A personal computer based system used in electromyography for interpretation and reporting

Programs for rule based electromyography (EMG) interpretation and reporting are described. A number of parameters are obtained during an EMG investigation. The combination of these data leads to a neurophysiological conclusion. Knowledge from the literature, research and experience is the basis for rule development. Rules have been developed for 14 of the most commonly used classifications of an EMG. The syntax is relatively easy and the user may change the rules, add rules or apply the system for other types of data. The results are displayed in a new graphical way. The system presented here is part of an integrated EMG laboratory with administrative routines, distributed databases for storage of results and routines for automatic report generation.     

High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Dimension-structure dependences for the strength of two-phase polycrystalline inorganic materials

Examples are considered of experimental dependences of the strength of two-phase inorganic materials on the shape and size of structural elements, and also dimensional parameters: the mean value of the free path and the mean distance between particles. The structural condition for achieving the maximum strength values for two-phase metallic, cermet, and ceramic materials with a high second phase content is established and substantiated by experiment. An approximate analysis of the dislocation structure of interphase boundaries is performed and their contribution to strengthening of two-phase materials with a dispersed and microlayered structure is demonstrated.Translated from Problemy Prochnosti, No. 1, pp. 3–14, January, 1991.     

Dual-surface integral equations in electromagnetic scattering

A brief review is given of the derivation and application of dual-surface integral equations, which eliminate the spurious resonances from the solution to the original electric-field and magnetic-field integral equations applied to perfectly electrically conducting scatterers. Emphasis is placed on numerical solutions of the dual-surface electric-field integral equation for three-dimensional perfectly electrically conducting scatterers.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Silicon-to-steel bonding using rapid thermal annealing

This paper presents the rapid, low-temperature bonding between silicon and steel using the rapid thermal annealing process. Three different thin-film adhesion layer systems including silver, gold, and nickel were utilized as the intermediate bonding material to assist the eutectic Pb/Sn bonding between silicon and steel. The bonding temperature was set at 220/spl deg/C for 20 s, with a 20-s ramp-up time. Five experiments were conducted to determine the strength of the bond, including static tensile and compressive four-point bend tests, axial extension tests, tensile bending fatigue tests, and corrosion resistance tests. The test results have shown that the gold adhesion layer is the most robust, demonstrating minimal creep during fatigue tests, no delamination during the tensile or compressive four-point bend tests, and acceptable strength during the axial extension tests. Additionally, all adhesion layers have withstood four months of submersion in various high-temperature solutions and lubricants without failure. Simulations of the axial stresses and strains that developed during the four-point bend and axial extension tests were performed and showed that the presence of the silicon die provides a local reinforcement of the bond as observed in the experimental tests.