Measurements of small-scale fading and path loss for long range RF tags

RF modulated backscatter (RFMB), also known as modulated radar cross section or sigma modulation, is a RF transmission technique useful for short-range, low-data-rate applications, such as nonstop toll collection, electronic shelf tags, freight container identification and chassis identification in automobile manufacturing, that are constrained to have extremely low power requirements. The small-scale fading observed on the backscattered signal has deeper fades than the signal from a traditional one-way link of the same range in the same environment because the fading on the backscattered signal is the product of the fading on the off-board-generated carrier times the fading on the reflected signal. This paper considers the continuous wave (CW) type of RFMB, in which the interrogator transmitter and receiver antennas are different. This two-way link also doubles the path loss exponent of the one-way link. This paper presents the cumulative distribution functions for the measured small-scale fading and the measured path loss for short ranges in an indoor environment at 2.4 GHz over this type of link.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.     

Exchange-correlation errors at harmonic and anharmonic orders: the case of bulk Cu

As an aid towards improving the treatment of exchange and correlation effects in electronic structure calculations, it is desirable to have a clear picture of the errors introduced by currently popular approximate exchange-correlation functionals. We have performed ab initio density functional theory and density functional perturbation theory calculations to investigate the thermal properties of bulk Cu, using both the local density approximation (LDA) and the generalized gradient approximation (GGA). Thermal effects are treated within the quasiharmonic approximation. We find that the LDA and GGA errors for anharmonic quantities are an order of magnitude smaller than for harmonic quantities; we argue that this might be a general feature. We also obtain much closer agreement with experiment than earlier, more approximate calculations.     

Electronic properties of magnetically doped nanotubes

Effect of doping of carbon nanotubes by magnetic transition metal atoms has been considered in this paper. In the case of semiconducting tubes, it was found that the system has zero magnetization, whereas in metallic tubes the valence electrons of the tube screen the magnetization of the dopants: the coupling to the tube is usually antiferromagnetic (except for Cr).     

Securing Mobile Ad hoc Networks — A Motivational Approach

Mobile ad hoc networks rely on the co-operation of devices that route for each other. This immediately presents security problems. Each device's data passes through the not so friendly hands of other devices. Forwarding devices must use their processing power and battery power to route packets for others. When bandwidth is limited they must also use bandwidth that they might want to use for themselves. These are not great issues with the first incarnations of ad hoc networks — military systems or others where all the devices are owned by a single organisation. However, if ad hoc networks are to be generally deployed and become an alternative or adjunct to future cellular systems, then ways to encourage co-operation are required. This revised version was published online in July 2006 with corrections to the Cover Date.