Glass Dielectrics in Extreme High‐Temperature Environment

Thin and flexible glass ribbons can be rolled into a film capacitor structures for power electronic circuits. Glass has excellent electrical properties and is a leading candidate to replace polymer films for high‐temperature applications. The dielectric properties of a low‐alkali aluminoborosilicate glass were characterized up to temperatures of 400°C. Low‐field permittivity values of 6 with dielectric loss below 0.01 were found for temperatures below 300°C. The dielectric breakdown strength exceeded 5 MV/cm for temperature of 400°C and high‐field polarization measurements showed that glass has over 95% energy efficiency at temperatures of 200°C, which is a target temperature for high‐temperature power electronic circuits driven by wide bandgap semiconductor devices.     

Compressive mechanical properties of HTPB propellant at low,intermediate, and high strain rates

Low, intermediate, and high strain rate compression testing (1.7 × 10^?4 to 2500 s^?1) of the hydroxyl‐terminated polybutadiene (HTPB) propellant at room temperature, were performed using a universal testing machine, a hydraulic testing machine, and a split Hopkinson pressure bar (SHPB), respectively. Results show that the stress linearly increases with strain at each condition; the increasing trend of stress at a given strain with the logarithm of strain rate changes from a linear to an exponential form at 1 s^?1. By combining these characteristics, we propose a rate‐dependent constitutive model which is a linearly elastic component as a base model, then multiplied by a rate‐dependent component. Comparison of model with experimental data shows that it can characterize the compressive mechanical properties of HTPB propellant at strain rates from 1.7 × 10^?4 to 2500 s^?1. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43512.     

喷射电沉积技术制备Co-Cr_3C_2复合镀层的工艺优化

为提高微米级硬质陶瓷颗粒在金属基复合镀层的含量,制备性能优异的防护性镀层,采用喷射电沉积的方法在直流电压下制备了Co-Cr_3C_2复合镀层,利用控制变量法探讨了电流密度、固体颗粒用量、镀液流量以及喷枪移动速度等对镀层中颗粒含量及镀层性能的影响,并分析了各因素的影响机理。同时,分别采用能谱仪、显微硬度计和摩擦磨损试验机对复合镀层的成分、硬度和摩擦因数进行分析,最终确定了制备该复合镀层的较优工艺参数。结果显示:喷头移动速度对颗粒复合量的影响最为显著;颗粒复合量越大,复合镀层硬度越高、摩擦因数越低;在较优工艺参数下制备的Co-Cr_3C_2复合镀层的Cr_3C_2颗粒含量高达23.6%。     

热电厂化学中和池废水COD测定方法的实验探究

热电厂化学车间的化学中和池排水具有高氯低COD废水特点,由于氟离子含量高,使得氟离子对COD测定产生强烈干扰,本文通过使用硝酸银对水样中氯离子进行沉淀的前处理方法,消除了COD测定中氯离子的干扰,为该水体中COD的准确测定提供方法依据。     

基于液压惯容器的ISD悬架性能分析与试验

针对机械式悬架存在的惯容器"背隙"的问题,提出一种基于液压惯容器的ISD(inerter-spring-damper,简称ISD)悬架。介绍了液压惯容器的结构及工作原理;建立了液压惯容器ISD悬架的整车模型,在matlab/simulink环境下,进行了压惯容器ISD悬架平顺性仿真;研究了液压惯容器ISD悬架在脉冲输入、随机路面输入作用下的动态性能。在此基础上,进行了液压惯容器ISD悬架台架试验,试验与仿真结果基本吻合。结果表明,与传统被动悬架相比,液压式惯容器ISD悬架可以有效降低车身垂直振动加速度。     

滚珠丝杠式惯容器非线性建模与参数辨识

针对滚珠丝杠式惯容器存在的非线性力学特征,首先,分析了滚珠丝杠式惯容器的工作原理,对惯容器的主要部件进行了非线性力学分析,建立了考虑摩擦、间隙以及丝杠弹性力的惯容器非线性力学模型;然后,在数控液压伺服激振试验台上进行了惯容器的力学性能试验,得到了惯容器在不同惯容系数以及不同激振输入下的力学响应特性;最后,根据试验结果分析了摩擦和间隙对惯容器力学性能的影响,得到了便于参数辨识的惯容器力学模型结构,实现了惯容器输出力仿真与试验结果的分析和对比。结果显示,二者在一个周期内的均方根值误差不超过7%,非线性模型呈现出良好的拟合精度,证明了所述方法的可行性和有效性。