Correlation between friction of articular cartilage and reflectance intensity from superficial images

The lubrication mechanism of articular cartilage is characterized by an efficient performance. In this work, friction of articular cartilage was evaluated with in-site images of articular surface. The images were captured with the laser light reflected at the interface between a prism and articular cartilage. The attenuation of reflectance was associated with the increase of the contact of collagen network of articular cartilage. The light reflectance and friction coefficient for short sliding presented a significant positive correlation. Friction tests were also carried out for short (30 s) and long (300 s) preloading times. The results indicate that depletion of fluid film is responsible for the increase of friction and the recovery of the fluid film was observed for the long preloading after the early stage of sliding.     

Effect of concurrent use of ondansetron hydrochloride and dexamethasone against nausea and vomiting in lung cancer patients receiving cisplatin

We examined the efficacy of concurrent use of ondansetron hydrochloride and dexamethasone, and the effective dose of dexamethasone against nausea and vomiting in lung cancer patients receiving chemotherapy including single high dose cisplatin. The study was carried out on total of 44 courses of chemotherapy in either initial onset or recurrence of lung cancer. The patients were given 4 mg of ondansetron injection on the day of cisplatin injection (Day 1), and 4 mg/day of ondansetron tablet for Days 2 to 4. These patients were randomly allocated into 2 groups, i.e., those who, on Day 2, concomitantly received 10 mg of dexamethasone (D10 Group, 22 courses) or 20 mg (D20 Group, 22 courses), for comparing the antiemetic effects in a different concomitant dose of dexamethasone. An efficacy rate of 70% or more was achieved in each group for acute emesis on Day 1. The efficacy rate was 80% or above for emesis on Day 2 when dexamethasone was concurrently administered, and Days 3 and 4 in both groups. No significant difference was observed between the groups. A higher complete suppression rate against nausea was seen in D20 Group even though the difference from D10 Group was not significant. Furthermore, food intake rate on Day 2 was significantly better in D20 Group. However, in the cases that were graded effective or markedly effective for acute emesis on Day 1, the efficacy rate was also high in both groups through Days 2-4. It was notable that the efficacy rate of Days 2-4 was 100% in D2 Group. The high efficacy rate was shown in male patients regardless of which dose of dexamethasone was used. However, control of emesis was unfavorable in female patients on Day 1 and was still unfavorable even though dexamethasone was combined from Day 2. We considered from the above results that 10 mg/day of concurrent dexamethasone is sufficient in suppression of delayed emesis on Day 2. However, in order to improve nausea or food intake, or to suppress emesis in patients who are highly likely to show unfavorable control for Day 2 and onward, 20 mg/day should also be effective.     

High-energy x-ray microbeam with total-reflection mirror optics

Total-reflection mirror optics for high-energy x-ray microfocusing have been developed, and tested in the energy range of 30-100 keV at beamline 20XU of Synchrotron Radiation Facility SPring-8. The optical system consists of a Kirkpatrick-Baez-type [J. Opt. Soc. Am. 38, 766 (1548)] focusing optics with aspherical total-reflection mirrors for the purpose of reducing the spherical aberrations. A focused beam size of 0.35 x 0.4 microm(2) has been achieved at an x-ray energy of 80 keV, and the measured spot size was less than 1 microm in the x-ray energy region below 90 keV.     

Ultra-high-precision time control system over any long time delay for laser pump and synchrotron x-ray probe experiment

An ultra-high-precision clock system for long time delay has been developed for picosecond time-resolved x-ray diffraction measurements using synchrotron radiation (SR) pulses and synchronized femtosecond laser pulses. The time delay control between pump laser pulse and the probe SR pulse was achieved by combining an in-phase quadrature modulator and a synchronous counter. This method allowed us to change the delay time by a nearly infinite amount while maintaining the precision of +/-8.40 ps. Time-resolved diffraction measurements using the delay control system were demonstrated for precise measurement of an acoustic velocity in a single crystal of gallium arsenide.     

Question hard, answer simply: A comment on Storms et al. (2003).

It seems clear that, for whatever reasons, the dementia of the Alzheimer type patient group (as well as other patient groups) exhibits behavior that is different from the normal control group. G. Storms, T. Dirikx, J. Saerens, S. Verstraeten, and P. P. De Deyn (2003) rightfully argue that the observed behavior (similarity judgments) does not tell us the source (cause) of the differences between the 2 groups. Rather, the focus of the study should be placed more on finding the ways the 2 groups are different. They also point out various methodological problems in some of the previous attempts to characterize the nature of the differences. Further methodological issues in G. Storms et al.'s study are examined. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

The relationship between acoustic emission signals and cutting phenomena in turning process

The development of intelligent manufacturing by using machine tools is advancing in leaps and bounds. To maintain accuracy in machining and in the interests of fail-safe operation, monitoring of the cutting state or the final machining is very important. Acoustic emissions (AE) comprise elastic stress waves produced as a result of the deformation and fracture of materials. By measuring the AE generated during a turning process, it is possible to estimate the state of the machining operation. The correlation between cutting phenomena and AE in a turning process was examined experimentally by using a steel workpiece and a cermet tool in a numerically controlled turning process. The process of formation of chips, the types of chip, and the shear angle all markedly affected the AE signals. There was a strong negative correlation between the shear angle and the AE signal level. Similar results were obtained for various feed rates and for workpieces of various degrees of hardness. Correlations related to surface roughness and to tool wear are also described that permit the evaluation of the state of the turning process.     

Low-Temperature Processing and Mechanical Properties of Zirconia and Zirconia–Alumina Nanoceramics

The 1.5- to 3-mol%-Y₂O₃-stabilized tetragonal ZrO₂ (Y-TZP) and Al₂O₃/Y-TZP nanocomposite ceramics with 1 to 5 wt% of alumina were produced by a colloidal technique and low-temperature sintering. The influence of the ceramic processing conditions, resulting density, microstructure, and the alumina content on the hardness and toughness were determined. The densification of the zirconia (Y-TZP) ceramic at low temperatures was possible only when a highly uniform packing of the nanoaggregates was achieved in the green compacts. The bulk nanostructured 3-mol%-yttria-stabilized zirconia ceramic with an average grain size of 112 nm was shown to reach a hardness of 12.2 GPa and a fracture toughness of 9.3 MPa·m^1/2. The addition of alumina allowed the sintering process to be intensified. A nanograined bulk alumina/zirconia composite ceramic with an average grain size of 94 nm was obtained, and the hardness increased to 16.2 GPa. Nanograined tetragonal zirconia ceramics with a reduced yttria-stabilizer content were shown to reach fracture toughnesses between 12.6–14.8 MPa·m^1/2 (2Y-TZP) and 11.9–13.9 MPa·m^1/2 (1.5Y-TZP).     

Effect of oxygen flow rate on the structural and electrochemical properties of lithium nickel oxides synthesized by the sol–gel method

The structural and electrochemical properties of LiNiO₂ powders were investigated as a function of the oxygen flow rate employed in the preparation of lithium nickel oxide. It was found that oxygen played an important role in the synthesis of highly crystallized LiNiO₂(R3¯m). In the crystallization process of LiNiO₂, a deficiency of oxygen in the calcination reactor induced the formation of impurities and cubic rock-salt structure (Fm3m) in LiNiO₂ powders. For LiNiO₂ prepared at higher oxygen flow rates, the electrode delivered high discharge capacities with relatively good retention rates. But very low electrode capacity was obtained from LiNiO₂ prepared at lower oxygen flow rates.     

Alteration of substrate specificity of cholesterol oxidase from Streptomyces sp. by site-directed mutagenesis

Despite the structural similarities between cholesterol oxidasefrom Streptomyces and that from Brevibacterium, both enzymesexhibit different characteristics, such as catalytic activity,optimum pH and temperature. In attempts to define the molecularbasis of differences in catalytic activity or stability, substitutionsat six amino acid residues were introduced into cholesteroloxidase using site-directed mutagenesis of its gene. The aminoacid substitutions chosen were based on structural comparisonsof cholesterol oxidases from Streptomyces and Brevibacterium.Seven mutant enzymes were constructed with the following aminoacid substitutions: L117P, L119A, L119F, V145Q, Q286R, P357Nand S379T. All the mutant enzymes exhibited activity with theexception of that with the L117P mutation. The resulting V145Qmutant enzyme has low activities for all substrates examinedand the S379T mutant enzyme showed markedly altered substratespecificity compared with the wild-type enzyme. To evaluatethe role of V145 and S379 residues in the reaction, mutantswith two additional substitutions in V145 and four in S379 wereconstructed. The mutant enzymes created by the replacement ofV145 by Asp and Glu had much lower catalytic efficiency forcholesterol and pregnenolone as substrates than the wild-typeenzyme. From previous studies and this study, the V145 residueseems to be important for the stability and substrate bindingof the cholesterol oxidase. In contrast, the catalytic efficiencies(k_cat/K_m) of the S379T mutant enzyme for cholesterol and pregnenolonewere 1.8- and 6.0-fold higher, respectively, than those of thewild-type enzyme. The enhanced catalytic efficiency of the S379Tmutant enzyme for pregnenolone was due to a slightly high k_catvalue and a low K_m value. These findings will provide severalideas for the design of more powerful enzymes that can be appliedto clinical determination of serum cholesterol levels and assterol probes.     

Preparation and Luminescence Spectra of Calcium- and Rare-Earth (R = Eu, Tb, and Pr)-Codoped α-SiAlON Ceramics

Rare-earth-doped oxynitride or nitride compounds have been reported to be luminescent and may then serve as new phosphors with good thermal and chemical stabilities. In this work, we report the photoluminescence (PL) spectra of europium-, terbium-, and praseodymium-doped Ca-α-SiAlON ceramics. The highly dense ceramics were prepared by hot pressing at 1750°C for 1 h under 20 MPa in a nitrogen atmosphere. Europium-doped Ca-α-SiAlON displayed a single broad emission band peaking at λ= 550–590 nm depending on the europium concentration. The emission bands in the spectra of europium-doped Ca-α-SiAlONs were assigned to the allowed transition of Eu²⁺ from the lowest crystal field component of 4 f ⁶5 d to ⁸S_7/2 (4 f ⁷) ground-state level. The emission spectra of terbium- and praseodymium-doped Ca-α-SiAlON ceramics both consisted of several sharp lines, which were attributed to the ⁵D₄→⁷F _j ( j = 3, 4, 5, 6) transitions of Tb³⁺ and ³P₀→³H _j ( j = 3, 4, 5) transitions of Pr³⁺, respectively. In particular, the terbium-doped α-SiAlON ceramics showed a strong green emission among these phosphors.