Manufacture of Syntactic Foams: Pre-Mold Processing

Manufacturing processes for syntactic foams made of hollow microspheres and starch were studied. Various manufacturing parameters in relation to the “buoyancy method” were identified and inter-related. An equation based on unit-cell models with the minimum inter-microsphere distance concept for a relation between volume expansion rate of bulk microspheres in aqueous starch and microsphere size was derived and successfully used to predict experimental data. It was demonstrated that the inter-microsphere distance can be calculated numerically for microspheres with known statistical data. The equation relating between volume expansion rate and microsphere size was further extended to accommodate a relation between inter-microsphere distance and microsphere size but with limited accuracy for binders of low starch content. An alternative empirical linear equation for the relation between inter-microsphere distance and microsphere size is proposed for wider applications. A simple method for estimation of syntactic foam density prior to completion of manufacture is suggested. Shrinkage after molding of syntactic foam is discussed in relation with different stages such as slurry, dough and solid. A two-step manufacturing process involving molding and then forming is suggested for syntactic foam dimensional control.     

The sulphidation of alloys used in a fluidized bed combustor

The results of an investigation of the sulphidation behaviour of lncoloy BOOH and AISI 310 stainless steel in coal combustion conditions at temperatures between 650°C and 900°C are presented. Laboratory tests were carried out in controlled environments in the presence of solids representative of fluidized bed combustor operation. The morphology and composition of scale formed during sulphidation was examined and compared with that from tube samples removed from test rigs operated by the National Coal Board. The results have shown that at 900°C a gas mixture corresponding to the equilibrium conditions close to the coexistence point for CaS0₄, CaO and CaS on the phase stability diagram is sufficient to induce sulphidation. However, at lower temperatures an interaction between the deposit and the protective oxide is necessary and in some cases the presence of typical contaminants found in coals is an added requirement. The morphology of the corrosion products found in practice can be reproduced under controlled conditions in laboratory tests. The results are interpreted in terms of likely mechanisms of the processes involved.     

Integration of GIS and multicriteria decision analysis for urban aquaculture development in Bangladesh

Site selection is a key factor in any aquaculture operation, affecting both success and sustainability as well as solving land or water use conflicts. This study was conducted to identify suitable sites for carp farming development in urban water bodies (UWBs) of Chittagong, Bangladesh using Geographical Information Systems (GIS) based MultiCriteria Evaluation (MCE) of water, soil and infrastructure database. ASTER imagery and 14 thematic layers were analyzed with ENVI and GIS capabilities, and developed a series of GIS models to identify and prioritize the appropriate UWBs for carp farming. The study identified 487 UWBs occupying 362 ha and revealed 280 ha (77%) is the most suitable, 36 ha (10%) is moderately suitable and 46 ha (13%) is not suitable which was consistent with field verification. The results are encouraging for extension of carp culture and diversify the economic activities of the urban dwellers.     

Improved calculation of Si sputter yield via first principles derived interatomic potential

Silicon sputter yield under medium energy Ar+ ion bombardment is calculated via molecular dynamics, using a highly accurate interatomic potential for Ar-Si interactions derived from first-principles calculations. Unlike the widely used universal repulsive potentials such as the Moliere or ZBL parameterizations, this new potential, referred to as DFT-ArSi, is developed via localized basis density functional theory. Sputter yields for Si obtained with the DFT-ArSi potential at 500 eV and 1 keV incident energies are found to be within 6% and 2% of experimental results, respectively, while errors using existing potentials are typically on the order of 11%. The DFT-ArSi potential differs from existing empirical potentials in the ∼1 Å interatomic separation range which is shown to be the most important range for modeling low-to-medium energy ion bombardment.     

Aloe vera gel: a new thickening agent for pigment printing

An attempt was made to print cotton fabric with pigments using a new thickening agent based on Aloe vera gel in combination with sodium alginate. The results were compared with the standard conventional printing recipe containing synthetic thickener, and a favourable effect of Aloe vera introduction was achieved. The results show that the properties of the printed fabric (sharpness, colour yield, overall fastness properties, softness, and water vapour transmission) are dependent on the percentage of Aloe vera gel in the thickener combination, the concentration of printing auxiliaries, and the curing conditions. Optimal printing properties were achieved by using a printing paste containing 80% Aloe vera/20% sodium alginate (700 g kg^?1), pigment (50 g kg^?1), binder (145 g kg^?1), fixer (10 g kg^?1), and ammonium sulfate (5 g kg^?1), followed by drying at 85 °C for 5 min and curing at 150 °C for 3 min. The sample printed with the new recipe showed superior rubbing fastness and handle properties, with a slightly lower colour yield, when compared with the sample printed with synthetic thickener. Finally, economic issues arising from synthetic thickener substitution are highlighted.     

Effect of different titania phases on the hydrogen gas sensing features of polyaniline/TiO2 nanocomposite

This paper presents a resistance-based hydrogen gas sensor using polyaniline (emeraldine)/TiO₂ nanocomposite (PT–NC) thin film. It is demonstrated that different gas sensing features can arise when various TiO₂ phases (anatase and rutile) are applied. The different wt% of TiO₂ phases were dispersed into an acidic solution of aniline monomers and PT–NCs were synthesized by an in-situ self-assembly chemical oxidative polymerization method of aniline. PT–NCs deposited on an epoxy glass substrate having Cu-interdigited electrodes for hydrogen gas sensing at air pressure and room temperature. Our results show that the better sensitivity of the sensor strongly depends on the sensor surface morphology and its components. Furthermore, hydrogen gas sensing mechanism of the sensor based contact areas between Pani chains and TiO₂ grains was studied.     

Effect of tanniniferous Terminalia chebula extract on rumen biohydrogenation, ∆(9)-desaturase activity, CLA content and fatty acid composition in longissimus dorsi muscle of kids

Conjugated linoleic acid, a fatty acid found in milk fat and ruminant meat is one of the functional food components. Modifying fatty acid composition so as to increase CLA and other beneficial PUFA/MUFA level and reducing SFA levels might be a key to enhance the neutraceutical and therapeutic value of ruminant-derived food products. In the present experiment, the effect of supplementation of polyphenol rich Terminalia chebula plant extract at different concentrations (1.06 g/kg and 3.18 g/kg of body weight in T1 and T2 groups, respectively) was investigated on fatty acid composition of rumen fluid, plasma, intramuscular fat and Δ9-desaturase activity in longissimus dorsi muscle of crossbred kids. Total MUFA and PUFA content in muscle were enhanced by 25 and 35%, respectively, whereas SFA was reduced by 20% thereby improving the desaturation index. Δ9-desaturase activity also increased by 47% resulting in an enhancement of total CLA content (58.73%) in muscle.     

Synthesis,Characterization and Catalytic Activities of Palladium(II) Nitroaryl Complexes

Two palladium(II) nitroaryl complexes trans-[bromo(p-nitrophenyl)bis(triphenylphosphine)palladium(II)] 1 and trans-[bromo(2,4-dinitrophenyl)bis(triphenylphosphine)palladium(II)] 2 have been synthesized. The complexes were characterized by FTIR and NMR (¹H, ¹³C and ³¹P) spectroscopy and elemental analysis. The molecular structure of complex 2, as confirmed by X-ray crystallography, reveals that the Pd atom and its neighboring groups (two PPh₃, Br and phenylene group) lie in a slightly distorted square plane. In the UV–Vis spectra of the complexes 1 and 2, the palladium to aryl charge transfer bands were observed. The emission peaks from the singlet excited states (S₁ → S₀) were observed in the photoluminescence spectra of the complexes. The thermal stability of the complexes has been studied by thermal gravimetric analysis (TGA). TGA data showed that both complexes are thermally stable up to 200 °C, and complex 1 is more stable than 2. The catalytic efficiency of the new palladium(II) complexes was studied as demonstrated using the Sonogashira coupling reactions with good yields. The experimental results suggest that the Sonogashira coupling reactions can be performed at moderate temperature (50 °C) using these new palladium(II) complexes as catalysts.