Start-up and steady-state results of a full-scale UASB reactor treating malting wastewater.

An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater. The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment. After two months of operation the reactor achieved full load with an HRT of 17 h, a COD removal higher than 80% and a biogas production of 300 m3/day (77% average methane content), with an organic loading rate of 3.6 kgCOD/m3.d (0.24 kgCOD/kgVSS.d). A yield coefficient of 0.09 gVSS/gCODrem was found from a mass balance. The fat present in the inoculated sludge (48 mg/gSSV) did not affect the start up performance. Sludge from the inoculum with high content of fat (270 mg/gSSV), was separated by flotation in the first week of operation. The COD removal efficiency was scarcely influenced by the reactor operation temperature (17-25 degrees C).     

Optimised anaerobic treatment of house-sorted biodegradable waste and slaughterhouse waste in a high loaded half technical scale digester.

Anaerobic co-digestion of organic wastes from households, slaughterhouses and meat processing industries was optimised in a half technical scale plant. The plant was operated for 130 days using two different substrates under organic loading rates of 10 and 12 kgCOD.m(-3).d(-1). Since the substrates were rich in fat and protein components (TKN: 12 g.kg(-1) the treatment was challenging. The process was monitored on-line and in the laboratory. It was demonstrated that an intensive and stable co-digestion of partly hydrolysed organic waste and protein rich slaughterhouse waste can be achieved in the balance of inconsistent pH and buffering NH4-N. In the first experimental period the reduction of the substrate COD was almost complete in an overall stable process (COD reduction >82%). In the second period methane productivity increased, but certain intermediate products accumulated constantly. Process design options for a second digestion phase for advanced degradation were investigated. Potential causes for slow and reduced propionic and valeric acid degradation were assessed. Recommendations for full-scale process implementation can be made from the experimental results reported. The highly loaded and stable codigestion of these substrates may be a good technical and economic treatment alternative.     

Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Geometric derivation of expectation-maximization and generalized successive interference cancellation algorithms with applications to CDMA channel estimation

The expectation-maximization (EM) algorithm is well established as a computationally efficient method for separable signal parameter estimation. Here, a new geometric derivation and interpretation of the EM algorithm is given that facilitates the understanding of EM convergence properties. Geometric considerations lead to an alternative separable signal parameter estimator based on successive cancellation. The new generalized successive interference cancellation (GSIC) algorithm is then applied to multiuser delay and channel estimation for code-division multiple access (CDMA) radiolocation and communication. The radiolocation application uses a handshaking protocol in which multiple reference nodes transmit acknowledge (ACK) CDMA packets to a master node, which then computes round-trip travel times (RTTs). Simulation results comparing EM and GSIC are presented for the CDMA channel-estimation problem.     

Steady-state operation of a high-voltage multiresonant converter in a high-temperature environment

Often scientific instruments on exploratory satellites are used to collect cosmic particles. These instruments, such as the Faraday cup, require a high-voltage regulated power source. On the proposed solar probe satellite there will be instruments which will collect cosmic particles close to the sun. Naturally temperature effects on the voltage regulator are a concern. Specifically power dissipation within the regulator must stay within stringent guidelines. The high-voltage regulator circuit is a resonant flyback topology with a dissipative series switch whose on resistance controls the output voltage level. The extreme temperatures in space will change the inductance of the flyback transformer which will affect the output voltage. State space analysis techniques are used to determine how the value of the transformer inductance and capacitance in the flyback converter affects the output voltage and consequently the power dissipated by the transformer and the switch. The accuracy of the analysis is verified by comparing results with those obtained from an experimental circuit. The results can then be used to help the designer chose nominal capacitance and inductance values that will work over the temperature range of interest.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.