Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Climatic solar roof: an ecological alternative to heat dissipation in buildings

A new system based on the harnessing of solar and wind power is presented for heat dissipation in air conditioning facilities. The innovation offered by the new system is the integration of two well-known subsystems: a cooling tower and a solar chimney which increases the air flow without the use of electric power. The system is described and presented together with a model for its study. The field data acquired from the prototype built in southern Spain establishes the actual potential of the system, which provides a new approach to a sustainable technological development.     

Parametric inference for step-stress models

Applications of the additive accumulation of damages (AAD) or the accelerated failure time (AFT) and the proportional hazards (PH) models in accelerated life testing with step-stresses are discussed. A new model including AAD and PH models is proposed. It is more reasonable than the PH model and wider then the AAD model. Constructing the maximum likelihood function is discussed     

Analysis of burn-in time using the general law of reliability

Empirical lifetime distributions sometimes have a bathtub-shaped failure rate. This paper deals with some models having a bathtub-shaped failure rate. The root-mean-square criterion is proposed for selection of the best model. Besides two criteria of optimum burn-in time are proposed. The comparison of some models with the general law of reliability is given to determine a burn-in time in a number of examples.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

A multi-agent decision support system for stock trading

A distributed problem solving system can be characterized as a group of individual cooperating agents running to solve common problems. As dynamic application domains continue to grow in scale and complexity, it becomes more difficult to control the purposeful behavior of agents, especially when unexpected events may occur. This article presents an information and knowledge exchange framework to support distributed problem solving. From the application viewpoint the article concentrates on the stock trading domain; however, many presented solutions can be extended to other dynamic domains. It addresses two important issues: how individual agents should be interconnected so that their resources are efficiently used and their goals accomplished effectively; and how information and knowledge transfer should take place among the agents to allow them to respond successfully to user requests and unexpected external situations. The article introduces an architecture, the MASST system architecture, which supports dynamic information and knowledge exchange among the cooperating agents. The architecture uses a dynamic blackboard as an interagent communication paradigm to facilitate factual data, business rule, and command exchange between cooperating MASST agents. The critical components of the MASST architecture have been implemented and tested in the stock trading domain, and have proven to be a viable solution for distributed problem solving based on cooperating agents     

New bounds for the Marcum Q-function

New bounds are proposed for the Marcum Q-function, which is defined by an integral expression where the 0th-order modified Bessel function appears. The proposed bounds are derived by suitable approximations of the 0th-order modified Bessel function in the integration region of the Marcum Q-function. They prove to be very tight and outperform bounds previously proposed in the literature. In particular, the proposed bounds are noticeably good for large values of the parameters of the Marcum Q-function, where previously introduced bounds fail and where exact computation of the function becomes critical due to numerical problems     

Universal Rendering Sequences for Transparent Vertex Caching of Progressive Meshes

We present methods to generate rendering sequences for triangle meshes which preserve mesh locality as much as possible. This is useful for maximizing vertex reuse when rendering the mesh using a FIFO vertex buffer, such as those available in modern 3D graphics hardware. The sequences are universal in the sense that they perform well for all sizes of vertex buffers, and generalize to progressive meshes. This has been verified experimentally.     

A new hybrid active power filter (APF) topology

In this paper, a new hybrid active power filter topology is presented. A higher-voltage, low-switching frequency insulated gate bipolar transistor (IGBT) inverter and a lower-voltage high-switching frequency metal oxide semiconductor field effect transistor (MOSFET) inverter are used in combination to achieve harmonic current compensation. The function of the IGBT inverter is to support utility fundamental voltage and to compensate for the fundamental reactive power. The MOSFET inverter fulfills the function of harmonic current compensation. To further reduce cost and to simplify control, the IGBT and MOSFET inverters share the same DC-link via a split capacitor bank. With this approach harmonics can be cancelled over a wide frequency range. Compared to the conventional APF topology, the proposed approach employs lower dc-link voltage and generates less noise. Simulation and experimental results show that the proposed active power filter topology is capable of compensating for the load harmonics