Numerische Simulation der Faserbewegung beim Strangpressen kurzfaserverstärkter Glasschmelzen

Numerical Simulation of the Fibre-Motion during the Extrusion of Short-Fibre-Reinforced Glass-Melts Fibre-reinforced materials are characterized by an anisotropic behaviour of the mechanical properties, which is caused by the alignment of the embedded fibres. In the case of short-fibre-compounds this behaviour is strongly influenced by the mechanism of flow during the manufacturing process. Numerical simulation Methods are preferentially used to get informations about the orientation of the reinforced fibres at the end of the molding-process and to improve the properties of the compound. For that, a model is developed, which calculates the motion of the short-fibres in the area of flow, basing on a three-dimensional finite-element-computation. Thereby the interaction between the Particular fibres during the orientation process is considered by using an interaction coefficient. Examplified at the extrusion of short fibre reinforced glass-melts, the fibre orientation is determined at models with different geometries of the pressing tool and variable boundary conditions. This procedure allows to determine the influence of the process-parameters On the expected quality of the composite. The represented simulation-model can also be used for other molding- and extrusion-processes of fibre reinforced materials.     

High speed BiCMOS current mode differential track-and-hold circuit

A new principle for a high speed BiCMOS differential track-and-hold circuit based on current mode processing is presented, and simulation results are given. The main characteristics are an acquisition time of 5.5 ns for 8 bit precision and a small-signal bandwidth of 1 GHz     

SO2 SCRUBBING BY ULTRAFINE CA(OH)2 AEROSOL

The objective of the present study was to generate submicrometer calcium hydroxide aerosols and to investigate the effectiveness of such aerosols in sulfur capture. The effectiveness of SO₂ removal by Ca(OH)₂ aerosol has been investigated in an isothermal reactor. Ca(OH) ₂ aerosol was generated by a novel fluidizer system in which submicrometer-sized powders were entrained in gases. SO₂ was added to this aerosol to a concentration of 2000 ppm. The aerosol-SO₂ mixture was heated to 550°C-750°C in an isothermal tube reactor. The SO₂ removal efficiency, which varied from 20% to 70%, was determined to be a function of the aerosol concentration, reactor temperature and residence time. The fraction of aerosol reacted was not affected strongly by the aerosol concentration. The reaction kinetics were determined from the experimental data using a simple analytical model in which the rate is first order in both SO₂ and calcium hydroxide aerosol concentrations.     

Bridging process and structure through criteria

Scholars in design face two central challenges in design methods inquiry: firstly, to integrate process and solution, and secondly, to examine developmental junctures leading to innovation. With these goals in mind, we maintain that design criteria deserve greater attention and illustrate this position with a study of noted designers' use of criteria. The primary finding was that five criteria functions were considered during the design process. The study also explored potential relationships between designer variables (i.e., professional expertise and personality type) and criteria use.     

Perspective channel-type reactor with enhanced safety

Following the search for new design solutions to develop within the framework of channel trends the reactor with enhanced safety the Research and Development Institute of Power Engineering has developed the design of the multiloop boiling water reactor (MKER). The MKER enhanced safety is attained when involving the inherent safety features, passive safety systems as well as the accident consequences confinement devices. The design realizes several advantages which are typical of the channel-type reactors, namely: the design desintegration simplifying the manufacture, control, equipment delivery and decreasing, versus the pressure vessel reactors, the accident effect if it proceeds in an explosive manner; small operating reactivity margin and fuel burnup increased due to continuous refuelling; fuel cycle flexibility allowing comparatively easily to adopt the reactor to the conjuncture of the country fuel balance; multiloop circuit of the main coolant which reduces the degree and effect of the accidents connected with the equipment and pipings rupture; monitoring of the channels and fuel assemblies leak-tightness.     

Measurement of interfacial area concentration in subcooled liquid-vapour flow

In two-fluid modelling, accurate prediction of the interfacial transport of mass, momentum and energy is required. Experiments were carried out to obtain a database for the development of interfacial transport models, or correlations, for subcooled water-steam flow in vertical conduits. The experimental data of interest included the interfacial area concentration, interfacial condensation heat transfer and bubble relative velocity. This paper focuses on the interfacial area concentration. The interfacial area concentration was obtained by measuring the distributions of bubble volume and surface area as well as the area-averaged void fraction at various axial locations in subcooled water-steam condensing vertical upward flow under low flow rate and low pressure conditions. The bubble size and surface area were determined using high-speed photography and digital image processing techniques. The area-averaged void fraction was measured by a single-beam gamma densitometer. The results were compared with existing correlations, which were developed on the basis of data obtained for air-water adiabatic flows. Poor agreement between the present data and the existing correlations was obtained. Accordingly, new correlations suitable for subcooled liquid-vapour bubbly flow are proposed.     

Synthesis and characterization of tungsten disulphide films grown by pulsed-laser deposition

The synthesis and characterization of tungsten disulphide (WS₂) films grown on 440C stainless steel substrates using the 248 nm line from a KrF excimer laser are reported. Film properties could be adjusted by controlling substrate temperature and by laser or thermal anneals. X-ray photoelectron spectroscopy, glancing angle XRD, Raman spectroscopy and high-resolution scanning electron microscopy were used to evaluate film chemistry, crystallinity and morphology. Films grown at room temperature were amorphous, near stoichiometric, and had a multiplicity of chemical states. Local order and bonding were improved most dramatically through post-deposition laser anneals. Crystallite size could be increased by raising the substrate temperature during deposition and, to a lesser degree, by post-deposition thermal anneals. Local disorder was observed within the larger crystallites compared to those that were laser annealed. Crystallinity was induced in amorphous films by mechanical rubbing at room temperature under conditions where frictional heating was negligible. The degree of control over film properties provided by PLD demonstrates its value for growing/designing tribological coatings.     

Characterization of the flow behaviour of sausage emulsions with a simple tube viscometer

A specially designed tube viscometer was used to measure apparent viscosity during flow of Bologna type sausage emulsions moving through a pipe. Emulsions varied in fat content (from 21.8 to 44.3%) and in moisture/protein ratio (from 3.7 to 5.6), and the effects of added sodium chloride, sodium diphosphate, starch and blood plasma were investigated in a 36% fat, 3.7 moisture/protein emulsion.
The shear stresses determined as a function of shear rate were fitted by a power law. Yield stress of the emulsions was negligible relative to the applied stress. However, inspection of the flow profiles indicated that considerable slip of the sausage emulsion occurred at the pipe wall. Both emulsion flow and slip contribute to overall flow behaviour, so a kind of effective viscosity is determined. Intrinsic rheological properties and wall slip will both be affected by the composition of the sausage emulsion.