Antimicrobial residues survey by LC-MS in food-producing animals in Lebanon

ABSTRACT

The treatment of animals with antimicrobial products may lead to the contamination of edible tissues by their residues, which may represent a risk to human health. Therefore, this study aimed to determine the level of antimicrobial residues in food-producing animals (chicken, beef, and milk) in Lebanon. A total of 310 samples were collected and analysed using an LC-MS/MS for the determination of 48 compounds belonging to different families in order to map their compliance according to the European Commission decision 2002/657/EC. Results show that 60% of the analysed samples were not contaminated by any residue, while 12% presented a concentration higher than the MRLs for tetracyclines, sulphonamides, quinolones, and macrolides. Results revealed that chicken were the most contaminated by antimicrobial residues, when compared to beef and milk. The obtained results demonstrate the uncontrolled use of antimicrobials in some Lebanese farms and claim for better management of livestock.     

Duodenal erosions and ulcers in patients with pancreatobiliary obstruction

The authors compared in a controlled clinical study two groups of patients after a first renal transplantation treated by triple drug immunosuppressive therapy. In a group of 31 patients the triple combination comprised Sandimmune Neoral. In the control group there were 30 patients who received Sandimmune. No differences were found between the two groups as regards the effectiveness of this treatment and the authors did not confirm a lower incidence of rejections described in patients treated with Sandimmune Neoral. They confirmed, however, a lower interindividual variability of Cy-A levels assessed specifically in patients treated with Sandimmune Neoral.     

Reliability and scale effect in toughness of concrete structures

In the present work, the distribution of the random toughness characteristics (i.e. critical energy release rate, G_1c) has been evaluated on the basis of experimental observations. Fracture test results from three groups of geometrically similar concrete specimens of size (width×total depth×thickness), 420×420×50–1680×1680×200 mm³, made with different maximum aggregate size of 9.5, 19, 38, and 76 mm were analyzed using a recently proposed distribution of extremes. In applications of probability, it is important to use an appropriate distribution type and adequate techniques for estimating the parameters of distribution. In this study, a new type distribution of minima is employed for probability computations. It was noticed that the entropy of distribution increases with the crack length, i.e. the uncertainty of toughness, G_1c, value increases with crack length. A non-linear reduction of the maximum allowable splitting force with the defect size, a, was noticed. For large specimens, the maximum allowable splitting load is more sensitive to the required reliability level than that for small specimens. Reliability increases with aggregate size when all other conditions were constant.     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Impact Fracture of Thermally Tempered Glass Helicopter Windshields

In-service fracture of helicopter windshields was studied. Simulated catastrophic fracture tests were conducted by firing alumina and steel spheres onto stationary tempered and as-received glass panels. The results were studied by Hertzian analysis and modified Auerbach's relations. Thermally tempered glass shows much higher impact resistance than that estimated from superposition of residual stresses. Subcritical impact sites exhibit slow crack growth in tempered plates, eventually leading to fracture of the entire plate.     

Study of hot air generator with quasi-uniform temperature using concentrated solar radiation: Influence of the shape parameters

The non-uniformity of the air temperatures and the slow flow rate at the plane collector exit constitute the main cause of the limitations of the solar drying systems. In order to obtain an uniform and a variable flow rate for different uses, a hot air generator using concentrated solar radiation is proposed. To improve the thermal efficiency of the generator, a study of the influence of different shape parameters is realized. The generator is simulated in the laboratory while investigating the flow induced by a circular disc heated uniformly by Joule effect at constant temperature. This disc is placed at the entrance of an open ended vertical cylinder of a larger diameter. Thermal radiation emitted by the hot disc heats the cylinder wall. The heating of the fluid at the cylinder-inlet generates a thermosiphon flow around the one created by the hot disc. The comparison of the velocity and the temperature profiles of the resulting flow permits to determine the influence of the cylinder height, the vertical source-cylinder spacing and the radius ratio, on the resulting flow at the system exit. Thus, a judicious choice of the shape parameters entails an improvement of the flow rate as well as the thermal flux absorbed by the air and a good homogenization of the air temperature at the generator exit.     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

优化移动多媒体传输链的功耗

消费者对于移动多媒体的需求是毫无疑问的，满足这些需求的技术已经开发成功，对于设计人员而言，剩下的问题就是如何利用这些技术，并将成功的产品带入市场。本文将讨论如何减省移动多媒体设备内关键元件的功耗，此外也会对现今移动多媒体设备设计人员所面对的工程挑战作出概括的分析，并就目前及新涌现的硅技术，提出可克服这些工程挑战的解决方案。