Oscillation of a tilted circular pad on a droplet for the self-alignment process

The seesaw-oscillation of a small circular pad on a single droplet was studied both numerically and experimentally. The circular pad with a diameter of 2.0–3.8 mm onto a water or glycerol droplet with a volume of 1–10 μL, and a bottom substrate with a smaller diameter than that of the pad were used in the experiment. The pad was then tilted and then the tilting fixture was quickly removed. The pad alternately oscillated and then finally stabilized in a horizontal position. The numerical model considering the surface tension and the viscous force of the droplet was developed and calculated using the same configurations as those in the experiment. The experimental and numerical data showed good agreement not only in terms of the oscillating frequency and damping ratio but the transient motion of the circular pad and instantaneous droplet surface shape.     

Preparation and electrooptical properties of liquid crystal dispersed film by electron-beam irradiation

Polymer films consisting of nematic liquid crystal (LC) droplets and polymer networks were prepared by using a low-energy electron beam to irradiate a homogeneous mixture of nematic LC and bifunctional methacrylate monomer. Influences of such polymerization conditions as polymerization temperature, monomer concentration, and radiation energy on electrooptical properties of the compound films were examined. The polymer yield, affecting to a large extent the film properties, depended on the monomer concentration and the radiation energy. Compound films, which have a switching function from the scattering state to transparency by applying approximately 20–30 V between the two sides of the film, were obtained. In addition, it was found that a compound film with excellent electrooptical properties was prepared by changing impure LC in the droplets into pure LC. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:1675–1681, 1997     

Influence of activated carbon pore structure on oxygen reduction at catalyst layers supported on rotating disk electrodes

Carbon materials are often used as catalyst supports, and for catalysts in electrodes of a polymer electrolyte fuel cell, carbon black has been used. Recently, it was found, however, that activated carbon could replace carbon black and besides, significantly improve the activity of the electrode catalyst layer for oxygen reduction. In the present study, to optimize the pore structure of activated carbon for further activity improvement, the influence of the pore structure on the activity was investigated using activated carbon of various specific surface areas and mean pore diameters. A catalyst layer was formed from activated carbon loaded with platinum and a polymer electrolyte. The activity of the layer was measured in an oxygen-saturated perchloric acid solution, supporting the layer on a rotating glassy carbon disk electrode. We found that increases in the specific surface area and mean pore diameter increased the activity and that the latter was more effective than the former mainly due to the enhanced mass-transfer in the pores; the catalyst layer formed from activated carbon with the largest mean pore diameter was the most active. Unless pores excessively develop and lose connections between particles, a large pore diameter is therefore desired for the fuel cell electrodes.     

Granulation of a hardmetal powder for spark plasma sintering

A fluidized bed granulation method, pressure swing granulation (PSG), was applied to granulation of a hardmetal powder without pressing lubricants for making the upstream process of spark plasma sintering (SPS) more efficient.

The properties of the granules were examined and compared with those of spray dried granules and extruded ones under the present system using a sieve.

Spherical granules between 0.15 and 0.84 mm in diameter difficult to obtain by the spray drying were obtained with high yield. The flowability of the granules was far better than that of spray dried granules and similar to that of extruded ones. Iron contamination and oxidization during pressure swing granulation were tolerable to the real production.     

Indentation-induced ductile behavior of glass–ceramics involving layered aluminosilicates

Contact damage in materials is critical in engineering applications because it influences mechanical resistance, such as wear, erosion, and impact failure. Indentation tests were performed using a tungsten carbide ball indenter (Hertzian contact) on the surfaces of glass–ceramics containing hexagonal CaAl₂Si₂O₈ or mica crystals (fluorophlogopite), both of which have a layered structure. The stress–strain relation and the permanent deformation on the surface, as well as the observation of the microcrack zone by X-ray computed tomography using synchrotron radiation, revealed that the glass–ceramic with hexagonal CaAl₂Si₂O₈ showed ductility similar to the quasi-plastic behavior previously observed in the mica glass–ceramic. The yield stresses of the glass–ceramics were estimated from the stress deviating from the stress–strain relation assuming complete elastic response between the ball and the sample. The ratio of the yield stress to Young modulus (Y/E) of the glass–ceramic with hexagonal CaAl₂Si₂O₈ was determined to be higher than that of the mica glass–ceramic.     

不同的表面处理对针织碳纤维复合材料的影响分析(英文)

纤维复合材料已经研究了数十年了。他们有着比传统材料,如钢材,优秀的多的力学性能。然而,由于相对较低的产量,梭织、编织与其3D纤维结构的复合材料被认为较难大量生产。因此,近年来,针织物在复合材料界获得了较高的关注,它的高度可塑性使针织复合材料可以直接生产制造成各种复杂形状的复合材料如管状、圆锥型等,使得材料的浪费可以降到了最低。本文使用了有表面处理和没有表面处理的纬编平针碳纤维制成复合材料。对两种复合材料的经向和纬向分别做了拉伸试验。结果显示:有表面处理的材料具有更好的拉伸性能,尤其是在wale方向上,有表面处理的复合材料比没有表面处理的复合材料的拉伸强度提高75.68%。     

Characterization and CO2 sorption properties of poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane‐ co‐3‐methacryloxypropyltris(trimethylsiloxy)silane]

Poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane (MAPOSS)‐co‐3‐methacryloxypropyltris(trimethylsiloxy)silane (SiMA)] was synthesized through free radical polymerization. The physical and carbon dioxide (CO₂) sorption properties of the copolymer membranes were investigated in terms of the MAPOSS content. As the MAPOSS content increases, the membrane density increased, suggesting a decrease in the fractional free volume. In addition, the thermal stability was improved with increasing the MAPOSS content. These are because of the polyhedraloligomericilsesquioxane (POSS) units that restrict the high mobility of poly(SiMA) segments. The glass transition temperature, T_g of the copolymers was single T_g based on the differential scanning calorimetry, suggesting that the copolymers were random and not phase separation. Based on the CO₂ sorption measurement, the POSS units play a role in reducing Henry's dissolution by suppressing the mobility of the poly(SiMA) component, while POSS units increase the nonequilibrium excess free volume, which contributes to the Langmuir dissolution. Based on these results, the introduction of MAPOSS unit is one of the effective ways to improved the thermal stability and CO₂ sorption property due to the enhancement of the polymer rigidity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthetic Molecular Gear Based on Double-Decker Porphyrin Complexes

New rotary molecular machines (1 and 2) were synthetically constructed from two distinct porphyrin-based rotors, a cerium(IV) bis(porphyrinate)s double-decker (CeDD) and a porphyrinatorhodium(III)-based rotor. These rotors are adjacently mounted on rotational axes aligned to near vertical as resembling the bevel-gear-shaped structure. Structural study using NMR analysis reveals that these distinct rotors are connected through a coordination bond between rhodium(III) and a pyridyl group. At temperature from 193 to 393 K, each rotor represents rotational motion driven by heat fluctuation without decomposition into the corresponding precursors in dichloromethane-d ₂ and tetrachloroethane-d ₄. Importantly, the mechanical interaction between the teeth of these rotors is strongly dependent on the central metal atom in a DD rotor and the teeth structure in a porphyrinatorhodium(III)-based rotor. Understanding such relationship between the chemical structures and mechanical interaction is of importance for generating cooperative motion in the hybrid machinery system.     

Validation of Platelet Counting Accuracy With the Celltac F Automated Hematology Analyzer

Rapid and accurate analysis of platelet count plays an important role in evaluating hemorrhagic status. Therefore, we evaluated platelet counting performance of a hematology analyzer, Celltac F (MEK-8222, Nihon Kohden Corporation, Tokyo, Japan), that features easy use with low reagent consumption and high throughput while occupying minimal space in the clinical laboratory. All blood samples were anticoagulated with dipotassium ethylenediaminetetraacetic acid (EDTA-2K). The samples were stored at room temperature (18^{^}C–22^{^}C) and tested within 4 hours of phlebotomy. We evaluated the counting ability of the Celltac F hematology analyzer by comparing it with the platelet counts obtained by the flow cytometry method that ISLH and ICSH recommended, and also the manual visual method by Unopette (Becton Dickinson Vacutainer Systems). The ICSH/ISLH reference method is based on the fact that platelets can be stained with monoclonal antibodies to CD41 and/or CD61. The dilution ratio was optimized after the precision, coincidence events, and debris counts were confirmed by the reference method. Good correlation of platelet count between the Celltac F and the ICSH/ISLH reference method (r = 0.99, and the manual visual method (r= 0.93) were obtained. The regressions were y = 0.90 x+9.0 and y=1.11x+8.4, respectively. We conclude that the Celltac F hematology analyzer for platelet counting was well suited to the ICSH/ISLH reference method for rapidness and reliability.