Numerical simulation and optimization of steam-assisted gravity drainage with temperature,rate, and well distance control using an efficient hybrid optimization technique

Steam-assisted gravity drainage (SAGD) is a thermal enhanced oil recovery technique through drilling of two horizontal wells. Effects of steam injection temperature, well rates, and their distance on oil recovery were analyzed and optimized. Steam temperature and well distances remarkably affect SAGD performance. Four metaheuristic algorithms (particle swarm optimization (PSO), imperialist competitive algorithm, cultural algorithm, and Bees algorithm) and pattern search optimization algorithm (PSA) are used for optimization. PSO performs better than other metaheuristics and PSA is the fastest one, while it is probable to be trapped in local optimums. Hybrid PSO-PS is proposed that starts with PSO and proceeds with PSA, and tested in an SAGD project and showed excellence over other techniques.     

Wear and Failure Analysis of Semi-Autogenous Grinding Mill Liners

Journal of Failure Analysis and Prevention - The wear and failure analysis of shell liners of a grinding mill is investigated. Metallurgical and tribological studies were conducted on the worn...     

Photoluminescence emission of nanoporous anodic aluminum oxide films prepared in phosphoric acid

The photoluminescence emission of nanoporous anodic aluminum oxide films formed in phosphoric acid is studied in order to explore their defect-based subband electronic structure. Different excitation wavelengths are used to identify most of the details of the subband states. The films are produced under different anodizing conditions to optimize their emission in the visible range. Scanning electron microscopy investigations confirm pore formation in the produced layers. Gaussian analysis of the emission data indicates that subband states change with anodizing parameters, and various point defects can be formed both in the bulk and on the surface of these nanoporous layers during anodizing.     

WO3 nano-ribbons: their phase transformation from tungstite (WO3·H2O) to tungsten oxide (WO3)

Tungsten oxide (WO₃) nano-ribbons (NRs) were obtained by annealing tungstite (WO₃·H₂O) NRs. The latter was synthesized below room temperature using a simple, environmentally benign, and low cost aging treatment of precursors made by adding hydrochloric acid to diluted sodium tungstate solutions (Na₂WO₄·2H₂O). WO₃ generates significant interests and is being used in a growing variety of applications. It is therefore important to identify suitable methods of production and better understand its properties. The phase transformation was observed to be initiated between 200 and 300 ^°C, and the crystallographic structure of the NRs changed from orthorhombic WO₃·H₂O to monoclinic WO₃. It was rigorously studied by annealing a series of samples ex situ in ambient air up to 800 ^°C and characterizing them afterward. A temperature-dependent Raman spectroscopy study was performed on tungstite NRs between minus 180 and 700 ^°C. Also, in situ heating experiments in the transmission electron microscope allowed for the direct observation of the phase transformation. Powder X-ray diffraction, electron diffraction, electron energy-loss spectroscopy, and X-ray photoelectron spectroscopy were employed to characterize precisely this transformation.     

Improvement of electrochemical and electrical properties of LiFePO<Subscript>4</Subscript> coated with citric acid

LiFePO₄ was synthesized using hydrothermal method and coated with different amounts of citric acid as carbon source.The samples were characterized by X-ray powder diffraction（XRD）,scanning electron microscopy（SEM）,transmission electron microscope（TEM）,surface area measurement—Brunauer–Emmett–Teller（BET）,discharge capability,cyclic voltammetry（CV）,and electrochemical impedance spectroscopy（EIS）.The results show that the quality and thickness of the carbon coating on the surface of LiFePO₄ particles are very important.The optimum carbon content（about 30 wt%）can lead to a more uniform carbon distribution.Electrochemical results show that the samples containing 20 wt%,30 wt%,40 wt%,and50 wt% carbon deliver a discharge capacity of 105,167,151,and 112 mAhg^-1,respectively,at the rate of 0.1C.The increase of carbon content leads to the decrease of discharge capacity of LiFePO₄/C,owing to the fact that excess carbon delays the diffusion of Li⁺ through the carbon layers during charge/discharge procedure.The LiFePO₄/C with low carbon content exhibits poor electrochemical performance because of its low electrical conductivity.Therefore,the amount of carbon must be optimized in order to achieve excellent electrochemical performance of LiFePO₄/C for its application in a lithium ion battery.     

Preparation of novel 2-(2-oxo-2H-chromen-4-yl)-3- arylthiazolidin-4-one derivatives using an efficient ionic liquid catalyst

An eco-friendly procedure for synthesis of 2-(2-oxo-2H-chromen-4-yl)-3-arylthiazolidin-4-one derivatives by three-component reaction of 2-oxo-2H-chromene-4-carbaldehydes, aromatic amines and thioglycolic acid, with tetramethylbutane-1,4-diammonium acetate as a low-cost ionic liquid catalyst under reflux condition is described. The use of an ionic liquid as a catalyst has the advantages of high yields, short reaction time and environmentally friendly reaction media.     

Effects of dynamic vulcanization on tensile,morphological, and swelling properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(Kenaf core powder) composites

The effects of dynamic vulcanization on properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(kenaf core powder) composite were studied. Tensile properties indicated that the strength, elongation at break, and Young's modulus of the composites exhibited an increase for samples with dynamic vulcanization. Morphological analysis using scanning electron microscopy showed the interaction between ENR and PVC. There was no bonding between kenaf core powder and the PVC/ENR matrix owing to the different polarity of both components. Filler agglomerates increased, which leads to an increase of filler‐filler interaction and poor dispersion. Furthermore, swelling index indicated that the composite with dynamic vulcanization shows lower absorption of tolune compared with composites without dynamic vulcanization. J. VINYL ADDIT. TECHNOL., 22:206–212, 2016. © 2014 Society of Plastics Engineers     

Processing and 3D printing of SiCN polymer-derived ceramics

Preceramic polymer resins are attractive for the 3D printing of net-shaped ceramic components. Recently various processes have been demonstrated for 3D printing of polymer-derived ceramics (PDCs). Ultimately in these processes, the process outcomes strongly depend on the process parameters. In particular, for PDCs the ceramic density, and ceramic yield are affected by the catalyst concentration and cross-linking duration. Here, we use thermal analysis and FTIR to quantify the interrelation of the process parameters on the process outcome for polysilazanes and demonstrate 3D printing of PDC components based on the best-identified process parameters. The results of this work can be used as guidelines for future additive manufacturing of PDCs.     

Thermal Stability Investigation of Synthesized Epoxy-Polyurethane/Silica Nanocomposites

Silicon - In this research, epoxy polyurethane-nano silica nanocomposites have been synthesized using an in-situ method, for which SiO2 nanocomposites had been initially ready in N,...