Dielectric Depression and Dispersion in Electrophoretically Fabricated BaTiO3 Ceramic Films

Dielectric depression and dispersion were observed in BaTiO3 ceramic films fabricated by electrophoretic deposition followed by sintering. The dielectric constants were depressed down to 6800–4600 around the Curie point ( T _C ). The dielectric dispersion occurred above T _C . These dielectric properties are attributable to a surface layer formed during sintering. XRD analysis indicated that the surface layer was a hexagonal-like BaTiO₃ phase. A mixed solvent of acetylacetone and alcohol employed in the present work may have been responsible for the formation of the surface layer.     

Characterization of Silicon Carbide–Silicon Nitride Composite Ultrafine Particles Synthesized Using a CO2 Laser by Silicon-29 Magic Angle Spinning NMR and ESR

The structure of silicon carbide–silicon nitride (SiC–Si₃N₄) composite particles synthesized using a CO₂ laser was studied by magic angle spinning nuclear magnetic resonance (MAS-NMR) and electron spin resonance (ESR). The structure around Si atoms changed by introducing N. C atoms around Si were substituted by N atoms, and N-rich configurations around Si atoms increased stepwise as the N content increased. The low N content composite particles consisted of mainly SiC phase containing dissolved N. N atoms were partly present in β-SiC microcrystal and partly in the grain boundary layer in the particle. N atoms were tetrahedrally surrounded by four Si atoms in β-SiC microcrystal and were trivalent state bonded to three Si atoms in the grain boundary layer. The high N content particles consisted of SiC, Si₃N₄, and amorphous phases, whose amount depended on N content.     

Formation of Small-Sized CdSxSe1-x Crystals in Sol-Gel-Derived SiO2 Glasses

Silica glasses doped with small-sized CdS_x-Se_1-x crystals were prepared by the sol-gel method. Gels synthesized by the hydrolysis of Si(OC₂H₅)₄, in the presence of CdSeO₄ with NH₄SCN dissolved in HNO₃ or NH₄OH, were heated in H₂-N₂ atmosphere. The pH value of solutions for CdSeO⁴ and NH⁴SCN primarily determined the fraction of anions in CdS^xSe^1-x crystals. The anion content in crystals was dependent on the pH value of the solvent and/or heat-treatment temperature, and the sulfur fraction changed from 0.1 to 0.6. The optical absorption spectra were red-shifted as the selenium content and the crystal size increased, and the emission spectra showed a sharp band near the absorption edge position and a broad tail extending into the long wavelength. The optical band gap energies increased reciprocally proportional to the square of the crystal size.     

Ring hydrogenation of naphthalene and 1-naphthol over supported metal catalysts in supercritical carbon dioxide solvent

Catalytic ring hydrogenations of naphthalene and 1-naphthol were studied over several supported metal catalysts in supercritical carbon dioxide solvent at low temperature. Higher concentration of hydrogen in supercritical carbon dioxide and lower reaction temperature were responsible for higher catalyst activity and selectivities to the desired partial ring hydrogenated products as compared with those observed in organic solvent for the same catalyst.     

Dehydration of Gels and Glasses in the Systems B2 O3-SiO2 and ZrO2-SiO2 Prepared by the Sol-Gel Process from Metal Alkoxides

Dehydration of gels prepared by the sol-gel process from metal alkoxides in the systems B₂O₃-SiO₂ and ZrO₂-SiO₂ was determined by measuring the shrinkage of the gel on heating. Dehydration was enhanced with increased ZrO₂ content, whereas it decreased with B₂O₃ content. Diffusion of water was also measured in the nonporous glasses obtained by heating the gels. The diffusion rate was independent of the composition of the glass.     

Predicted and observed initial short circuit current for lead-acid batteries

Initial short circuit currents have been observed using our electronic short circuit switch and also predicted from terminal voltage and ohmic resistance according to Ohm's law for several kinds of lead-acid batteries in various states-of-charge. Ohmic resistance was measured by the d.c. step and the a.c. impedance methods. The predicted and the observed values have been compared in order to establish a prediction method for initial short circuit current. A good agreement was obtained, the root mean square percentage deviation of the predicted value from that observed being only 219%, which confirms the validity of the prediction method for the initial short circuit current.     

The Roles of 3- and 4-Isopropylbiphenyls in the Isopropylation of Biphenyl over a H-Mordenite

The isopropylation of mixtures of 3- and 4-isopropylbiphenyls (3- and 4-IPBPs) was examined over a dealuminated H-mordenite (HM) to elucidate the role of 3- and 4-IPBPs in the isopropylation of biphenyl (BP). 4-IPBP was consumed much faster than 3-IPBP in all cases. 4-IPBP was an exclusive precursor to diisopropylbiphenyls (DIPBs), particularly 4,4-DIPB, and 4,4-DIPB was found in encapsulated products during the reaction. These results show that 4-IPBP can allow establishment of an active complex with propylene and acid site in HM pores, whereas 3-IPBP cannot. It is concluded that the isopropylation of BP over HM occurs through a reactant selectivity mechanism, and through a restricted transition state mechanism, but not through a product selectivity mechanism.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Alternative technologies for biotechnological fuel ethanol manufacturing

The challenges of implementing biorefineries on a global scale include socioeconomic, financial, and technological constraints. In particular, the development of biorefineries is tightly linked to the continued availability of fermentation raw materials. These constraints can be relaxed by the use of diverse raw materials, while advances that confer higher flexibility would enable biotechnological plant managers to swiftly react to volatile markets. In conventional processes, Saccharomyces cerevisiae grows on a relatively limited range of substrates, and produces only a single product—ethanol. Given the observed maturity of the S. cerevisiae fermentation technology, alternatives to baker's yeast may be needed to tip the economic balance in favour of biotechnological ethanol. These alternative fermentation technologies may allow a greater diversity of substrates to be used to produce an individually tailored mix of ethanol and other chemicals. Copyright © 2007 Society of Chemical Industry