶n(AA)=0.0005、n(KPS)∶n(AA)=0.0075、n(KOH)∶n(AA)约为0.70、温度为80℃的条件下合成时,其吸水倍率可达到最优值。而且在接近自然条件下(35℃)失水速度慢,保水时间可达100 h以上,重复吸水性能好。运用红外光谱分析了腐植酸与丙烯酸的反应机理。     

氧化硅有序介孔材料MCM-41的微波水热合成及用于组装ZnO纳米粒子

与传统水热合成工艺相比,采用微波水热合成新工艺可以快速合成比表面积大、孔体积和孔径大、孔径分布范围更窄、孔洞呈六方排布的有序介孔材料MCM-41.微波水热合成工艺合成的MCM-41具有合成效率高、成功率高等特点,为此类介孔材料商业化提供了高效的技术手段.采用传统水热工艺合成MCM-41通常需要48～72 h,而采用微波水热合成技术仅需要30 min.采用X射线粉晶衍射(XRD),氮气吸附等技术手段对合成MCM-41材料的物相、比表面积、孔体积、孔径等进行了表征.采用微波水热合成MCM-41的工艺参数为:微波处理的温度120 ℃,时间30 min,微波辐射功率500 W,经过滤、洗涤、干燥、焙烧等处理后,得到的MCM-41具有六方排布的孔系,晶格常数a0=4.4nm,比表面积可达1113 m2/g,平均孔径为2.7 nm,与选用同样配方采用传统水热合成工艺合成的MCM-41的性能相当,却极大提高了合成效率.采用微波水热合成工艺,同样可以合成立方晶系的MCM-48和六方晶系的SBA-15等介孔氧化硅分子筛材料.此外,在微波合成的MCM-41中采用液相工艺成功组装了ZnO纳米粒子,并对组装在MCM-41中的纳米ZnO粒子进行了光催化降解苯酚的实验研究.     

浅析化工企业信息化建设中的问题和对策

加入WTO后,为了提高化工企业的核心竞争力,企业信息化建设已势在必行。本文简要介绍了我国化工企业目前在信息化建设中存在的主要问题以及应采取的对策。     

氯化聚丙烯改性胶粘剂的合成及粘附性能研究

以甲苯为溶剂，过氧化二苯甲酰(BP0)为引发剂，通过自由基聚合，采用甲基丙烯酸羟乙酯(HEMA)和苯乙烯(St)接枝改性氯化聚丙烯(CPP)。研究了不同苯乙烯用量、不同反应温度、不同反应时间、不同引发剂用量对改性氯化聚丙烯胶粘剂粘附性能的影响，得出较佳的工艺条件为反应温度90℃，反应时问2h，原料配比m(CPP)：m(HEMA)：m(St)：m(BPO)=50：0．5：0．6：0．15。     

Improvement of Microwave Loss Tangent and Tunability of Ba0.55Sr0.45TiO3/MgO Composites Using the Heterogeneous Precipitation Method

Ba_0.55Sr_0.45TiO₃/MgO composites were successfully prepared by the heterogeneous precipitation method and their structural, surface morphological, tunable properties, and dielectric properties at microwave frequency were systemically investigated. Compared with the sample prepared by the traditional solid-state method, the sample prepared by the heterogeneous precipitation method exhibits a smaller grain size, more uniform microstructure, higher tunability, and lower microwave loss, and these properties are very beneficial to the development of the microwave tunable devices application. Moreover, the effects of La₂O₃ doping on the dielectric and tunable properties of BST/MgO composites are investigated. The result shows that the La³⁺-doped sample has higher tunability and lower microwave loss than the undoped one.