Gaussian beam ray-equivalent modeling and optical design

It is shown that the propagation and transformation of a simply astigmatic Gaussian beam by an optical system with a characteristic ABCD matrix can be modeled by relatively simple equations whose terms consist solely of the heights and slopes of two paraxial rays. These equations are derived from the ABCD law of Gaussian beam transformation. They can be used in conjunction with a conventional automatic optical design program to design and optimize Gaussian beam optical systems. Several design examples are given using the CODE-V optical design package.     

Oxidation resistant Mo-Mo<Subscript>2</Subscript>B-silica and Mo-Mo<Subscript>2</Subscript>B-silicate composites for high temperature applications

Development of Mo composites based on the Mo-Si-B system has been demonstrated as a possible new route to achieving a high temperature Mobased material. In this new system, the silicide phases are replaced directly with silica or other silicate materials. These composites avoid the high ductile to brittle transition temperature observed for Mo-Si-B alloys by removing the Si that exists in solid solution in Mo at equilibrium with its silicides. A variety of compositions is tested for room temperature ductility and oxidation resistance. A system based upon Mo, Mo₂B, and SrO·Al₂O₃·(SiO₂)₂ is shown to possess both ductility at 80 vol.% Mo and oxidation resistance at 60 vol.%. These composites can be produced using a powder processing approach and fired to greater than 95% theoretical density with a desirable microstructure of isolated boride and silicate phases within a ductile Mo matrix.     

Factors affecting the correlation coefficient template matching algorithm with application to real-time 2-D coronary artery MR imaging

This paper characterizes factors affecting the accuracy of the correlation coefficient (CC) template matching algorithm, as applied to motion tracking from two-dimensional real-time coronary artery magnetic resonance images. The performance of this algorithm is analyzed in the presence of both random and systematic error. In the presence of random error, it is shown that a necessary and sufficient condition for accurate motion tracking is a large CC difference-to-noise ratio (CCDNR). The CCDNR itself is in turn affected by five factors: image and template size, image and template structure, and the magnitude of the noise. Techniques are introduced for manipulating some of these factors in order to increase the CCDNR for greater motion tracking accuracy. In the presence of superimposed systematic error it is shown that, while large CCDNR is necessary, it alone is not sufficient to ensure accurate motion tracking. Techniques are developed for improving motion tracking accuracy that minimize the effects of systematic error, while maintaining an adequate CCDNR level. The ability of these techniques to improve motion tracking accuracy is demonstrated both in phantoms and in coronary artery images.     

Statistical coding method for facial features

Model-based techniques have been shown to give high compression rates for coding head and shoulder image sequences, typically for videophone applications. However, they lead to poor image quality in significant areas of the face such as the eyes and mouth. To overcome this problem, a hybrid system could be perceived where the facial features were represented using traditional statistical techniques and the remaining of the head and shoulder sequences using highly efficient model-based methods, therefore utilising more bits to code the sensitive areas and fewer for the rest. In the paper, the method of principal component analysis to code the dynamic changes in a sequence is presented     

Diode-pumped ytterbium-doped Sr5(PO4)3F laser performance

The performance of the first diode-pumped Yb³⁺-doped Sr ₅(PO₄)₃F (Yb:S-FAP) solid-state laser is discussed. An InGaAs diode array has been fabricated that has suitable specifications for pumping a 3×3×30 mm Yb:S-FAP rod. The saturation fluence for diode pumping was deduced to be 5.5 J/cm ² for the particular 2.8 kW peak power diode array utilized in our studies. This is 2.5× higher than the intrinsic 2.2 J/cm ² saturation fluence as is attributed to the 6.5 nm bandwidth of our diode pump array. The small signal gain is consistent with the previously measured emission cross section of 6.0×10^-20 cm², obtained from a narrowband-laser pumped gain experiment. Up to 1.7 J/cm³ of stored energy density was achieved in a 6×6×44 mm Yb:S-FAP amplifier rod. In a free running configuration, diode-pumped slope efficiencies up to 43% (laser output energy/absorbed pump energy) were observed with output energies up to ~0.5 J per 1 ms pulse. When the rod was mounted in a copper block for cooling, 13 W of average power was produced with power supply limited operation at 70 Hz with 500 μs pulses     

Power IC with EEPROM programmable switch mode regulators

A power IC is described with an EEPROM programmable trim for precision regulation of two switch-mode regulators and a high accuracy oscillator. In-the-package voltage adjustment to 1% and an oscillator trim of 1.5% are achieved with the internal trim capability. The IC also features an “H” bridge for DC motor control and eight low-side drivers for driving unipolar stepper motors. A modified 44 pin plastic leaded chip carrier gives 30°C/W performance     

Toughening Mechanisms in Cemented Carbides

Plastic zones much larger than previously expected have been observed around cracks in several cemented carbide materials. A preliminary estimate of the crack tip shielding due to the plastic zone in one material suggests that a substantial fraction of the fracture toughness may be due to the zone. Moreover, reduced zone sizes were observed in regions of rapid crack growth, implying that the dynamic fracture toughness may be smaller than the quasi-static value.     

On the Thermoelastic Martensitic Transformation in Tetragonal Zirconia

Recent evidence is summarized showing that the tetragonal ( t ) → monoclinic ( m ) martensitic transformation in ZrO₂ can occur thermoelastically in certain ZrO₂-containing ceramics, and that microcracking accompanying the transformation is more common than had previously been recognized. The implications of these new data for the conditions under which the stress-induced transformation is irreversible, and for the particle size dependence of the transformation start ( M _s), temperature, are discussed.     

Cyclic Fatigue-Crack Propagation in Magnesia-Partially-Stabilized Zirconia Ceramics

The subcritical growth of fatigue cracks under (tension-tension) cyclic loading is demonstrated for ceramic materials, based on experiments using compact C(T) specimens of a MgO-partially-stabilized zirconia (PSZ), heat-treated to vary the fracture toughness K _c from ∼3 to 16 MPa·m^1/2 and tested in inert and moist environments. Analogous to behavior in metals, cyclic fatigue-crack rates (over the range 10⁻¹¹ to 10⁻⁵ m/cycle) are found to be a function of the stress-intensity range, environment, fracture toughness, and load ratio, and to show evidence of fatigue crack closure. Unlike toughness behavior, growth rates are not dependent on through0-thickness constraint. Under variable-amplitude cyclic loading, crack-growth rates show transient accelerations following low-high block overloads and transient retardations following high-low block overloads or single tensile overloads, again analogous to behavior commonly observed in ductile metals. Cyclic crack-growth rates are observed at stress intensities as low as 50% of K _c , and are typically some 7 orders of magnitude faster than corresponding stress-corrosion crack-growth rates under sustained-loading conditions. Possible mechanisms for cyclic crack advance in ceramic materials are examined, and the practical implications of such "ceramic fatigue" are briefly discussed.     

Application-level Programmable Internetwork Environment

Future requirements for a broadband multimedia network are likely to be very different from those today. Three key changes are identified — rapid introduction of new services, dynamic customisation of services by clients, and minimal management overhead. Application-layer active networking, perhaps the most pragmatic and immediately realisable active network proposal, is a potential solution to all three. In the 'Management of Multiservice Networks' project, BT and its academic partners are developing key middleware components required to support application-layer active networking.