EFFECTS OF OPERATIONAL CONDITIONS ON DRYING CHARACTERISTICS IN CLOSED SUPERHEATED STEAM DRYING

The effects of operational conditions on the drying performance in closed superheated steam drying were examined theoretically and experimentally. The vapor generated from the sample was circulated in the drying chamber. In the theoretical analysis, the replacement of air with vapor in drying chamber and the convective vapor transfer in sample were considered. At the start of drying, the drying chamber was filled with air. As the drying proceeded, the air was replaced with the vapor generated from sample. The calculated results explained the characteristics of experimental data. The pore diameter of sample had little effect on the drying characteristics. During the internal evaporation period, the evaporation occurred in the narrow zone, which moved from the surface to the bottom of sample. The convective vapor transfer in sample had a significant influence on the drying performance. The excess increments in temperature and velocity of drying gas hardly contributed to shortening the drying time.     

Synchronal measurement of flow structure and heat transfer of impingement jet

This paper will present the characteristics of flow behavior and thermal field of both free and
impingement jet issued from a circular orifice nozzle at Re=8900.The flow behavior of a single round
jet and impingement jet was observed by smoke flow visualization recorded by a high speed camera
using 5000 frame per second.Heat transfer coefficient on the impingement surface was measured by
means of infrared camera （TVS-8500,Avio） with a two-dimensional array of Indeum-Antimony （In Sb）
sensors varying in the separation distance between the nozzle and the target plate.The heat transfer
coefficient changes in time and spatial.Therefore,the root mean square distribution of the heat
transfer was obtained from the data.As a result,it was confirmed that the longitudinal vortex was
observed outside of the ring vortex,and then the longitudinal vortex was penetrated in the jet
flow.Moreover,the high value of root mean square of the heat transfer coefficient has spread radially
in stripy manner,which is caused as the results of the longitudinal vortexes flowing in the radial
direction on the impingement plate.     

Thermal Decomposition of Titanium Alkoxide and Silicate Ester in Organic Solvent: A New Method for Synthesizing Large-Surface-Area, Silica-Modified Titanium(IV) Oxide of High Thermal Stability

Silica-modified titanium oxide (S-TiO₂) powders that have an anatase structure were synthesized via the thermal decomposition of mixtures of titanium(IV) isopropoxide (TIP) and tetramethyl orthosilicate (TMOS) in toluene at 300°C. These S-TiO₂ materials had high rutile-transformation temperatures and maintained large surface areas at elevated temperatures (550°–1000°C). For example, the product that was prepared from a 9:1 TIP:TMOS mixture transformed to rutile at ∼1100°C and possessed a surface area of 160 m²/g, even after calcination at 800°C for 1 h.     

Effect of packed structure on flow behaviour in a trickle bed biofilter

The effects of operation conditions on the flow behaviour in gas–liquid countercurrent trickle bed biofilter were experimentally examined. In order to prevent gas channelling in the biofilter, packings with a relatively large void fraction, which have a role to maintain a high void fraction in the bed, were added. The gas and liquid velocities of the packed structure and the packings were changed, and the residence time distributions (RTDs) of the gas and liquid were measured. It was found that the addition of void supporters was very effective in the suppression of gas channelling.     

Diesel emission control system using combined process of nonthermal plasma and exhaust gas components' recirculation

A NO_x aftertreatment system, using nonthermal plasma (NTP) reduction and exhaust gas components' recirculation, is investigated. A pilot-scale system is applied to a stationary diesel engine. In this system, NO_x is first removed by adsorption, and subsequently, the adsorbent is regenerated by thermal desorption. NO_x desorbed is reduced by using nitrogen NTP. Moreover, NO_x, CO₂, and water vapor recirculated into the engine intake reduce NO_x. In this study, approximately 57% of the NO_x of the exhaust (NO_x: 240-325 ppm, flow rate = 300 NL/min) can be continuously treated for 58 h. A system energy efficiency of 120 g (NO₂)/kWh is obtained.     

Uniform carbon‐nanotube emitter for field‐emission displays

Abstract— The synthesis of carbon‐nanotube (CNT) field emitters for FEDs by thermal chemical vapor deposition (CVD) and their structural and emission characterization are described. Multi‐walled nanotubes (MWNTs) were grown on patterned metal‐base electrodes by thermal CVD, and the grown CNTs formed a network structured layer covering the surfaces of the metal electrode uniformly, which realized uniform distribution of electron emission. A technique for growing narrow MWNTs was also developed in order to reduce the driving voltage. The diameter of MWNT depends on the growth temperature, and it has changed from 40 nm at the low temperature (675°C) to 10–15 nm at the high temperature (900–1000°C). Moreover, narrower MWNTs were grown by using the metal‐base electrode covered with a thin alumina layer and a metal catalyst layer. Double‐walled nanotubes (DWNTs) were also observed among narrow MWNTs. The emission from the narrow CNTs showed a low turn‐on electric field of 1.5 V/μm at the as‐grown layer.     

Slow crystallization process from amorphous PbTiO3

The effect of isothermal annealing of amorphous PbTiO₃ at a temperature below the crystallization temperature, T_crys, has been investigated. Time dependent dielectric constant in the annealing process has been observed. From the experimental results, both the existence of the glass transition temperature, T_g, and the steadiness of dielectric constant at room temperature have been established.     

Analysis of 3D face forms for proper sizing and CAD of spectacle frames

Three-dimensional morphological variations in the human face were analysed using digital models of the human face, and the usefulness of such analysis in designing industrial products was demonstrated by validating spectacle frame designs based on an original sizing system developed based on the analysis. A normalized model of the three-dimensional face form was made for each of 56 young adult Japanese males. The morphological distances between subjects were defined, and subjects were divided into four groups based on analysis of the distance matrix. A prototype spectacle frame was designed for the average form of each of the four groups. Tightening force of the prototype frames was adjusted using the materialized average forms with soft material placed at the nasal bridge and side of the head. Four prototype frames as well as a conventional frame were evaluated using sensory evaluation and physical measurement of the pressure and slip in 38 young adult male subjects. For each of the 38 subjects, prototype frames were ranked according to the morphological similarity of the subjects and the average form of the four groups: the frame designed for the average form of the group most similar to the subject was #1, the frame designed for the average form of the next most similar group was #2, and so on. For the groups with smaller or narrower faces, new frame #1 was most preferred and had the best overall fit, smallest slip sensation and largest pressure sensation. The groups with larger or wider faces preferred tighter frames than new frame #1, because they were concerned that the frames might slip, although the frames did not. Most of the subjects habitually wore spectacles, and the reason that groups with larger or wider faces preferred tighter frames was thought to be that they were accustomed to tighter fitting frames.