INTERACTION OF LONG-CHAIN ALCOHOL “MODIFIERS” WITH LIX SOLVENT EXTRACTION REAGENTS

The effect of two long chain alcohols, n-tridecyl alcohol (TDA) and 2-(l,3-trimethylbutyl)-5,7,7-trlinethyloctanol (ODA) on the extraction of Cu by alkylated hydroxyaldoximes in heptane was investigated by extraction equilibrium determination and infrared spectroscopic examination. The formation of an alcohol-extractant association complex quantitatively explains observed decreases in Dcu that accompanies alcohol addition. Further, an examination of Interfacial activity in these systems demonstrates that, whereas alcohol addition decreases the extractant adsorption at the interface, this cannot be attributed to simple displacement (the extractants are significantly more surface active than the alcohols) but rather to its depletion resulting from the formation of the poorly surface active extractant-modifier complex. Values for the Cu-hydroxyaldoxime extraction constants, self-association constants of the extractants, and the alcohols and extractant-modifier complex formation constant are presented. The critical role of infrared spectroscopic measurements in this study is described.     

Nanoindentation of WC–Co hardmetals

WC–Co cemented carbide has been investigated using instrumented indentation with maximum applied loads from 0.1 to 10 mN. The hardness and indentation modulus of individual phases and the influence of crystallographic orientation of WC on the hardness and indentation modulus have been studied. The hardness of the Co binder was approximately 10 GPa and that of WC grains up to 50 GPa with relatively large scatter under the indentation load of 1 mN. Investigation of the role of crystallographic orientation of WC grains on hardness at 10 mN load revealed average values of H_ITbasal = 40.4 GPa (E_ITbasal = 674 GPa) and H_ITprismatic = 32.8 GPa (E_Itprismatic = 542 GPa), respectively. The scatter in the measured values at low indentation loads is caused by the effects of surface and sub-surface characteristics (residual stress, damaged region) and at higher loads by “mix-phase” volume below the indenter.     

Cytokine Receptors—Regulators of Antimycobacterial Immune Response

Cytokine receptors are critical regulators of the antimycobacterial immune response, playing a key role in initiating and coordinating the recruitment and activation of immune cells during infection. They recognize and bind specific cytokines and are involved in inducing intracellular signal transduction pathways that regulate a diverse range of biological functions, including proliferation, differentiation, metabolism and cell growth. Due to mutations in cytokine receptor genes, defective signaling may contribute to increased susceptibility to mycobacteria, allowing the pathogens to avoid killing and immune surveillance. This paper provides an overview of cytokine receptors important for the innate and adaptive immune responses against mycobacteria and discusses the implications of receptor gene defects for the course of mycobacterial infection.     

Long-Term Changes in Ovarian Follicles of Gilts Exposed Neonatally to Methoxychlor: Effects on Oocyte-Derived Factors,Anti-Müllerian Hormone,Follicle-Stimulating Hormone,and Cognate Receptors

In this paper, we investigated the effects of neonatal exposure to methoxychlor (MXC), a synthetic organochlorine used as an insecticide with estrogenic, antiestrogenic, and antiandrogenic activities on ovarian follicles of adult pigs. Piglets were injected with MXC (20 μg/kg body weight) or corn oil (controls) from postnatal Day 1 to Day 10 (n = 5 per group). Then, mRNA expression, protein abundance and immunolocalization of growth and differentiation factor 9 (GDF9), bone morphogenetic protein 15 (BMP15), anti-Müllerian hormone (AMH) and cognate receptors (ACVR1, BMPR1A, BMPR1B, TGFBR1, BMPR2, and AMHR2), as well as FSH receptor (FSHR) were examined in preantral and small antral ovarian follicles of sexually mature gilts. The plasma AMH and FSH levels were also assessed. In preantral follicles, neonatal exposure to MXC increased GDF9, BMPR1B, TGFBR1, and BMPR2 mRNAs, while the levels of AMH and BMP15 mRNAs decreased. In addition, MXC also decreased BMP15 and BMPR1B protein abundance. Regarding small antral follicles, neonatal exposure to MXC upregulated mRNAs for BMPR1B, BMPR2, and AMHR2 and downregulated mRNAs for AMH, BMPR1A, and FSHR. MXC decreased the protein abundance of AMH, and all examined receptors in small antral follicles. GDF9 and BMP15 were immunolocalized in oocytes and granulosa cells of preantral follicles of control and treated ovaries. All analyzed receptors were detected in the oocytes and granulosa cells of preantral follicles, and in the granulosa and theca cells of small antral follicles. The exception, however, was FSHR, which was detected only in the granulosa cells of small antral follicles. In addition, MXC decreased the plasma AMH and FSH concentrations. In conclusion, the present study may indicate long-term effects of neonatal MXC exposure on GDF9, BMP15, AMH, and FSH signaling in ovaries of adult pigs. However, the MXC effects varied at different stages of follicular development. It seems that neonatal MXC exposure may result in accelerated initial recruitment of ovarian follicles and impaired cyclic recruitment of antral follicles.     

The effect of halloysite additive on operation of boilers firing agricultural biomass

The paper presents results of investigations on using halloysite as an additive in biomass-fired boilers. It has been shown that in the case of a few different agricultural biomasses the halloysite addition increased the ash sintering temperature to the values noted for coals. This is an effect of bonding sodium and potassium in the form of chlorides and other compounds. In practical terms the halloysite additive may reduce slagging and fouling of boiler heating surfaces as well as deteriorate the agglomeration processes in fluidized beds. Moreover, addition of halloysite reduces the amount of KCl and NaCl present in ash (and therefore in ash deposits) thus decreasing the rate of high temperature corrosion.     

SBA-15 mesoporous silica modified with rhodium by MDD method and its catalytic role for N<Subscript>2</Subscript>O decomposition reaction

SBA-15 mesoporous silicas modified with rhodium were studied as catalysts for the N₂O decomposition reaction. Rhodium was deposited on SBA-15 by the Molecular Designed Dispersion (MDD) method using Rh(acac)₃ as a precursor of active phase. The same method was used for the deposition of Cu, Fe, Al and Ti. The SBA-15 support modified with metals were characterized with respect to metal loading (EPMA), structure (XRD), texture (BET), morphology (SEM), Rh dispersion (oxygen chemisorption), surface acidity (pyridine adsorption) and chemical nature of introduced copper and iron species (UV–vis-DRS). The rhodium-containing SBA-15 samples were found to be active catalysts for the N₂O decomposition reaction. Deposition of Al on the Rh-loaded catalyst increased its activity. An opposite effect was observed for the samples modified with Cu and Fe.     

Activation of bifunctional coupling agents in fiberglass/polyethylene composites by electron beam

Electron beam (EB) radiation was investigated as a means to initiate coupling between the fiberglass and plastic phases in fiberglass/polyethylene plastic composites using two bifunctional compounds, 12‐azido‐1‐diazo‐2‐dodecanone (A) and 1‐diazo‐17‐octadecene‐2‐one (B). Chemical studies reveal that EB radiation has the potential to bind both of these compounds to fiberglass. Fiberglass coated with either A or B shows reduced values of percentage recovery upon exposure to EB, indicating a reaction between these compounds and the glass surface. However, even 400 kGy of radiation was not as effective as a heat treatment for 45 min at 150°C. To test the effectiveness of EB radiation to couple these compounds to polyethylene, fiberglass samples were heat‐treated with compounds A and B, followed by extrusion mixing with polyethylene, and exposure of molded tensile and impact samples to EB radiation. Compound B showed the best overall ability to couple with the polyethylene matrix, but a 400‐kGy dose was necessary to bring about substantial coupling. At 400 kGy, samples containing B showed a 23% improvement in tensile properties and a 30% change in Izod impact. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2579–2594, 2002     

Bifunctional coupling agents for improved mechanical properties in fiberglass/polyethylene composites

Two bifunctional compounds, 12‐azido‐1‐diazo‐2‐dodecanone (A) and 1‐diazo‐17‐octadecene‐2‐one (B), show an ability to act as coupling agents in fiberglass/polyethylene composites. Under appropriate conditions the diazoketone functional groups in both A and B react with hydroxyl groups on a fiberglass surface, whereas the azide group in A and the alkene group in B form bonds with the plastic matrix during processing. FTIR and NMR spectroscopy were used to study the decomposition of each of these compounds under heat and UV light. Each treatment resulted in a relatively fast decomposition of the diazoketone functional group, along with a slower reaction of the azide and alkene groups. Thus it was possible to react the diazoketone end of these compounds with a fiberglass surface, without affecting the azide or alkene functional groups on the other ends of the molecules. In samples of treated fiberglass containing compounds A or B and mixed by extrusion with polyethylene, the mechanical properties of the composites had improved properties over composites containing untreated samples of fiberglass. With A as the coupling agent, both the tensile properties and Izod impact showed changes that indicated that a bifunctional bridge was formed between the fiberglass and polyethylene phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2562–2578, 2002