Homogeneous Strain Introduction Using Reciprocation Technique in High-Pressure Sliding

Metallurgical and Materials Transactions A - This study examines strain distribution occurring in the high-pressure sliding (HPS) processing for rods of pure Al and an AZ61 alloy. The strain...     

Improvement in impact strength of modified cardanol‐bonded cellulose thermoplastic resin by using olefin resins

Impact strength of a modified cardanol‐bonded cellulose thermoplastic resin was greatly improved by using a small amount of olefin resins. As we showed, this thermoplastic resin (3‐pentadecylphenoxy acetic acid (PAA)‐bonded cellulose diacetate (CDA): PAA‐bonded CDA) exhibited high practical properties such as bending strength, heat resistance, and water resistance. However, its impact strength was insufficient for use in durable products. We improved the impact strength of PAA‐bonded CDA by adding hydrophobic olefin resins, such as polyethylene or polypropylene, while maintaining good bending strength and breaking strain. Furthermore, the application of olefin resins also increased water resistance and fluidity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39829.     

High-melt-strength polypropylene with electron beam irradiation in the presence of polyfunctional monomers

High-melt-strength polypropylene (PP) was achieved with irradiation by an electron beam generated from an accelerator in the presence of polyfunctional monomers (PFM). Among 16 PFMs, the relatively shorter molecular chain bifunctional monomers such as 1,4-butanediol diacrylate (BDDA) and 1,6-hexanediol diacrylate (HDDA) were the most effective for enhancing the melt strength of PP. The concentration and dose of the HDDA to obtain the high melt strength PP in irradiation under nitrogen gas atmosphere were 1.5 mmol/100 g PP and 1 kGy, respectively. DSC measurement and dynamic mechanical analysis showed that the thermal behavior of the high-melt-strength PP was different from that of the original PP. Crystallinity and crystallization temperature during cooling after heating were lower and higher in high melt strength PP than original PP, respectively. Elongational viscosity at 180°C of the high-melt-strength PP showed a remarkable increase at a certain elongational time with constant strain rate, demonstrating the typical property of high-melt-strength samples. This implies that a few higher molecular chains of PP, formed by intermolecular combination of its chain by HDDA in irradiation, give higher melt strength to induce entanglement of molecular chains. © 1996 John Wiley & Sons, Inc.     

Wave venation in downward gas-liquid two-phase flow (part I,time-spatial behavior chart of interface and analysis of main wave-vein)

Time-series information on both the cross-sectional mean liquid holdup along a tube axis and the gas-liquid phase distribution along a tube diameter was obtained by means of supermultiple cross-sectional mean liquid holdup probes (S-CHOP) and semi-supermultiple point-electrode probes (SS-PEP) for vertical downward gas-liquid two-phase flow. Typical time-spatial behavior charts of interface and gas-liquid interfacial profiles are presented. Close inspection of these results reveals that a huge wave and a disturbance wave appear in downward two-phase flow as well as upward flow. It was clarified that the huge wave flow region covers a wide range of superficial gas velocities. Wave velocity, wave width and maximum liquid holdup of individual waves were examined by wave-vein analysis. Histograms of these flow parameters were also studied. It was found that there exist distinct differences in wave width between the huge wave and the disturbance wave. © 1997 Scripta Technica, Inc. Heat Trans Jpn Res, 25(8): 499–510, 1996     

Development of a new heterojunction structure (ACJ -HIT) and its application to polycrystalline silicon solar cells

A new solar cell structure named HIT (Heterojunction with Intrinsic Thin layer) has been developed based on new artificially constructed junction (ACJ) technology. In this structure a non-doped a-Si thin layer was inserted between the p(a-Si)/n(c-Si) heterojunction, improving the output characteristics and achieving a conversion efficiency of 18.1%. This structure was applied to cast polycrystalline silicon solar cells of a practical size. A high conversion efficeincy of 13.6% was obtained with a cell size of 10 cm × 10 cm using various technologies, including hydrogen plasma passivation.     

Effect of morphology on shear viscosity for binary blends of polycarbonate and polystyrene

The structure and rheological properties of binary blends of polycarbonate (PC) and polystyrene (PS) were investigated using various PS samples with different molecular weights, namely PS1k (M_w = 1,000), PS53k (M_w = 53,000), and PS240k (M_w = 240,000). The blends with PS53k and PS240k show phase-separated structures, whereas the blend with PS1k is miscible. The shear viscosity decreases greatly on addition of PS53k and PS240k, especially at high shear rates, which would be a great advantage at processing operations. Because the nonlinear response occurs in the small strain region for multilayered films of PC and PS240k, the origin of the significant viscosity drop for the phase-separated system is interfacial slippage at the phase boundary.     

Am1 MO Study of Benzene Nitro Derivatives

Molecular properties of benzene nitro derivatives were investigated by using semi-empirical MO calculations. As the results, the molecular structures and the rotational barrier of the nitro group calculated by AM1 showed a good agreement with the experimental values. The heats of formation in gaseous and condensed phases were obtained by considering isodesmic reactions. By this procedure, the heat of formation of hexanitrobenzene in solid phase was calculated to be +22.7 kcal/mol. The detonation parameters were also calculated by using four equations of state. The predicted detonation velocities showed a good agreement with the experimental values.