A Gravitational Search Algorithm Based Static VAR Compensator Switching Function Optimization Technique for Minimum Harmonic Injection

Switching function optimization for minimum source harmonic injection for a static VAR compensator is presented. The static VAR compensator is configured with a fixed capacitor and insulated-gate bipolar transistor controlled reactor. The switching function is optimized for minimum source harmonic injection considering the desired fundamental voltage across load terminals. A gravitational search algorithm is employed for this purpose. It is observed that the proposed switching scheme with two different switching angles per half-cycle provides lower source harmonic injection compared to conventional switching, hence improving the source current harmonics. The switching angles are computed off-line using the gravitational search algorithm for varying modulation indices considering the minimum total harmonic distortion of the reactor voltage. The switching angles are stored in a processor as a function of the modulation index for on-line application using a piecewise mixed model approximation technique for low memory usage. It is observed that the proposed switching improves the source current total harmonic distortion on an average of 4 to 5% over most of the operating range compared to conventional switching without optimization. Various simulation and experimental results are presented on different loads to validate the proposed concept.     

Influence of Substrate Temperature on the Properties of Cobalt Oxide Thin Films Prepared by Nebulizer Spray Pyrolysis (NSP) Technique

Cobalt oxide thin films are prepared by the nebulizer spray pyrolysis technique using cobalt chloride as the precursor material. The structural, optical, morphological and electrical properties are investigated as a function of substrate temperature (300–450 °C). The X-ray diffraction (XRD) analysis reveals that all the films are polycrystalline in nature, having cubic structure with preferential orientation along the (111) plane. The optical spectra show that the films are transparent (68 %) in the IR region. The optical band gap values are calculated for different substrate temperature. Photoluminescence (PL) spectra of the films indicate the presence of indigo, blue and green emission peaks with an ultraviolet emission peak centered around 368nm. SEM images reveals small sphere-like structures for the prepared Co3O4 films. The maximum conductivity obtained is 1.48 x 10?3 S/cm at 350 °C. The activation energy varies between 0.039 and 0.138 eV for the substrate temperature variation from 300-450 Q°C.     

Heterogeneous Catalytic Polymerization of Ethylene in Microtubular Reactor Systems

The feasibility of using a microtubular reactor for heterogeneous polymerization of ethylene was investigated experimentally. Chemically inert polymer tubing of 800–2300 μm in inner diameter was fabricated and used as a polymerization reactor. Nonporous silica nanoparticles with a diameter of 400 nm were synthesized and used as support for the high‐activity rac‐ethylene(indenyl)₂ZrCl₂ catalyst with methylaluminoxane as cocatalyst and toluene as diluent. Large‐diameter microtubular reactors were also successfully used to conduct heterogeneous polymerization of ethylene in continuous reaction operations. High initial catalyst activity was obtained and the overall polymerization activity per volume or reactor length was quite high. No particle fragmentation occurred and the polymer particles were covered with small subgrains or nanofibrils with a diameter of 30 nm.     

Conformation Analysis of GalNAc‐Appended Sugar Amino Acid Foldamers as Glycopeptide Mimics

Sugar amino acid (SAA)‐based foldamers with well‐defined secondary structures were appended with N‐acetylgalactosamine (GalNAc) sugars to access sequence‐defined, multidentate glycoconjugates with full control over number, spacing and position. Conformation analysis of these glycopeptides by extensive NMR spectroscopic studies revealed that the appended GalNAc units had a profound influence on the native conformational behaviour of the SAA foldamers. Whereas the 2,5‐cis glycoconjugate showed a helical structure in water, comprising of two consecutive 16‐membered hydrogen bonds, its 2,5‐trans congener displayed an unprecedented 16/10‐mixed turn structure not seen before in any glycopeptide foldamer.     

Efficient Host-Guest Complexation of a Bisporphyrin Host with Electron Deficient Guests: Synthesis,Structure, and Photoinduced Electron Transfer

The encapsulation of 1,8-naphthalic anhydride (NAN), 9-dicyanomethylenefluorene (9-DCF), acenaphthenequinone (ANQ), and 4-chloro-7-nitrobenzofurazan (NBD-Cl) by diethylpyrrole-bridged bisporphyrin (H₄DEP) and its dizinc(II) analogue (Zn₂DEP) are employed to investigate the structural and spectroscopic changes within the bisporphyrin cavity upon substrate binding. Synthesis and X-ray structures of all four encapsulated host-guest complexes (H₄DEP⋅NAN, H₄DEP⋅9-DCF, Zn₂DEP⋅ANQ, and Zn₂DEP⋅NBD-Cl) are reported here. The binding constant calculations show strong 1 : 1 binding between the hosts (H₄DEP and Zn₂DEP) and the guests (NAN/9-DCF/ANQ/NBD-Cl). ¹H-NMR spectra also support the retention of the host-guest assemblies in solution. Negative and positive shifts of the reduction and oxidation potentials, respectively, indicate that it is difficult to reduce/oxidize the encapsulated complexes. The emission intensities of the bisporphyrins (H₄DEP and Zn₂DEP) are substantially quenched in all the complexes, owing to photoinduced electron transfer from the excited state of the bisporphyrins to guest molecules. All the experimental evidence is further substantiated by DFT calculations. Such an efficient electron transfer is only possible when the donor and the acceptor moieties are in close propinquity to each other, which eventually lowers the reorganization energy.     

An analytical approach to dynamic crosstalk in coupled interconnects

This paper deals with waveform analysis, crosstalk peak and delay estimation of CMOS gate driven capacitively and inductively coupled interconnects. Simultaneously switching inputs for the coupled interconnects are considered. A transmission line-based coupled model of interconnect is used for analysis. Alpha-power Law model of MOS transistor is used to represent the transistors in CMOS driver. Peaks and delays at far-end of victim line are estimated for conditions when the inputs to the two coupled interconnects are switching in-phase and out-of-phase. The comparison of analytically obtained results with SPICE simulations show that the proposed model captures noise peak and their timing; 90% propagation delay; transition time delay and waveform shape with good accuracy, such as not more than 5% error in crosstalk peak estimation.     

Gradient histogram: Thresholding in a region of interest for edge detection

Selecting a threshold from the gradient histogram, a histogram of gradient magnitudes, of an image plays a crucial role in a gradient based edge detection system. This paper presents a methodology to determine the threshold from a gradient histogram generated using any kind of linear gradient operator on an image. We consider the image as a random process with dependent samples, model the gradient histogram using theories of random process and random input to a system, and determine a region of interest in the gradient histogram using certain properties of a probability density function. Standard histogram thresholding techniques are then used within the region of interest to get the threshold value. To obtain the edges, this threshold value is then used as the upper threshold of the hysteresis thresholding technique that follows the non-maximum suppression operation applied on the gradient magnitude image. The proposed methodology of determining a threshold in a gradient histogram is deduced through rigorous analysis and hence it helps in achieving consistently appreciable edge detection performance. Experimental results using different real-life and benchmark images are shown to demonstrate the effectiveness of the proposed technique.     

Performance evaluation of TiAlCrYN nanocomposite coatings deposited using four-cathode reactive unbalanced pulsed direct current magnetron sputtering system

Approximately 1.5-2.5 μm thick nanocomposite coatings of TiAlCrYN were deposited using a four-cathode reactive unbalanced pulsed direct current magnetron sputtering system from the sputtering of Ti, Al, Cr, and Y targets in Ar + N₂ plasma. The TiAlCrYN nanocomposite coatings were deposited on various substrates such as high speed steel (HSS) drill bits, mild steel and silicon. TiAlCrYN coatings with almost similar mechanical properties but with different Ti, Al, Cr and Y contents were prepared to study their thermal stability and machining performance. The structural and mechanical properties of the coatings were characterized using X-ray diffraction and nanoindentation technique, respectively. The elemental composition, bonding structure, surface morphology and cross-sectional data were studied using energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy and field-emission scanning electron microscopy, respectively. Nanoscratch tests were performed to determine the adhesive strength of the coatings. The corrosion behavior of TiAlCrYN nanocomposite coatings on mild steel substrate was studied using potentiodynamic polarization in a 3.5% NaCl solution. Micro-Raman spectroscopy was used to characterize the structural changes as a result of heating of the nanocomposite coatings in air (600-1000 °C). TiAlCrYN coatings prepared at 17 at.% Ti, 13 at.% Al, 21 at.% Cr and 1 at.% Y exhibited thermal stability as high as 900 °C in air (denoted as Sample 3). For the performance evaluation, the TiAlCrYN coated HSS drill bits were tested under accelerated machining conditions. With a drill speed of 800 rpm and a feed rate of 0.08 mm/rev the TiAlCrYN coated HSS drill bits (Sample 3) averaged 657 holes, while drilling a 12 mm thick 304 stainless steel plate under dry conditions, before failure. Whereas, the uncoated drill bits failed after drilling 50 holes under the same machining conditions. Results indicated that for the HSS drill bits coated with TiAlCrYN, the tool life increased by a factor of more than 12.     

Effects of rolling and hot pressing on mechanical properties of boron carbide-based ceramics

A study of hot pressed B₄C-based laminates, after rolling and without rolling, has been performed to elucidate the existence of fracture resistance/crack length anisotropy induced by this processing technique. While the crack lengths/fracture resistance was affected significantly by the presence of the residual stresses in B₄C/B₄C–ZrB₂ laminates, no differences in Vickers crack lengths were observed in B₄C/B₄C laminates prepared by rolling and hot pressing, as compared to the crack lengths seen in pure B₄C ceramics prepared by hot pressing without rolling. X-ray diffraction analysis confirmed that no texture has been formed during the rolling and hot pressing of B₄C ceramics.     

Dishing and nitride erosion of STI-CMP for different integration schemes

In this paper, we investigate the effects of integration schemes on the STI-CMP performance of two polishers, as well as the influence of consumables and process parameters. The experiment was based on both the blanket-oxide wafers and the patterned wafers processed using 0.18 μm technology. The polishing capability was evaluated, based on the results collected using metrology tools such as Opti-probe, Tencor profiler; atomic force microscope (AFM), and x-ray-scanning electron microscopy (X-SEM) analysis.