Microwave Communication to Moving Parts Inside Machines

Cables to moving parts on a linear actuator in production machines, such as pick-and-place machines, are a source of unreliability owing to the possible breaking of a cable. They further reduce the positioning precision of the actuator owing to additional forces. Slotted waveguide systems for rail vehicles based on 2.4 GHz transmission frequency are well known, but transmitters/receivers and waveguides are bulky. The paper reports on the reduction in size of the equipment, adapted to 5.8 GHz using a commercial off-the-shelf RadioLan communication module. Further, the efficient termination of the wave-guide and a new way to reduce standing-wave effects is also discussed.     

Mechanical behavior of 30–50 nm thick aluminum films under uniaxial tension

We present uniaxial tensile test results for 30–50 nm thick freestanding aluminum films. Young’s modulus and ductility were found to decrease monotonically with grain size. Reverse Hall–Petch behavior was observed with no appreciable room temperature creep. Non-linear elasticity with small irreversible deformation was observed for 50 nm thick specimens.     

A comparison between the enhanced mass transfer in boundary and pressure driven oscillatory flow

Mass transport in pulsating flow devices using either moving boundaries or oscillating imposed pressure drops are compared with each other by means of a calculation using a simple model. We conclude that there is no difference between the two configurations as long as one is interested only in the power required to move the fluid for the convective mass transport achieved. However, the boundary driven configuration is more efficient if the power is divided by the total mass transport where both the diffusive and convective parts are taken into account, the boundary driven configuration is more efficient. The amplitude of the piston stroke in the pressure driven configuration and the amplitude in the boundary driven case are assumed to be the same, and the inertia of the moving devices themselves are ignored in this calculation.     

Asymmetric Hydrogenation of Activated Ketones on Platinum: Relevant and Spectator Species

The heterogeneous enantioselective hydrogenation of activated ketones over chirally modified platinum is reviewed with emphasis on identifying the role of the various species observed in this catalytic system. The past years have witnessed a continuous broadening of the scope of this catalytic system including new reactants and modifiers affording over 97% ee. New reaction pathways have been uncovered and the kinetic and mechanistic studies have been faced with a number of complicating factors caused by spectator species and interactions in solution and on the Pt surface. The previously proposed mechanistic models are critically assessed in the light of these new findings.     

Feasibility of fishmeal replacement by shrimp head silage protein hydrolysate in Nile tilapia (Oreochromis niloticus L) diets

This study provides information on the use of shrimp head silage protein hydrolysate (SPH) as an alternative protein source for tilapia feeding. Six diets (28% protein, 12% lipid) were prepared where fishmeal protein was replaced at levels of 0 (control), 10, 15, 20, 25 and 30% with the hydrolysate. The diets were supplied to Nile tilapia fry (338 mg initial weight) stocked in plastic recirculating 20 l tanks (10 animals per tank), with three replicates per treatment. After an 8 week experimental period, fish fed the diets containing 10 and 15% SPH showed significantly better performance in terms of final body weight, weight gain (%), mean daily weight gain (mg day^?1), specific growth ratio and feed conversion ratio than those fed the control diet (fishmeal as protein source) and higher‐SPH diets. It is concluded that shrimp head hydrolysate is a promising alternative protein source for tilapia feeding, improving growth ratio at dietary inclusion levels as high as 15%. In addition, the diets with added shrimp silage protein were well accepted by the fish, which avidly consumed the feed during the experiment. © 2002 Society of Chemical Industry     

Modeling of Calcium Chloride and Pectin Methylesterase Prefreezing Treatments of Strawberries and Jams

ABSTRACT: :
Different calcium chloride (CaCl₂) and pectin methylesterase (PME) prefreezing treatments in a vacuum were used to clarify the most effective prefreezing factors for strawberries and traditional jams. Fractional factorial design and modeling were used. CaCl₂ had the greatest effect on the majority of the 15 studied responses ( p < 0.001). The pretreatment time should be short (about 5 to 10 min), the temperature low (less than 20 °C), the vacuum level high (pressure less than 10 kPa), the CaCl₂ concentration moderate (about 1%) and the dosage of PME comparatively low (about 50 to 100 nkat/g) in order to yield high quality frozen strawberries for jam making.     

Why is software late? An empirical study of reasons for delay insoftware development

A study of the reasons for delay in software development is described. The aim of the study was to gain an insight into the reasons for differences between plans and reality in development activities in order to be able to take actions for improvement. A classification was used to determine the reasons. 160 activities, comprising over 15000 hours of work, have been analyzed. The results and interpretations of the results are presented. Insight into the predominant reasons for delay enabled actions for improvements to be taken in the department concerned. Because the distribution of reasons for delay varied widely from one department to another, it is recommended that every department should gain an insight into its reasons for delay in order to be able to take adequate actions for improvement