基于VHDL实现单精度浮点数的加／减法运算

研究了单精度浮点数加／减法的结构及其设计方法，并在Aldec公司的Active—HDL软件环境下，采用VHDL语言进行设计，并进行了仿真验证，计算精度可以达到10^-7。     

尼龙6/改性双马来酰亚胺共混物的制备

将尼龙6与改性双马来酰亚胺熔融共混形成合金以提高其热稳定性能.用转矩流变仪考察了尼龙6/改性双马来酰亚胺共混体系熔融反应过程中的流变行为,用TG-DSC测试了共混物的热性能.结果表明:熔融共混时,2组分间的化学反应进行很快,改性双马来酰亚胺用量增加,共混物的熔融粘度增大,温度或转速升高,平衡转矩降低;改性双马来酰亚胺可明显改善尼龙6的高温热稳定性能,当尼龙6与改性双马来酰亚胺的质量比为20/1时,共混物在236-340℃温度范围内有很好的热稳定性.     

大庆长垣以东古隆起天然气成藏条件的差异性

由长垣以东地区深层天然气分布特征，指出安达—肇州和朝阳沟—肇东古隆起是天然气运移指向和聚集的有利场所。造成安达—肇州古隆起上天然气显示好于朝阳沟—肇东古隆起上天然气显示，前者已获得了大量工业气流，而后者仅见少量气流或显示。但由于天然气在供气条件、储集条件、盖层条件、圈闭条件和运移条件上的差异，造成安达—肇州古隆起本身天然气显示也存在差异，昌德构造、卫星—升平构造和汪家屯构造天然气显示好于模范屯—肇州西构造天然气显示。     

In situ synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology

A novel processing technology was developed to investigate in situ synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology. Thermodynamic analysis was performed to predict possible starting materials and synthesizing conditions of TiC-Al (Ti) nanocomposite powders. A mathematical model was developed to describe temperature profile and velocity distribution in the reactor. The model is applied to optimize feeding rate, input power, and other processing parameters of TiC-Al (Ti) nanocomposite powders by thermal plasma technology, and to predict which materials can be used as starting materials. This paper emphasizes the investigation of the effect of feeding rate, input power, mole ratio, and other process parameters on synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology. The experimental results showed that TiC-Al (Ti) nanocomposite powders can be synthesized in situ by thermal plasma technology, and the average size of TiC-Al (Ti) nanocomposite powders was less than 100 nm.     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

电流控制LPE生长In_（1－x）Ga_xAs_yP_（1－Y）

用电流控制液相外延（ＣＣＬＰＥ）方法首次在（１００）ＩｎＰ衬底上成功地生长出Ｉｎ１－ｘＧａｘＡｓｙＰ１－ｙ（０．３０＜ｘ＜０．４７，０．７０＜ｙ＜０．９６）外延层，并对外延层特性进行了详细研究，提出在ＩｎＰ衬底上生长电外延层的机理，推导出生长动力学的理论模型，该模型与上述实验结果十分吻合。     

基于DSP+CPLD的捷联航姿系统设计与实现

针对捷联航姿系统高精度、小型化、高可靠性的发展需求,文中研究并实现了基于DSP+CPLD导航计算机的光纤航姿参考系统,在导航计算机设计中充分体现了DSP处理器实时解算和CPLD控制信号的双重优点.系统软件可实现加电BIT、磁罗差标定、CRC校验的存储器自检、捷联航姿解算和模糊自适应内阻尼卡尔曼滤波等功能.通过大量的试验验证了硬件的可靠性和算法的有效性.样机实验结果表明基于DSP和CPLD导航计算机的捷联惯性航姿系统性能稳定,满足系统的精度设计要求.     

24m~2烧结机自动化改造方案

介绍烧结机不停产自动化改造的方法,阐述构成工艺过程控制的DCS系统组合以及变频调速技术改造电磁滑差调速成功的选型方法。