Routine bridge inspections usually consist of visual observations. These inspections are time-consuming and subjective. There is a need to identify new inspection techniques for infrastructure that reduce traffic disturbance, and improve the efficiency and reliability of the acquired data. This study compared the performance of three different imaging technologies for the three-dimensional (3D) geometric modeling of existing structures: terrestrial laser scanning, close-range photogrammetry, and infrared scanning. Each technology was used to assess six existing concrete railway bridges. The technologies were compared in terms of geometric deviations, visualization capabilities, the level of the inspector’s experience, and degree of automation. The results suggest that all methods investigated can be used to create 3D models, however, with different level of completeness. Measurements such as span length, deck widths, etc. can be extracted with good accuracy. Although promising, a full off-site inspection is currently not feasible as some areas of the bridges were difficult to capture mainly due to restricted access and narrow spaces. Measurements based on terrestrial laser scanning were closer to the reality compared to photogrammetry and infrared scanning. The study indicates the no special training is needed for photogrammetry and infrared scanning to generate a 3D geometric model. 相似文献
Journal of Chemical Ecology - MACE is an open access collection of electron impact (EI) mass spectra for coupled gas chromatography-mass spectrometry (GC/MS) that serves as an add-on database,... 相似文献
Flowering plants often use chemical signals to attract their pollinators, and compounds that elicit attraction are known for several groups of pollinators. For other pollinators such as gall midges, however, compounds responsible for their attraction to flowers are largely unknown. Here, we describe the pollination biology of Anthurium acutangulum, a Neotropical aroid species found to be attractive to gall midges. We collected and analyzed its floral scent by dynamic headspace collections and gas chromatography coupled to mass spectrometry, and identified compounds responsible for pollinator attraction. The inflorescences were almost exclusively visited by gall midges (females; Cecidomyiidae: Cecidomyiinae) and released a strong scent reminiscent of freshly cut cucumber, mainly (5S,7S)-trans-conophthorin, (E2,Z6)-2,6-nonadienal, and cis-conophthorin. Behavioral assays with the two most abundant compounds identified (E2,Z6)-2,6-nonadienal as being highly attractive to the female gall midge pollinators, whereas (5S,7S)-trans-conophthorin was not attractive. Overall, we introduce a new specialized gall midge pollination system and identify the chemical mediating communication between the pollinators and their host plants.
Fine-tuning of G protein-coupled receptor (GPCR) signaling is important to maintain cellular homeostasis. Recent studies demonstrated that lateral GPCR interactions in the cell membrane can impact signaling profiles. Here, we report on a one-step labeling method of multiple membrane-embedded GPCRs. Based on short peptide tags, complementary probes transfer the cargo (e. g. a fluorescent dye) by an acyl transfer reaction with high spatial and temporal resolution within 5 min. We applied this approach to four receptors of the cardiovascular system: the endothelin receptor A and B (ETAR and ETBR), angiotensin II receptor type 1, and apelin. Wild type-like G protein activation after N-terminal modification was demonstrated for all receptor species. Using FRET-competent dyes, a constitutive proximity between hetero-receptors was limited to ETAR/ETBR. Further, we demonstrate, that ETAR expression regulates the signaling of co-expressed ETBR. Our orthogonal peptide-templated labeling of different GPCRs provides novel insight into the regulation of GPCR signaling. 相似文献
This paper presents a novel fiber spraying process for the manufacturing of short fiber bundle-reinforced Nextel™ 610/Al2O3-ZrO2 oxide fiber composites (SF-OFC) and its characterization. First, the influence of varying fiber lengths (7, 14, and 28 mm, continuous fibers) and fiber orientations (unidirectional 0°, quasi-isotropic, ±45°) was investigated using hand-laid SF-OFC. Due to the weak matrix, the hand-laid material exhibited a strongly fiber-dominated material behavior, that is, variations in fiber length and orientation had a strong influence on the material properties. Second, the automated sprayed SF-OFC, however, exhibited a random orientation of the fiber bundles, which resulted in in-plane isotropic material properties. Average bending strengths of up to 177 MPa, strains of .39%, and a quasi-ductile fracture behavior were achieved. The strain was, therefore, in the range of fabric-reinforced OFC. While the bending strength of the SF-OFC was somewhat lower than that of fabric-reinforced OFC with the fiber orientation parallel to the loading direction, it was more than two times higher than the strength in 45° direction relative to the fabric reinforcement. Combined with good drapability and lower material costs compared to fabric-reinforced OFC, SF-OFC is, therefore, a promising material for industrial applications. 相似文献
Powder Metallurgy and Metal Ceramics - In this study, different heat treatment regimes, such as sintering, sintering with low-pressure cementation, and only low-pressure cementation were applied to... 相似文献
Thermal loading induces modifications of the precipitation microstructure of Al–Si–Cu–Mg alloys. This study focuses on the effect of deformation on precipitation microstructure during thermomechanical loadings. Several specimens were thermomechanically cycled while others were exposed to the same thermal cycles without any mechanical loading. The nature and morphological characteristics of the precipitation microstructure of the thermomechanically cycled specimens are compared to those of the thermally aged ones, using transmission electron microscopy (TEM), in order to assess the effect of deformation on the precipitation microstructure and especially on the kinetics of precipitate growth. The absence of any significant effect of superimposed straining during thermal cycling is discussed. Implications for the prevision of yield strength degradation during service operation are briefly presented.
This article presents numerical simulations of the laminar flow of lubricating greases in a channel with rectangular cross section. Three greases with different consistencies (NLGI grades 00, 1, and 2) have been considered in three different configurations composed of a rectangular channel without restrictions, one rectangular step restriction, and one double-lip restriction. The driving pressure drop over the channel spans from 30 to 250 kPa. The grease rheology is described by the Herschel-Bulkley rheology model, and both the numerical code and rheology model have been validated with analytical solutions and flow measurements using micro-particle image velocimetry. 相似文献