Manufacturing processes for syntactic foams made of hollow microspheres and starch were studied. Various manufacturing parameters in relation to the “buoyancy method” were identified and inter-related. An equation based on unit-cell models with the minimum inter-microsphere distance concept for a relation between volume expansion rate of bulk microspheres in aqueous starch and microsphere size was derived and successfully used to predict experimental data. It was demonstrated that the inter-microsphere distance can be calculated numerically for microspheres with known statistical data. The equation relating between volume expansion rate and microsphere size was further extended to accommodate a relation between inter-microsphere distance and microsphere size but with limited accuracy for binders of low starch content. An alternative empirical linear equation for the relation between inter-microsphere distance and microsphere size is proposed for wider applications. A simple method for estimation of syntactic foam density prior to completion of manufacture is suggested. Shrinkage after molding of syntactic foam is discussed in relation with different stages such as slurry, dough and solid. A two-step manufacturing process involving molding and then forming is suggested for syntactic foam dimensional control. 相似文献
Biofuel production via microalgae is a promising and sustainable alternative to replace the typical fossil fuel that is the main contributor to the global warming. However, for a cost‐effective biofuel production, further advanced research is still needed for large‐scale operation. This article is a tutorial review on conversion processes of microalgae into biofuel, with emphasis on biochemical conversion. The following topics are discussed: (i) microalgae biomass and its composition, (ii) thermochemical conversion, (iii) chemical conversion, and (iv) biochemical conversion. In addition, various aspects of anaerobic digestion, digester designs, and effects of operating conditions on the production of methane, bioethanol, and biohydrogen are discussed. The general kinetics of biomass conversion into biofuel is presented. This study suggests, if that biomass contains less than 50 % moisture, then it is recommended to use the direct combustion method; otherwise, biochemical conversion is the most suitable process to biofuel production. 相似文献
This study reports the influences of gamma irradiation (GI) in the range of 20–100 kGy on CuO thin films via thermal spray pyrolysis technique on the glass substrates. The results demonstrate significant influences of GI on the crystallographic, microstructural and optical characteristics of CuO thin films. The obtained XRD results showed that the crystallinity of the films deteriorates by gradually decreasing crystallite size (from 59.13 to 46 nm) as applied gamma doses increases. However, the basic monoclinic crystal structure remains same. The dislocation density and lattice strain increased with the rise of GI absorbed dose due to the creation of defects. The values of number of crystallites per unit surface area increased as dose increased indicating the abundance of crystallization of nano CuO thin films. A UV–Vis–NIR spectrophotometer was utilized to determine the optical properties and obtained results indicated that the optical energy band gap (OBG) energies reduced from 2.00 to 1.72 eV as the doses increased from 0 to 100 kGy. No distinctions of the monoclinic phase of virgin CuO thin film have been perceived under applied absorbed doses, notwithstanding the slight deterioration of the crystallinity and narrowing the OBG. 相似文献
Iranian Polymer Journal - Hydrogels were produced from mixtures of polyvinyl alcohol (PVA), polyvinyl pyrrolidone (PVP), and acrylic acid (AAc) using γ-radiation at doses of 3, 7, and... 相似文献
In reservoir system operation, optimization is very much essential and the compatibility of different optimization techniques is essential to be checked by some performance checking indices. In this study, various types of performance-measuring index are used and compared to provide a complete knowledge on adopting different approaches. Here, the considered performance-measuring indicators will check the operation policy in terms of three different scenarios—how the method is efficient in achieving best results (reliability); how vulnerable the method is for different critical situation (vulnerability); and how capable it is to handle a failure of the model (resiliency). Therefore, the study proposed the artificial bee colony (ABC) optimization technique to develop an optimal water release policy for the well-known Aswan High Dam, Egypt. Particle swarm optimization, genetic algorithm and neural network-based stochastic dynamic programming are also used in a view of comparing model performances. A release curve is developed for every month as a guidance to the decision maker. Simulation has been done for each method using historical actual inflow data, and reliability, resiliency and vulnerability are measured. All model indicators proved that the release policy provided by ABC optimization outperforms in terms of achieving minimum water deficit, less waste of water and handling critical situations.
The Kansas Department of Transportation has a comprehensive pavement management system known as network optimisation system (NOS). Annual condition surveys are conducted for NOS. Currently, the structural number (SN) of flexible pavements is computed using the American association of state highway and transportation officials equation based on the centre and fifth sensor deflections of a falling weight deflectometer (FWD). However, a rolling wheel deflectometer (RWD) can be used to collect deflection data at the network-level. This study was conducted to see whether the SN of flexible pavements can be obtained from this RWD deflection and NOS condition survey results. In this study, FWD deflection data, collected from 1998 to 2006, were analysed. Multiple regression analysis was done. The results showed that there is a negative relationship between SN and centre deflection. Equations can be used to calculate SN based on FWD (or RWD) centre deflections and network-level condition survey results. The SN is more sensitive to centre deflection than the total pavement thickness. 相似文献
Dry (CO2) reforming of methane is conducted over two newly synthesized Ni20/Ce-γAl2O3 and Ni20/Ce-meso-Al2O3 catalysts. The x-ray diffraction (XRD) patterns indicated that Ni20/Ce-meso-Al2O3 exhibits a better dispersion of nickel, while Ni20/Ce-γAl2O3 has larger amounts of nickel crystallites. The temperature programmed desorption (TPD) kinetics analysis indicated that Ni20/Ce-meso-Al2O3 had a lesser metal-support interaction than the Ni20/Ce-γAl2O3. The thermal gravimetric analysis (TGA) indicated that the incorporation of ceria into the Al2O3 matrix helps to stabilize Ni20/Ce-meso-Al2O3 during dry reforming of methane. The temperature programmed reduction (TPR) indicated that the synthesized catalysts were sufficiently reducible below 750 °C. A fixed bed reactor evaluation (at 750 °C) showed that both catalysts can facilitate methane reforming to syngas with minimal coking throughout the 30 hours time-on-stream (TOS). However, Ni20/Ce-meso-Al2O3 is more promising in terms of prolonged stability for dry reforming applications. Moreover, the syngas yield for Ni20/Ce-γAl2O3 is close to equilibrium prediction during the first 1 hour of reaction time. 相似文献