Effect of unit-cells of the frequency selective surface as superstrate on the directivity of rectangular microstrip antenna

In this paper, the relationship between the number of unit-cells used in the design of a frequency selective surface (FSS) and its expected directivity is established. The relationship between the number of FSS unit-cells and the directivity is based on the planer microstrip patch array antenna design concept where the unit-cell is treated as the superstrate illuminated by the source. To validate the proposed technique, the analytical value of the directivity has been compared with that of ray-tracing method. The directivity of antenna is calculated for two different planar array configurations at 600 GHz. The results of numerical analysis are compared to that of the full-wave electromagnetic simulator CST Microwave Studio and results are comparable. Further, the directivity computed by this proposed technique has also been compared with that of the reported in literatures.     

Recent advances in indium metallurgy: A review

The by-products of zinc refineries are used as the primary mineral resources for the commercial production of indium. The discarded LCDs containing adequate amount of indium is rather worth as its secondary resources compared to the by-products of zinc refineries. Mining and recycling rates of indium, respectively from minerals and waste LCDs are in progress to meet its huge demand. Recycling of the LCDs has been dominating over mining, as presently 480t of indium are produced annually from mining, however, that of 650t annually from recycling. Different aspects of the extractive metallurgy of indium are summarized in this review paper.     

Providing Dynamic Visual Information for Collaborative Tasks: Experiments With Automatic Camera Control

One possibility presented by novel communication technologies is the ability for remotely located experts to provide guidance to others who are performing difficult technical tasks in the real world, such as medical procedures or engine repair. In these scenarios, video views and other visual information seem likely to be useful in the ongoing negotiation of shared understanding, or common ground, but actual results with experimental systems have been mixed. One difficulty in designing these systems is achieving a balance between close-up shots that allow for discussion of detail and wide shots that allow for orientation or establishing a mutual point of focus in a larger space. Achieving this balance can be difficult without disorienting or overloading task participants. In this article we present results from two experiments involving three automated camera control systems for remote repair tasks. Results show that a system providing both detailed and overview information was superior to systems providing only one or the other in terms of performance but that some participants preferred the detail-only system.     

Manganese–Schiff base complex immobilized silica materials for electrocatalytic oxygen reduction

Curtailment of platinum catalysts loading in fuel cell is a recent central issue. As substitutes, these days several organic metal chelate compounds having featured moieties of M–N₄ or M–N₂O₂ (M = transition metal ion) are being used as cathode catalysts in fuel cells. Here, in this study, we report in detail the electrocatalytic activity of manganese–Schiff base complexes for oxygen reduction reaction in 0·05 M HClO₄ at room temperature. Actually, [Mn(salen)]⁺: [N,N′-bis(salicylaldehyde) ethylenediimino manganese(III)]⁺ and [Mn(salophen)]⁺: [N,N′-bis(salicylaldehyde)-1,2-phenylenediimino manganese(III)]⁺ were introduced into/onto the MCM-41 type silica spheres and used for the electrocatalytic reduction of oxygen. Synthesized materials were characterized by UV–Vis, FT–IR and electrochemical techniques. Significant low overpotential for oxygen reduction in 0·05 M HClO₄ on [Mn(salen)]⁺- and [Mn(salophen)]⁺-incorporated silica-modified glassy carbon electrodes was observed.     

Self generating square/triangular wave and pulse width modulator using a single MO-CCCDTA

A self-generating square/triangular wave and pulse width modulator (PWM) using multiple output current controlled current differencing transconductance amplifier (MO-CCCDTA) is presented. To obtain all the three functions simultaneously from the same topology, the MO-CCCDTA is modified a little bit. The characterisation of the modified MO-CCCDTA structure shows that the parasitic resistances at input terminals (n and p) can be varied via bias current. The maximum useful frequency range is found to be 635 MHz, which is higher than the available literature. The waveform generator and PWM circuit use only one MO-CCCDTA, one grounded capacitor and no resistor; hence suitable for IC implementation. The duty cycle of proposed pulse width modulation can be tuned by bias current of MO-CCCDTA over a wide range. The performances of the proposed block and its applications (square/triangular/PWM) are verified by PSPICE simulation using TSMC 0.35 µm technology. The power consumption is about 1.12 mW. To verify experimentally, a prototype of MO-CCCDTA has been made using commercially available ICs (AD844AN and CA3080) on printed circuit board. The simulation and experimental results verify theoretical proposition well. Monte carlo simulation is carried out, which proves satisfactory performance of the proposed circuit against mismatches. The performance of the proposed circuit is also verified through pre-layout and post-layout simulation results. The required chip area is only 22.415 × 14.6 µm².     

Autonomous bioremediation of a microbial protein (bioremediase) in Pozzolana cementitious composite

The self-bioremediation in cementitious composite material is one of the most interesting avenues relating to damage management and self-life of constructions, which needs to be cogitated. The self-bioremediation of a microbial protein-impregnated cementitious material has been explored in this work. The bioremediase protein was isolated from a hot spring bacterium (BKH1) and incorporated at three different concentrations into commercial Pozzolana cements that are widely used for mortar sample preparation. Artificial cracks were generated within the mortar samples by applying partial breaking load (50 %) and the samples were cured under water for different days. Image analysis by Crackscope and microstructure analysis by field emission scanning electron microscope ascertained the formation of irregular crystalline healing material within the cracks of the test samples. X-ray diffractometer and energy dispersive spectra analyses confirmed that the irregular crystalline structures were due to the deposition of new silicate phase (Gehlenite) within the cracks. Increase of ultrasonic pulse velocity and compressive strength, augmentation of sulphate resistance, decrease of chloride permeability and water absorption capacity revealed that there were overall improvement of mechanical properties and durability of the protein-incorporated mortar samples compared to the control (without protein incorporation) mortar samples. This cost effective and eco-friendly self-bioremediation phenomenon observed in mortar is evolved due to the biosilicification activity of bioremediase protein when amended in mortar samples. The exceptional potential of the microbial bioremediase protein for self-bioremediation attribute may add a new dimension in self-healing construction technology in near future.