An experimental study of heat transfer characteristics of a pair of longitudinal vortices using color capturing technique

The flow and heat transfer characteristics of a pair of embedded counter-rotating vortices are studied experimentally. In order to control the strength of longitudinal vortices, angle of attack of the vortex generators is varied from ±20° to ±45°, and the spacing between the vortex generators is 4 cm apart. The heat transfer measurements using thermo-chromatic liquid crystal are made to provide the local surface distributions of heat transfer coefficients. The following conclusions are obtained from the present experiment. For the common-flow-down cases, two maximum values in the local heat transfer distributions exist for the three angles of attack. With the common-flow-up cases, only one maximum value exists. The common-flow-down cases show better heat transfer characteristics than the common-flow-up cases.     

Preparation, Characterisation and Catalytic Behaviour of a New TeVMoO Crystalline Phase

TeM_xMo_1.7O mixed oxides (M = V and/or Nb; x = 0-1.7) have been prepared by calcination of the corresponding salts at 600 °C in an atmosphere of N₂. A new crystalline phase, with a Te/V/Mo atomic ratio of 1/0.2-1.5/1.7, has been isolated and characterised by XRD and IR spectroscopy. This phase is observed in the TeVMo or TeVNbMo mixed oxide but not in the TeNbMo mixed oxide. The new crystalline phase shows an XRD pattern similar to Sb₄Mo₁₀O₃₁ and probably corresponds to the M1 phase recently proposed by Aouine et al. (Chem. Commun. 1180, 2001) to be present in the active and selective MoVTeNbO catalysts. Although these catalysts present a very low activity in the propane oxidation, they are active and selective in the oxidation of propene to acrolein and/or acrylic acid. However, the product distribution depends on the catalyst composition. Acrolein or acrylic acid can be selectively obtained from propene on Nb-free or Nb-containing TeVMo catalysts, respectively. The presence of both V and Nb, in addition to Mo and Te, appears to be important in the formation of acrylic acid from propene.     

New Reaction Engineering Concepts for Selective Oxidation Reactions

In order to enhance product yields in selective oxidation reactions, numerous reaction engineering concepts are being studied worldwide. Periodic operation has been investigated for decades, yet its application is limited to a few examples, such as the butane oxidation after DuPont or reverse-flow reactors for VOC removal. The use of microchannel reactors is a younger field, but it has already yielded promising results for process optimization. Catalytic wall reactors have proved to be a helpful tool for kinetic studies. On the laboratory scale, membrane reactors have displayed favorable behavior in selective oxidation. The Na vapor-catalyzed dehydrogenation of methanol to formaldehyde is a final example of an unusual new concept for selective oxidation.     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

Modeling the Kinetics of Growth and the Properties of Nitrided Layers on Steels

Metal Science and Heat Treatment -     

IEEE Richard Harold Kaufmann Award Call for Nominations

This letter further discusses the difference between different definitions of voltage unbalance. Contrary to an earlier letter (see P. Pillay et al., ibid., vol.5, p.50-1, 2001), it is concluded that different definitions may give significantly different results. The two IEEE definitions that were not discussed in the earlier letter give different results and both deviate significantly from the true value (ratio of negative, and positive-sequence voltage) when a zero-sequence component is present.     

0. 6 􀀁m CMOS 雷达天线专用控制芯片设计

雷达系统中天线控制电路完成上位机的初始化和扫描角度控制,要求具有高可靠性和低静态电流,用专用集成电路进行设计具有明显优势.采用Verilog HDL语言描述了系统的逻辑功能,超前进位结构的加/减法器提高了电路的工作速度.利用0.6 μm CMOS工艺完成了天线控制电路的物理实现,芯片面积为1.695 mm×1.631 mm.     

Discussion influence of yield surface curvature on flow localization in dilatant plasticity

The results of finite element calculations for a hollow sphere micromodel are used to examine the underlying assumptions and the specific yield functions in the dilatant plasticity theories of Gurson (1977) and Mear and Hutchinson