Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

Techniques for high-frequency integrated test and measurement

This paper describes techniques for the on-chip measurement of high-frequency and/or high-bandwidth electrical phenomena in ultra large-scale integration environments. The techniques rely on the integration of multiple compact and robust electronic test devices, or cores, at various locations within an integrated circuit. The cores consist primarily of signal generators that approximate the output of a sigma-delta modulator using finite repetitious bit patterns and a small set of highly robust analog components. They are capable of digitizing on-chip signals at gigahertz rates even using low-cost manufacturing processes. Simple communication between the multiple cores enables the migration of many "board-level" type measurements down to the chip level.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

A new mobile robot control approach via fusion of control signals.

This paper proposes an alternative approach to address the problem of coordinating behaviors in mobile robot navigation: fusion of control signals. Such approach is based on a set of two decentralized information filters, which accomplish the data fusion involved. Besides these two fusion engines, control architectures designed according to this approach also embed a set of different controllers that generate reference signals for the robot linear and angular speeds. Such signals are delivered to the two decentralized information filters, which estimate suitable overall reference signals for the robot linear and angular speeds, respectively. Thus, the background for designing such control architectures is provided by the nonlinear systems theory, which makes this approach different from any other yet proposed. This background also allows checking control architectures designed according to the proposed approach for stability. Such analysis is carried out in the paper, and shows that the robot always reaches its final destination, in spite of either obstacles along its path or the environment layout. As an example, a control architecture is designed to guide a mobile robot in an experiment, whose results allows checking the good performance of the control architecture and validating the design approach proposed as well.     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.     

Fracture response of fibre-reinforced materials with macro/microcrack damage using the Boundary Element Technique

The Boundary Element Method (BEM) incorporating the Embedded Cell Approach (ECA) has been used to analyse the effects of constituent material properties, fibre spatial distribution and microcrack damage on the localised behaviour of transversely fractured, unidirectional fibre-reinforced composites. Three specific composites, i.e., glass fibre reinforced polyester, carbon fibre reinforced epoxy and a glass-carbon hybrid, are considered. The geometrical structures examined were perfectly periodic, uniformly spaced fibre arrangements in square and hexagonal embedded cells. In addition, numerical simulations were also conducted using embedded cells containing randomly distributed fibres. The models involve both elastic fibres and matrix, with the interfaces between the different phases being fully bonded. The results indicate that the constituent material properties (two phase composite) and spatial distribution have a significant effect on the localised stress distributions around the primary crack tip. However, the strain energy release rate associated with crack propagation is predominantly influenced by the material composition. The three-phase hybrid composite exhibited an apparent intermediate fracture toughness value, compared to the all-glass and all-carbon models. Furthermore, the strain energy release rate for the macrocrack lowers as it enters a zone of localised damage (microcracking). The presence of microcracks relaxes the stress field, which can result in a significant reduction in the energetics of the primary crack.     

Kinetic Characteristics of Amino Acid Salt Crystallization in Methanol‐Water System

Nucleation and growth mechanisms and kinetics of crystals of an amino acid salt were investigated in a methanol‐water system by measuring and evaluating the induction time as a function of the supersaturation ratio and temperature in batch salting out crystallization experiments. Discrimination between the possible crystallization mechanisms, and estimation of the kinetic parameters were carried out using nonlinear parameter identification. The results concerning the growth mechanism obtained were checked additionally by measuring the induction time as a function of number density of seed crystals.